LEMON Manuals: Even more car manuals for everyone

Front Door: Overhaul

HINT:

  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
    CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
  2. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSY 
    1. Using a screwdriver, detach the clip and claw and remove the front armrest assembly.

      HINT:

      Tape the screwdriver tip before use.

    2. Remove the 3 screws and power window regulator master switch.
      NOTE: Be careful when removing the 3 screws as the switch may fall and become damaged.
      Fig 1: Removing Front Armrest Assembly With Clip & Claw
      G02957899Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. REMOVE DOOR INSIDE HANDLE BEZEL NO.2 LH 
    1. Using a screwdriver, detach the 3 claws and remove the door inside handle bezel.

      HINT:

      Tape the screwdriver tip before use.

      Fig 2: Removing Door Inside Handle Bezel & Detaching Claws Using Screwdriver
      G02957900Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. REMOVE FRONT DOOR WINDOW UPPER BRACKET GARNISH LH 
    1. Using the screwdriver, detach the 2 claws and clip and remove the upper bracket garnish.

      HINT:

      Tape the screwdriver tip before use.

      Fig 3: Detaching Claws & Clip Using Screwdriver & Removing Upper Bracket Garnish
      G02957901Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. REMOVE FRONT DOOR TRIM BOARD SUB-ASSY LH 
    1. Remove the 8 screws.
    2. Using a clip remover, remove the 2 clips.
    3. Using a screwdriver, detach the 3 clips and remove the door panel.

      HINT:

      Tape the screwdriver tip before use.

    4. Disconnect the 2 cables from the inside handle.
    5. Remove the door trim board.
      Fig 4: Removing Front Door Trim Board Sub-Assy With Screws
      G02957902Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. REMOVE DOOR SIDE AIRBAG SENSOR (See  REPLACEMENT  ) 
  7. REMOVE OUTER REAR VIEW MIRROR ASSY LH (See  OUTER REAR VIEW MIRROR ASSY  ) 
  8. REMOVE MULTIPLEX NETWORK DOOR ECU FRONT LH 
    1. Remove the 2 screws and door ECU.
  9. REMOVE FRONT DOOR WEATHERSTRIP NO. 2 
    1. Remove the 2 clips and weatherstrip.
  10. REMOVE FRONT DOOR SERVICE HOLE COVER LH 
    1. Remove the service hole cover.
      NOTE: Remove the remaining tape on the door.
      Fig 5: Removing Front Door Service Hole Cover
      G02957903Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. REMOVE FRONT DOOR SERVICE HOLE COVER NO. 2 
    1. Remove the 4 screws and service hole cover.
  12. REMOVE FRONT DOOR WEATHERSTRIP LH 
    1. Using the clip remover, remove the 4 clips.
    2. Using a screwdriver, detach the 21 clips and remove the door weatherstrip.

      HINT:

      Tape the screwdriver tip before use.

      Fig 6: Removing Door Weatherstrip & Detaching Clips Using Screwdriver
      G02957904Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. REMOVE FRONT DOOR BELT MOLDING LH (See  REPLACEMENT  ) 
  14. REMOVE FRONT DOOR GLASS SUB-ASSY LH 

    HINT:

    Insert a cushion inside the door panel to prevent scratching the glass.

    1. Driver's side:

      Temporarily install the window regulator master switch.

    2. Passenger's side:

      Temporarily install the window regulator switch.

    3. Move the door glass until the 3 nuts appear in the service holes.
      Fig 7: Removing Nuts & Door Glass
      G02957905Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Remove the 3 nuts and door glass.
      NOTE: Be careful when removing the 3 nuts as the door glass may fall and become damaged.

      HINT:

      Remove the glass upward.

    5. Driver's side:

      Remove the window regulator master switch.

    6. Passenger's side:

      Remove the window regulator switch.

  15. REMOVE FRONT DOOR FRAME SUB-ASSY FRONT LOWER LH 
    1. Remove the 2 bolts and lower door frame.

      HINT:

      Remove the frame upward.

      Fig 8: Removing Bolts & Lower Door Frame
      G02957906Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  16. REMOVE FRONT DOOR WINDOW REGULATOR ASSY LH 
    1. Disconnect the connector.
    2. Remove the 7 nuts and window regulator.

      HINT:

      Remove the window regulator through the service hole.

      NOTE: Be careful when removing the bolts as the window regulator may fall and become damaged.
      Fig 9: Removing Window Regulator With Nuts
      G02957907Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  17. REMOVE POWER WINDOW REGULATOR MOTOR ASSY LH FRONT 
    1. Remove the 2 screws and cover.
      Fig 10: Removing Screws & Cover
      G02957908Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using needle nose pliers, remove the drum and wire guide from the motor.
      NOTE: Do not use a screwdriver to remove them. Using a screwdriver may damage the regulator wire.
      Fig 11: Removing Drum & Wire Guide From Motor Using Needle Nose Pliers
      G02957909Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  18. REMOVE DOOR OUTSIDE HANDLE COVER ASSY 
    1. Remove the hole plug.
    2. Using a T30 torx® wrench, loosen the screw and remove the cover with the door lock key cylinder installed.
      Fig 12: Loosening Screw With T30 Wrench & Remove Cover With Door Lock Key Cylinder
      G02957910Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  19. REMOVE FRONT DOOR W/ MOTOR LOCK ASSY LH 
    1. Disconnect the connector.
    2. Disconnect the links from the outside handle frame.
    3. Using a T30 torx® wrench, remove the 4 screws and lock.
  20. REMOVE FRONT DOOR HANDLE ASSY OUTSIDE LH 
    1. Remove the handle by sliding and pulling it in the direction indicated by the arrow mark in Fig 13.
    2. Remove the outside handle pad front and rear.
      NOTE: If the bellcrank lever is not pulled and held when removing the handle, the bellcrank lever will interfere with the handle and become damaged.
      Fig 13: Removing Outside Handle Pad Front & Rear
      G02957911Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  21. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSY LH 
    1. Remove the nut and outside handle frame.
    2. Slide the outside handle frame to remove it.

      HINT:

      Remove the frame through the service hole.

    3. Remove the lock open rod from the outside handle frame.
      Fig 14: Removing Lock Open Rod From Outside Handle Frame
      G02957912Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  22. REMOVE STEREO COMPONENT SPEAKER ASSY (See  STEREO COMPONENT SPEAKER ASSY  ) 
  23. REMOVE DOOR GLASS FEMALE STABILIZER LH 
    1. Remove the 2 screws and glass female stabilizer.
  24. INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSY LH 
    1. Install the lock open rod to the outside handle frame.
    2. Install the frame with the nut.

      Torque: 7.0 N.m (71 kgf.cm, 62 in.lbf) 

      NOTE: A cover should be inserted between the nut and the door panel.
      Fig 15: Installing Lock Open Rod To Outside Handle Frame
      G02957913Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  25. INSTALL FRONT DOOR HANDLE ASSY OUTSIDE LH 
    1. Install the outside handle pad front and rear.
    2. Pull and hold the bellcrank lever of the frame as shown in Fig 16.
      Fig 16: Pulling & Holding Bellcrank Lever Of Frame
      G02957914Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Install the handle by pushing it in the direction of the arrow marks in Fig 17.
      NOTE: If the bellcrank lever is not pulled and held when installing the handle, the bellcrank lever will interfere with the handle and become damaged.
      Fig 17: Installing Handle
      G02957915Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  26. INSTALL FRONT DOOR W/MOTOR LOCK ASSY LH 
    1. Using a T30 torx® wrench, install the door lock with the 4 screws.

      Torque: 5.5 N.m (56 kgf.cm, 48 in.lbf) 

    2. Connect the link to the outside handle.
    3. Connect the connector.
  27. INSTALL DOOR OUTSIDE HANDLE COVER ASSY 
    1. Using a T30 torx® wrench, install the cover (with the door lock key cylinder installed) with the screw.

      Torque: 7.0 N.m (77 kgf.cm, 62 in.lbf) 

    2. Install the hole plug.
      Fig 18: Using T30 Wrench To Install Cover With Door Lock Key Cylinder Installed With Screw
      G02957916Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  28. INSTALL POWER WINDOW REGULATOR MOTOR ASSY LH FRONT 
    1. Apply MP grease to the sliding and rotating areas of the power window regulator.
      Fig 19: Applying MP Grease To Sliding & Rotating Areas Of Power Window Regulator
      G02957917Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Apply MP grease to the sliding and rotating areas of the motor.
      Fig 20: Applying MP Grease To Sliding & Rotating Areas Of Motor
      G02957918Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. With the holding tool installed, match the holding tool with the motor housing.
    4. Push down on the wire guide and drum, and insert the drum into the motor housing.
      NOTE: If you cannot insert the drum into the motor, slowly slide the bracket (see step  a) for installing the glass, and insert the drum while aligning the drive shaft of the motor with the drum.
      Fig 21: Inserting Drum Into Motor Housing
      G02957919Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Install the cover plate with the 2 screws.
      Fig 22: Installing Cover Plate With Screws
      G02957920Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  29. INSTALL FRONT DOOR WINDOW REGULATOR ASSY LH 
    1. Apply MP grease to the sliding and rotating parts of the window regulator.
      NOTE: Do not apply grease to the spring of the front door window regulator.
      Fig 23: Applying MP Grease To Sliding & Rotating Parts Of Window Regulator
      G02957921Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the front door window regulator with the 7 nuts.

      Torque: 

      5.5 N.m (56 kgf.cm, 48 in.lbf) for motor side 8.0 N.m (82 kgf.cm, 71 in.lbf) for upper side 13.0 N.m (133 kgf.cm, 10 ft.lbf) for lower side 

      Fig 24: Installing Front Door Window Regulator With Nuts
      G02957922Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Initialize the power window control system.
      1. Driver's side:

        Temporarily install the window regulator master switch.

      2. Passenger's side:

        Temporarily install the window regulator switch.

      3. Turn the ignition switch ON.
      4. Fully close the door glass by manual operation.
      5. Using a ø 2 mm (0.079 in.) round bar, keep the reset switch pressed.
      6. Fully open the door glass by manual operation with the reset switch pressed.
      7. Remove the round bar from the reset switch and then fully close the door glass by manual operation.
      8. Check if AUTO UP -> AUTO DOWN operates.
        CAUTION: Be careful as the jam protection function does not operate just after the initialization is performed.
        Fig 25: Removing Round Bar From Reset Switch
        G02957923Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      9. After closing the window fully by AUTO UP operation, initialize the regulator again when performing the reverse operation.
      10. Check that the power window functions.
      11. Driver's side:

        Remove the window regulator master switch.

      12. Passenger's side:

        Remove the window regulator switch.

  30. INSPECT FRONT DOOR GLASS SUB-ASSY LH 
    1. Check that the clearance measurements of areas A to E are within the standard range.
      Fig 26: Identifying Front Door Glass Sub-Assy LH Clearance
      G02957924Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard: 

      AREA SPECIFICATIONS

      Area Measurement Area Measurement
      A 5.3 mm (0.209 in.) D 9.8 mm (0.386 in.)
      B 9.7 mm (0.382 in.) E 6.0 to 10 mm (0.236 to 0.394 in.)
      C 6.5 mm (0.256 in.) - -
      NOTE: Be careful that the circle-marked weatherstrip marked areas by circles are not cut during door glass adjustment.
  31. ADJUST FRONT DOOR GLASS SUB-ASSY LH 
    1. Adjust the upper end of the front door glass horizontally.
      1. Loosen the 2 nuts at the bottom of the window regulator and the nut of the front door mirror bracket.
      2. Adjust the fitting of the front door glass at the upper end in the horizontal direction by turning the stud bolt with a 4 mm hexagon wrench.

        HINT:

        When the stud bolt is loosened, the upper end of the glass leans to the inside of the vehicle. When the stud bolt is tightened, the upper end leans to the outside.

        Fig 27: Loosening Nuts At Bottom Of Window Regulator
        G02957925Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      3. Tighten the 2 nuts after adjustment.

        Torque: 8.0 N.m (82 kgf.cm, 71 in.lbf) 

    2. Adjust the at the bottom of the front door glass horizontally.
      1. Loosen the 2 nuts.
      2. Adjust the fitting at the bottom of the front door glass in the horizontal direction.
      3. Tighten the 2 nuts after adjustment.

        Torque: 8.0 N.m (82 kgf.cm, 71 in.lbf) 

        Fig 28: Loosening Nuts
        G02957926Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Adjust the slant of the front door glass (when fully closed) in the up/down direction and in the front/rear direction.
      1. Loosen the installation bolts for the front door glass stopper, and install the glass temporarily at the upper end.
      2. Loosen the 3 installation nuts for the front door glass.
      3. By operating the power window regulator master switch assembly, stop the front door glass at approximately 3 mm (0.118 in.) before the fully closed position.
        Fig 29: Identifying Front Door Glass Stopper
        G02957927Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      4. Adjust the slant of the front door glass in the up/down direction and in the front/rear direction while holding up the glass.
      5. While holding the front door glass in the fully closed position, press it lightly toward the front door glass stopper and then tighten the bolts and nuts properly.

        Torque: 11.5 N.m (117 kgf.cm, 8.5 ft.lbf) 

    4. Initialize the power window control system.
      1. Driver's side:

        Temporarily install the window regulator master switch.

        Fig 30: Installing Window Regulator Master Switch
        G02957928Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Passenger's side:

        Temporarily install the window regulator switch.

      3. Turn the ignition switch ON.
      4. Fully close the door glass by manual operation.
      5. Using a round bar ø 2 mm (0.079 in.) round bar, keep the reset switch pressed.
      6. Fully open the door glass by manual operation with the reset switch pressed.
      7. Remove the round bar from the reset switch and then fully close the door glass by manual operation.
      8. Check if AUTO UP -> AUTO DOWN operates.
        Fig 31: Removing Round Bar From Reset Switch
        G02957929Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        CAUTION: Be careful the jam protection function does not operate just after the initialization is performed.
      9. After closing the window fully by AUTO UP operation, initialize the regulator again when performing the reverse operation.
      10. Check that the power window functions.
      11. Driver's side:

        Remove the window regulator master switch.

      12. Passenger's side:

        Remove the window regulator switch.

  32. INSTALL FRONT DOOR SERVICE HOLE COVER LH 
    1. Install the service hole cover to the door panel.

      HINT:

      • When installing the service hole cover, pull out the links and connectors through the service hole cover.
      • There should be no wrinkles or folds after attaching the service hole cover.
      • After attaching the service hole cover, sealing condition should be confirmed.
        Fig 32: Installing Service Hole Cover To Door Panel
        G02957930Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  33. INSTALL DOOR SIDE AIRBAG SENSOR (See  REPLACEMENT  ) 
  34. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 
  35. PERFORM INITIALIZATION (See  INITIALIZATION  ) 
    NOTE: Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.