LEMON Manuals: Even more car manuals for everyone

Generator ASSY (3MZ-FE): Overhaul

  1. REMOVE GENERATOR PULLEY 

    SST 09820-63010 (09820-06010, 09820-06020)

    HINT:

    SST

    SST 1 -A and B 09820-06010
    SST 2 09820 - 06020
    1. Hold SST 1 -A with a torque wrench, and tighten SST 1 -B clockwise with the specified torque.
      Fig 1: Tightening SST
      G03012544Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Torque: 39 N.m (400 kgf.cm, 29 ft.lbf) 

      NOTE: Check that SST is secured to the rotor shaft.
    2. Clamp SST 2 in a vise.
    3. Insert SST 1-A and B into SST 2, and attach the pulley nut to SST 2.
      Fig 2: Inserting SST 1-A And B Into SST 2
      G03012545Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. To loosen the pulley nut, turn SST 1-A in the direction shown in Fig 3 .
      Fig 3: Loosening Pulley Nut
      G03012546Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE: To prevent damage to the rotor shaft, do not loosen the pulley nut more than one-half turn.
    5. Remove the generator from SST 2.
    6. Turn SST 1-B, and remove SST 1-A and B.
    7. Fig 4: Removing Generator Pulley
      G03012547Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    8. Remove the pulley nut, and then remove the generator pulley.
  2. REMOVE GENERATOR REAR END COVER 
    1. Place the generator on the generator pulley.
    2. Remove the 3 nuts, and then remove the generator rear end cover.
      Fig 5: Removing Generator Rear End Cover
      G03012548Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. REMOVE TERMINAL INSULATOR 
    1. Remove the terminal insulator from the generator coil.
      Fig 6: Removing Terminal Insulator
      G03012549Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. REMOVE GENERATOR BRUSH HOLDER ASSY 
    1. 100A Generator
      1. Remove the 2 screws, and then remove the generator brush holder.
        Fig 7: Removing Generator Brush Holder Assy (100A Generator)
        G03012550Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. 130A Generator
      1. Remove the generator plate seal.
      2. Remove the 2 screws, and then remove the generator brush holder.
      3. Remove the generator plate seal.
        Fig 8: Removing Generator Brush Holder Assy (130A Generator)
        G03012551Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. REMOVE GENERATOR COIL ASSY 
    1. Remove the 4 bolts.
      Fig 9: Removing Generator Coil Assy Bolts
      G03012552Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using SST, remove the generator coil.

      SST 09950-4001 1 (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)

      Fig 10: Removing Generator Coil
      G03012553Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. REMOVE GENERATOR ROTOR ASSY 
    1. Remove the generator washer and the generator rotor.
      Fig 11: Removing Generator Washer And Rotor
      G03012554Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. INSPECT GENERATOR BRUSH HOLDER ASSY 
    1. Check the brush length. (100A Generator)
      Fig 12: Checking Generator Brush Length (100A Generator)
      G03012555Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Using vernier calipers, measure the exposed brush length.

        Standard exposed brush length: 

        10.5 mm (0.413 in.) 

        Minimum exposed brush length: 4.5 mm (0.177 in.) 

        If the exposed brush length is less than minimum, replace the generator brush holder.

    2. Check the brush length. (130A Generator)
      1. Using vernier calipers, measure the exposed brush length.
        Fig 13: Checking Generator Brush Length (130A Generator)
        G03012556Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        Standard exposed brush length: 

        10.5 mm (0.413 in.) 

        Minimum exposed brush length: 4.5 mm (0.177 in.) 

        If the exposed brush length is less than minimum, replace the generator brush holder.

  8. INSPECT GENERATOR ROTOR ASSY 
    1. Check that bearing is not rough or worn.
      Fig 14: Checking Generator Rotor Assy
      G03012557Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      If necessary, replace the generator rotor. (100A Generator)

      If necessary, replace the generator rotor bearing. (130A Generator)

    2. Check if the rotor has open circuit.
      1. Using an ohmmeter, measure the resistance between the slip ring.
        Fig 15: Checking For Generator Rotor Open Circuit
        G03012558Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        Resistance: 

        2.3 to 2.7Ω at 20°C (68°F) for 100A Generator 

        1.5 to 1.9Ω at 20°C (68°F) for 130A Generator 

        If the resistance is not as specified, replace the generator rotor.

    3. Check if the rotor has ground.
      Fig 16: Checking Generator Rotor Ground Circuit
      G03012559Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Using an ohmmeter, check that there is no continuity between the slip ring and rotor core.

        If there is continuity, replace the generator rotor.

    4. Inspect slip rings.
      1. Check that the slip rings are not rough or scored.

        If rough or scored, replace the generator rotor.

    5. Check the slip ring diameter.
      1. Using vernier calipers, measure the slip ring diameter.
        Fig 17: Checking Slip Ring Diameter
        G03012560Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        Standard diameter: 

        14.2 to 14.4 mm (0.559 to 0.567 in.) 

        Minimum diameter: 14.0 mm (0.551 in.) 

        If the diameter is less than minimum, replace the generator rotor.

  9. REMOVE GENERATOR ROTOR BEARING (130A GENERATOR) 
    1. Using SST, remove the generator bearing cover (outside) and bearing.

      SST 09820-00021

      Fig 18: Removing Generator Rotor Bearing (130A Generator)
      G03012561Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE: Be careful not to damage the fan.
    2. Remove the generator bearing cover (inside).
  10. INSTALL GENERATOR ROTOR BEARING (130A GENERATOR) 
    1. Place the generator rotor on the generator pulley.
    2. Install the generator bearing cover (inside).
    3. Using SST and a press, press in a new bearing.

      SST 09820-00031

      Fig 19: Installing Generator Rotor Bearing (130A Generator)
      G03012562Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Using SST, push in the generator bearing cover (outside).

      SST 09285-76010

      Fig 20: Installing Generator Rotor Bearing (130A Generator) Cover (Outside)
      G03012563Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. INSPECT GENERATOR DRIVE END FRAME BEARING 
    1. Check that bearing is not rough or worn.

      If necessary, replace the bearing.

      Fig 21: Inspecting Generator Drive End Frame Bearing
      G03012564Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. REMOVE GENERATOR DRIVE END FRAME BEARING 
    1. Remove the 4 screws, and remove the retainer plate.
      Fig 22: Removing Generator Drive End Frame Bearing Retainer Plate
      G03012565Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using SST, tap out the bearing.

      SST 09950-60010 (09951-00250), 09950-70010 (09951-07100)

      Fig 23: Removing Generator Drive End Frame Bearing
      G03012566Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. INSTALL GENERATOR DRIVE END FRAME BEARING 
    1. Using SST and a press, press in a new bearing.
      Fig 24: Installing Generator Drive End Frame Bearing
      G03012567Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the retainer plate with the 4 screws.

      Torque: 2.3 N.m (23 kgf.cm, 20 in.lbf) 

      SST 09950-60010 (09951-00470), 09950-70010 (09951-07100)

      Fig 25: Installing Generator Drive End Frame Bearing Retainer Plate
      G03012568Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  14. INSTALL GENERATOR ROTOR ASSY 
    1. Place the generator drive end frame on the generator pulley.
    2. Install the generator rotor and the generator washer.
      Fig 26: Installing Generator Rotor Assy
      G03012569Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. INSTALL GENERATOR COIL ASSY 
    Fig 27: Installing Generator Coil Assy
    G03012570Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. 100A Generator
      1. Using deep socket wrench 21 and a press, press in the coil carefully.
    2. 130A Generator
      1. Using deep socket wrench 20 and a press, press in the coil carefully.
    3. Tighten the 4 bolts.

      Torque: 5.8 N.m (59 kgf.cm, 51 in.lbf) 

      Fig 28: Tightening Generator Coil Assy Bolts
      G03012571Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  16. INSTALL GENERATOR BRUSH HOLDER ASSY 
    1. 100A Generator
      1. While pushing the 2 brushes to inside the brush holder, insert a pin (diameter 1.0 mm (0.039 in.)) into the brush holder hole.
        Fig 29: Installing Generator Brush (100A Generator)
        G03012572Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Install the generator brush holder with the 2 screws.

        Torque: 1.8 N.m (18 kgf.cm, 16 in.lbf) 

      3. Pull out the pin (diameter 1.0 mm (0.039 in.)) from the generator brush holder.
        Fig 30: Installing Generator Brush Holder Assy (100A Generator)
        G03012573Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. 130A Generator
      1. Install the generator plate seal (inside).
      2. Fig 31: Installing Generator Brush Holder Assy (130A Generator)
        G03012574Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      3. Place the generator brush holder with the pin facing upward.
        NOTE: Be careful of the generator brush holder installing direction.
      4. Tighten the 2 screws.

        Torque: 1.8 N.m (18 kgf.cm, 16 in.lbf) 

      5. Align the pins of the generator brush holder with the holes of the generator plate seal (outside), and install the generator plate seal (outside).
  17. INSTALL TERMINAL INSULATOR 
    1. Install the terminal insulator.
      Fig 32: Installing Terminal Insulator
      G03012575Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE: pay attention the mounting orientation of the terminal insulator.
  18. INSTALL GENERATOR REAR END COVER 
    1. Install the generator rear end cover with the 3 nuts.

      Torque: 4.6 N.m (47 kgf.cm, 41 in.lbf) 

      Fig 33: Installing Generator Rear End Cover
      G03012576Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  19. INSTALL GENERATOR PULLEY 

    SST 09820-63010 (09820-06010, 09820-06020)

    HINT:

    SST

    SST 1 -A and B 09820-06010
    SST 2 09820 - 06020
    1. Install the generator pulley to the rotor shaft by tightening the generator pulley nut by hand.
    2. Hold SST 1-A with a torque wrench, and tighten SST 1 -B clockwise with the specified torque.
      Fig 34: Installing Generator Pulley
      G03012577Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Torque: 39 N.m (400 kgf.cm, 29 ft.lbf) 

      NOTE: Check that SST is secured to the rotor shaft.
    3. Clamp SST 2 in a vise.
    4. Insert SST 1-A and B into SST 2, and attach the generator pulley nut to SST 2
      Fig 35: Inserting SST 1-A And B Into SST 2
      G03012578Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Tighten the generator pulley nut by turning SST 1 -A in the direction shown in Fig 36 .
      Fig 36: Identifying Tightening Direction Of Generator Pulley Nut
      G03012579Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Torque: 111 N.m (1,125 kgf.cm, 81 ft.lbf) 

    6. Remove the generator from SST 2.
    7. Turn SST 1-B, and remove SST 1-A, B.
    8. Turn the generator pulley, and check that the generator pulley moves smoothly.
      Fig 37: Checking Movement Of Generator Pulley
      G03012580Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002