LEMON Manuals: Even more car manuals for everyone

Vane Pump ASSY: Overhaul

  1. DRAIN POWER STEERING FLUID (  ON-VEHICLE INSPECTION  ) 
  2. REMOVE AIR CLEANER ASSY 
  3. REMOVE VANE PUMP V BELT 
    1. Loosen the belt tension by turning the belt tensioner counterclockwise, and remove the belt.
      Fig 1: Removing Vane Pump V Belt
      G00919083Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. SEPARATE OIL RESERVOIR TO PUMP HOSE NO.1 
    1. Loosen the 2 clips and disconnect the 2 vacuum hoses.
      Fig 2: Removing Oil Reservoir To Pump Hose
      G00919084Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Loosen the clip and disconnect the hose.
      Fig 3: Disconnecting Clip And Hose
      G00919085Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. SEPARATE PRESSURE FEED TUBE ASSY 
    1. Remove the union bolt and a gasket, disconnect the pressure feed tube.
      Fig 4: Removing Pressure Feed Tube Assy
      G00919086Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. REMOVE VANE PUMP ASSY 
    1. Remove the 2 bolts and nut.
    2. Using a Torx socket (E10), remove the stud bolt.
      Fig 5: Removing Vane Pump Assy
      G00919087Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. MEASURE VANE PUMP ROTATION TORQUE 
    1. Check that the pump rotates smoothly without abnormal noise.
    2. Using a torque wrench, check the pump rotating torque.
      1. Rotating torque: 0.27 N.m (2.8 kgf.cm, 2.4 in. lbf) or less 
      Fig 6: Measuring Vane Pump Rotation Torque
      G00919088Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. REMOVE VANE PUMP PULLEY 
    1. Using SST to stop the pulley rotating, loosen the nut.
      1. SST 09960-10010 (09962-01000, 09963-01000)
    2. Remove the nut and vane pump pulley from the vane pump shaft.
      Fig 7: Removing Vane Pump Pulley
      G00919089Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. REMOVE POWER STEERING SUCTION PORT UNION 
    1. Remove the bolt and suction port union.
    2. Remove the O-ring from the suction port union.
  10. REMOVE PRESSURE PORT UNION 
    1. Remove the pressure port union, flow control valve and spring.
    2. Remove the O-ring from the pressure port union.
  11. REMOVE VANE PUMP HOUSING REAR 
    1. Remove the 4 bolts and vane pump housing rear.

      HINT:

      If the wave washer and side plate are stuck to the vane pump housing rear, lightly tap the vane pump housing rear with a plastic hammer, and remove the wave washer and side plate.

    2. Remove the 2 O-rings from the rear housing.
  12. REMOVE SIDE PLATE AND WAVE WASHER 
  13. REMOVE VANE PUMP CAM RING 
    1. Using a screwdriver, remove the snap ring from the vane pump shaft.
    2. Remove the cam ring.
  14. REMOVE VANE PUMP ROTOR 
    1. Remove the vane pump rotor with the 10 vane plates.
    NOTE: Be careful not to drop the plate.
  15. REMOVE VANE PUMP SHAFT 
  16. REMOVE STRAIGHT PIN 
    1. Remove the 2 pins from the vane pump housing front.
  17. REMOVE VANE PUMP HOUSING OIL SEAL 
    NOTE: When using a vise, do not overtighten it.
    1. Using a screwdriver with vinyl tape wound around its tip, remove the housing oil seal.
    NOTE: Be careful not to damage the vane pump housing front.
    Fig 8: Removing Vane Pump Housing Oil Seal
    G00919090Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  18. INSPECT OIL CLEARANCE 
    1. Using a micrometer and a caliper gauge, measure the oil clearance.
      1. Standard clearance: 0.027 - 0.054 mm (0.0011 - 0.0021 in.) 
      2. Maximum clearance: 0.07 mm (0.0028 in.) 

    If it is more than the maximum, replace the vane pump assy.

    Fig 9: Identifying Vane Pump Shaft And Bushing
    G00919091Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  19. INSPECT VANE PUMP ROTOR AND VANE PUMP PLATES 
    Fig 10: Measuring Pump Plate
    G00919092Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using a micrometer, measure the height, thickness and length of the 10 vane plates.
      1. Minimum height: 8.6 mm (0.33858 in.) 
      2. Minimum thickness: 1.397 mm (0.05500 in.) 
      3. Minimum length: 14.991 mm (0.59020 in.) 
    2. Using a feeler gauge, measure the clearance between the vane pump rotor grove and vane plate.
      1. Maximum clearance: 0.033 mm (0.00130 in.) 

      If it is more than the maximum, replace the vane pump assy.

    Fig 11: Measuring Vane Pump Rotor Groove
    G00919093Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  20. INSPECT FLOW CONTROL VALVE 
    1. Coat the flow control valve with power steering fluid and check that it falls smoothly into the flow control valve hole by its own weight.
      Fig 12: Inspecting Flow Control Valve
      G00919094Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Check the flow control valve for leakage. Close one of the holes and apply compressed air of 392 - 490 kPa (4 - 5 kgf.cm2 , 57 - 71 psi) into the opposite side hole, and confirm that air does not come out from the end holes.

      If air comes out from the end holes, replace the vane pump assy.

      Fig 13: Checking Flow Control Valve For Leakage
      G00919095Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  21. INSPECT FLOW CONTROL VALVE COMPRESSION SPRING 
    1. Using vernier calipers, measure the free length of the spring.
      1. Minimum free length: 32.1 mm (1.264 in.) 

    If it is not within the specification, replace the spring.

    Fig 14: Measuring Flow Control Valve Compression Spring
    G00919096Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  22. INSPECT PRESSURE PORT UNION 

    If the pressure union seat in the pressure port union is remarkably damaged and it may cause fluid leakage, fluid leakage, replace the pressure port union.

  23. INSTALL VANE PUMP HOUSING OIL SEAL 
    1. Coat a new oil seal lip with power steering fluid.
    2. Using SST, press in the oil seal.
      1. SST 09950-60010 (09951-00320), 09950-70010 (09951-07100)
      NOTE: Make sure to install the oil seal facing in the correct direction.
      Fig 15: Installing Vane Pump Housing Oil Seal
      G00919097Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  24. INSTALL VANE PUMP SHAFT 
  25. INSTALL STRAIGHT PIN 
    1. Using a plastic hammer, tap the 2 new pins to the vane pump housing front.
    NOTE: Be careful no to damage the pins.
  26. INSTALL VANE PUMP CAM RING 
    1. Install the cam ring with the inscribed mark facing outward.

    HINT:

    Align the holes of the cam ring with the straight pins.

  27. INSTALL VANE PUMP ROTOR 
    1. Install the vane pump rotor with the inscribed mark facing outward.
    2. Install a new snap ring to the vane pump shaft.
      Fig 16: Installing Vane Pump Cam Ring
      G00919098Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Install the 10 plates with the round and facing outward.
    4. Install a new gasket on the front housing.
    NOTE: Be careful of the direction of the gasket.
    Fig 17: Installing Plates Of Vane Pump Rotor
    G00919099Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  28. INSTALL VANE PUMP SIDE PLATE REAR 
    1. Align the holes of the plate and 2 straight pins.
  29. INSTALL VANE PUMP HOUSING REAR 
    1. Install the wave washer so that its protrusions fit into the slots in the side plate.
    2. Coat 2 new O-rings with power steering fluid and install them to the rear housing.
    3. Install the rear housing with the 4 bolts.
      1. Torque: 24 N.m (240 kgf.cm, 17 ft.lbf) 
      Fig 18: Installing Wave Washer
      G00919100Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  30. INSTALL PRESSURE PORT UNION 
    1. Install the spring to the vane pump housing front.
    2. Install the flow control valve facing the correct direction (See page 51 -7).
    3. Coat a new O-ring with power steering fluid and install it to the pressure port union.
    4. Instal the pressure port union.
      1. Torque: 83 N.m (850 kgf.cm, 61 ft.lbf) 
  31. INSTALL POWER STEERING SUCTION PORT UNION 
    1. Coat a new O-ring with power steering fluid and install it to the suction port union.
    2. Install the suction port union with the bolt.
      1. Torque: 13 N.m (130 kgf.cm, 9 ft.lbf) 
  32. INSTALL VANE PUMP PULLEY 
    1. Install the vane pump pulley and nut to the vane pump shaft.
    2. Using SST to stop the pulley rotating, torque a new pulley set nut.
      1. SST 09960-10010 (09962-01000, 09963-01000)
      2. Torque: 44 N.m (449 kgf.cm, 32 ft.lbf) 
      Fig 19: Installing Vane Pump Pulley
      G00919101Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  33. MEASURE VANE PUMP ROTATION TORQUE 
    1. Check that the pump rotates smoothly without abnormal noise.
    2. Using a torque wrench, check the pump rotating torque.
      1. Rotating torque: 0.27 N.m (2.8 kgf.cm, 2.4 in. lbf) or less 
      Fig 20: Measuring Vane Pump Rotation Torque
      G00919102Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  34. INSTALL VANE PUMP ASSY 
    1. Using a Torx socket (E10), install the vane pump with the stud bolt.
      1. Torque: 22 N.m (224 kgf.cm, 16 ft.lbf) 
    2. Install the 2 bolts and nut.
      1. Torque: 43 N.m (438 kgf.cm, 32 ft.lbf) 
      Fig 21: Installing Vane Pump Assy
      G00919103Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  35. INSTALL VANE PUMP V BELT 
    1. Loosen the belt tension by turning the belt tensioner counterclockwise, and install the belt.
      Fig 22: Installing Vane Pump V Belt
      G00919104Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  36. CONNECT PRESSURE FEED TUBE ASSY 
    1. Install the union bolt with a new gasket on each side of the tube.
      1. Torque: 51 N.m (520 kgf.cm, 38 ft.lbf) 
      Fig 23: Connecting Pressure Feed Tube Assy
      G00919105Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  37. CONNECT OIL RESERVOIR TO PUMP HOSE NO.1 
    1. Install the hose with the clip.
      Fig 24: Connecting Oil Reservoir To Pump Hose
      G00919106Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the 2 hose with the 2 clip.
      Fig 25: Installing Hose With Clip
      G00919107Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  38. INSTALL AIR CLEANER ASSY 
  39. ADD POWER STEERING FLUID (See page 51 -3) 
  40. BLEED POWER STEERING FLUID (See page 51 -3) 
  41. INSPECT FLUID LEAK (See page 51 -3)