LEMON Manuals: Even more car manuals for everyone

Rear Window Defogger System does not Operate: Procedure

  1. CHECK FOR DTC 
    1. Check for DTC.

      OK

      DTC is not output.

    NG → See step   15 

    OK: Go to next step 

  2. PERFORM ACTIVE TEST USING TECHSTREAM (DEFOGGER RELAY) 
    1. Select the Active Test using the Techstream to generate a control command, and then check that the rear window defogger operates.
      AIR CONDITIONER

      Tester Display Test Part Control Range Diagnostic Note
      Defogger Relay (Rear) Rear window defogger relay operation OFF or ON -
      RESULT

      Result Proceed to
      Rear window defogger operates normally (w/ Navigation System) A
      Rear window defogger operates normally (w/o Navigation System) B
      Rear window defogger does not operate C

    C → See step   7 

    B → See step   5 

    A: Go to next step 

  3. REPLACE DISPLAY AND NAVIGATION MODULE DISPLAY 
    1. Temporarily replace the display and navigation module display with a new or normally functioning one. Refer to REMOVAL .

    NEXT: Go to next step 

  4. CHECK WINDOW DEFOGGER SYSTEM 
    1. Turn the engine switch on (IG).
    2. Check that pressing the defogger switch illuminates the indicator and warms the rear window surface.
    3. Check that after approximately 15 minutes, the indicator light turns off and the rear window defogger deactivates.

      OK

      Rear window defogger system functioning normally.

    NG → See step   13 

    OK → END 

  5. REPLACE MULTI-DISPLAY 
    1. Temporarily replace the multi-display with a new or normally functioning one. Refer to REMOVAL .

    NEXT: Go to next step 

  6. CHECK WINDOW DEFOGGER SYSTEM 
    1. Turn the engine switch on (IG).
    2. Check that pressing the defogger switch illuminates the indicator and warms the rear window surface.
    3. Check that after approximately 15 minutes, the indicator light turns off and the rear window defogger deactivates.

      OK

      Rear window defogger system functioning normally.

    NG → See step   13 

    OK → END 

  7. CHECK FUSE (DEFOG) 
    1. Remove the DEFOG H-fuse from the engine room relay block.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      DEFOG H-fuse Always Below 1 Ω

    NG → REPLACE FUSE 

    OK: Go to next step 

  8. INSPECT DEFOGGER RELAY (DEFOG) 
    Fig 1: Defogger Relay Circuit
    GTY105913Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the defogger relay from the engine room relay block.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      3 - 4 Battery voltage is not applied to terminals 1 and 2 Below 1 Ω
      3 - 5 10 kΩ or higher
      3 - 4 Battery voltage is applied to terminals 1 and 2 10 kΩ or higher
      3 - 5 Below 1 Ω

    NG → REPLACE DEFOGGER RELAY 

    OK: Go to next step 

  9. CHECK HARNESS AND CONNECTOR (DEFOGGER RELAY - BATTERY AND AIR CONDITIONING AMPLIFIER) 
    Fig 2: Identifying E36 Connector Terminal
    GTY131956Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the defogger relay from the engine room relay block.
    2. Disconnect the E36 air conditioning amplifier connector.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      Defogger relay terminal 1 - Body ground Engine switch on (IG) 11 to 14 V
      Defogger relay terminal 5 - Body ground Always 11 to 14 V
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      Defogger relay terminal 2 - E36-24 (RDEF) Always Below 1 Ω
      Defogger relay terminal 2 - Body ground Always 10 kΩ higher

    NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to next step 

  10. CHECK HARNESS AND CONNECTOR (WINDOW DEFOGGER WIRE - DEFOGGER RELAY AND BODY GROUND) 
    Fig 3: Identifying Engine Room Relay Block Connector Terminal
    GTY126883Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Disconnect the S17 and S18 defogger connectors.
    2. Remove the defogger relay from the engine room relay block.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      S17-1 (B) - Defogger relay terminal 3 Always Below 1 Ω
      S18-1 (E) - Body ground
      Defogger relay terminal 4 - Body ground
      S17-1 (B) - Body ground Always 10 kΩ or higher

    NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to next step 

  11. CHECK REAR WINDOW DEFOGGER WIRE 
    Fig 4: Identifying S17 And S18 Connector Terminal
    GTY115618Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Disconnect the S17 and S18 defogger connector.
    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      S17-1 (B) - S18-1 (E) Engine switch on (IG) and defogger switch on 11 to 14 V

    NG → See step   12 

    OK → See step   14 

  12. REPLACE AIR CONDITIONING AMPLIFIER. Refer to  REMOVAL 
  13. REPLACE AIR CONDITIONING AMPLIFIER. Refer to  REMOVAL 
  14. REPAIR OR REPLACE BACK WINDOW GLASS. Refer to  REMOVAL 
  15. GO TO CAN COMMUNICATION SYSTEM. Refer to  DIAGNOSTIC TROUBLE CODE CHART