LEMON Manuals: Even more car manuals for everyone

Inspection Procedure

  1. CHECK TELEVISION DISPLAY (POWER) 
    1. Check if the television display's power is ON.

      OK: Power is ON. 

    NG: TURN TELEVISION DISPLAY ASSEMBLY POWER ON 

    OK: GO TO NEXT STEP 

  2. CHECK TELEVISION DISPLAY (OPENING ANGLE) 
    1. Check if the television display is open 90° or more.

      OK: Open 90° or more. 

      Fig 1: Identifying Television Display Assembly
      G04953886Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT:

      The television display's tilt can be adjusted to 4 positions: 90°, 100°, 110° and 120°.

    NG: OPEN 90° OR MORE 

    OK: GO TO NEXT STEP 

  3. CHECK MODE IN WHICH BLACK SCREEN OCCURRED 
    1. Check the mode in which the black screen occurred.

      Result 

      RESULT CHART

      Result Proceed to
      During navigation image, screen turned black A
      During DVD image, screen turned black B
      During VTR image, screen turned black C

    B: Go to step   6 

    C: Go to step   9 

    A: GO TO NEXT STEP 

  4. CHECK DISPLAY SIGNAL CIRCUIT BETWEEN MULTI-DISPLAY AND TELEVISION DISPLAY ASSEMBLY 
    1. Refer to the display signal circuit between multi-display and television display assembly (see DISPLAY SIGNAL CIRCUIT BETWEEN MULTI-DISPLAY AND TELEVISION DISPLAY ASSEMBLY  ). If the display signal circuit is operating normally, proceed to the next step.
  5. CHECK AVC-LAN CIRCUIT 
    1. Refer to the AVC-LAN circuit (see AVC-LAN CIRCUIT  ). If the AVC-LAN circuit is operating normally, proceed to the next step.

    NEXT: REPLACE TELEVISION DISPLAY (See  TELEVISION DISPLAY (FOR LONG BODY)   ) 

  6. CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - BODY GROUND) 
    1. Disconnect the R19 display connector.
      Fig 2: Identifying Television Display Assembly Connector Terminal
      G04953887Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the waveform according to the value(s) in the table below.

      Standard waveform 

      TESTER CONNECTION SPECIFIED CONDITION

      Tester Connection Condition Specified Condition
      R19-9 (NTSC) - Body ground During DVD image Image signal waveform is output

    NG: Go to step 7 

    OK: REPLACE TELEVISION DISPLAY (See  TELEVISION DISPLAY (FOR LONG BODY)   ) 

  7. DISPLAY SIGNAL CIRCUIT BETWEEN RADIO RECEIVER AND TELEVISION DISPLAY ASSEMBLY 
    1. Refer to the display signal circuit between radio receiver and television display assembly (see DISPLAY SIGNAL CIRCUIT BETWEEN RADIO RECEIVER AND TELEVISION DISPLAY ASSEMBLY  ). If the display signal circuit is operating normally, proceed to the next step.
  8. CHECK AVC-LAN CIRCUIT 
    1. Refer to the AVC-LAN circuit (see AVC-LAN CIRCUIT  ). If the AVC-LAN circuit is operating normally, proceed to the next step.

    NEXT: REPLACE TELEVISION DISPLAY (See  TELEVISION DISPLAY (FOR LONG BODY)   ) 

  9. CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - BODY GROUND) 
    1. Disconnect the R19 display connector.
      Fig 3: Identifying Television Display Assembly Connector Terminal
      G04953887Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the waveform according to the value(s) in the table below.

      Standard waveform 

      TESTER CONNECTION SPECIFIED CONDITION

      Tester Connection Condition Specified Condition
      R19-9 (NTSC) - Body ground During VTR image Image signal waveform is output

    NG: Go to step 10 

    OK: REPLACE TELEVISION DISPLAY (See  TELEVISION DISPLAY (FOR LONG BODY)   ) 

  10. CHECK DISPLAY SIGNAL CIRCUIT BETWEEN VIDEO TERMINAL AND TELEVISION DISPLAY 
    1. Refer to the DISPLAY SIGNAL CIRCUIT BETWEEN VIDEO TERMINAL AND TELEVISION DISPLAY  . If the display signal circuit is operating normally, proceed to the next step.
  11. CHECK AVC-LAN CIRCUIT 
    1. Refer to the AVC-LAN CIRCUIT  . If the AVC-LAN circuit is operating normally, proceed to the next step.

    NEXT: REPLACE TELEVISION DISPLAY (See  TELEVISION DISPLAY (FOR LONG BODY)   )