LEMON Manuals: Even more car manuals for everyone

Power Steering Link ASSY: Overhaul

  1. PRECAUTION (See  AIR BAG SAFETY PRECAUTIONS  ) 
  2. DISCONNECT BATTERY NEGATIVE TERMINAL 
  3. PLACE FRONT WHEELS FACING STRAIGHT AHEAD (See  OVERHAUL  ) 
  4. REMOVE HORN BUTTON ASSY 
  5. REMOVE STEERING WHEEL ASSY (See  OVERHAUL  ) 
    1. SST 09950-50013 (09951-05010, 09952-05010, 09953-05020, 09954-05021)
  6. REMOVE STEERING COLUMN COVER LWR (See  OVERHAUL  ) 
  7. REMOVE TURN SIGNAL SWITCH ASSY (See  OVERHAUL  ) 
  8. REMOVE SPIRAL CABLE SUB-ASSY (See  OVERHAUL  ) 
  9. REMOVE FRONT WHEEL 
  10. REMOVE ENGINE UNDER COVER ASSY REAR 
    1. Remove the 6 bolts and engine under cover assy rear.
  11. REMOVE ENGINE UNDER COVER SUB-ASSY NO.1 
    1. Remove the 4 bolts and engine under cover sub-assy No.1.
  12. REMOVE STABILIZER BAR FRONT (See  STABILIZER BAR  ) 
  13. SEPARATE TIE ROD END SUB-ASSY LH 
    1. Remove the cotter pin and nut.
    2. Using SST, separate the tie rod end from the steering knuckle arm.
      1. SST 09628-62011
      Fig 1: Removing Tie Rod End Sub-Assy
      G00919111Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  14. SEPARATE TIE ROD END SUB-ASSY RH 

    HINT:

    Separate the RH side by the same procedures with the LH side.

    1. SST 09628-62011
  15. REMOVE STEERING INTERMEDIATE SHAFT NO.2 (See  OVERHAUL  ) 
  16. DISCONNECT PRESSURE FEED TUBE ASSY 
    1. Using SST, Loosen the flare nut and disconnect the pressure feed tube.
      1. SST 09023-12700
      Fig 2: Removing Pressure Feed Tube Assy
      G00919112Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the 2 bolts and separate the pressure feed tube assy from frame sub-assy.
      Fig 3: Removing Pressure Feed Tube Assy
      G00919113Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  17. DISCONNECT STEERING GEAR OUTLET RETURN TUBE 
    1. Remove the clip and disconnect the return hose.
      Fig 4: Removing Clip And Disconnect Return Hose
      G00919114Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using SST, remove the outlet return tube.
      1. SST 09023-12700
      Fig 5: Removing Outlet Return Tube
      G00919115Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  18. REMOVE POWER STEERING LINK ASSY 
    1. Remove the 2 bolts, 2 nuts and power steering link assy.
    NOTE: The nut has a detent, so never turn the nut, be sure to turn the bolt.

    HINT:

    After loosen the 2 bolts, raise the bolt from the frame, and slide the gear assy and the bolt as a unit to the position where the bolt can be pulled out, and then remove the bolt.

    Fig 6: Removing Power Steering Link Assy
    G00919116Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  19. FIX POWER STEERING LINK ASSY 
    1. Using SST, remove the 2 turn pressure tubes.
      1. SST 09023-38200
      Fig 7: Removing Turn Pressure Tubes
      G00919117Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using the SST, fix the gear assembly, between aluminum plates in a vise, as shown in the illustration.
      1. SST 09612-00012
      Fig 8: Fitting Gear Assembly In A Vise
      G00919118Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  20. REMOVE TIE ROD END SUB-ASSY LH 
    1. Place matchmarks on the tie rod end, lock nut and rack end.
    2. Loosen the lock nut, remove the tie rod end and lock nut.
    Fig 9: Removing Tie Rod End Sub-Assy
    G00919119Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  21. REMOVE TIE ROD END SUB-ASSY RH 

    HINT:

    Remove the RH side by the same procedures with the LH side.

  22. REMOVE STEERING RACK BOOT CLAMP LH 
    1. Using pliers and a screwdriver, loosen the clamp.
    NOTE: Be careful not to damage the boot.

    HINT:

    Mark the RH and LH boots.

    Fig 10: Removing Steering Rack Boot Clamp
    G00919120Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  23. REMOVE STEERING RACK BOOT CLAMP RH 

    HINT:

    Remove the RH side by the same procedures with the LH side.

  24. REMOVE STEERING RACK BOOT CLIP LH 
    1. Using pliers, remove the clip.
    NOTE: Be careful not to damage the boot.
  25. REMOVE STEERING RACK BOOT CLIP RH 

    HINT:

    Remove the RH side by the same procedures with the LH side.

  26. REMOVE STEERING RACK BOOT LH 
  27. REMOVE STEERING RACK BOOT RH 
  28. REMOVE STEERING RACK END SUB-ASSY 
    1. Using a screwdriver and a hammer, stake back the washer.
      NOTE: Avoid any impact to the steering rack.
      Fig 11: Removing Steering Rack End Sub-Assy
      G00919121Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using a spanner to hold the steering rack steady, and using SST, remove the rack end.
      1. SST 09922-10010
    3. Remove the craw washer.
      NOTE: Use SST 09922-10010 in the direction shown in the illustration.
    4. Employ the same manner described above to the other side.

    HINT:

    Mark the RH and LH rack ends.

    Fig 12: Removing Rack End
    G00919122Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  29. REMOVE RACK GUIDE 
    1. Using SST, remove the lock nut.
      1. SST 09922-10010
      NOTE: Use SST 09922-10010 in the direction shown in the illustration.
      Fig 13: Removing Rack Guide
      G00919123Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using a hexagon wrench (24 mm), remove the rack guide spring cap.
    3. Remove the spring and rack guide.
      Fig 14: Using A Hexagon Wrench
      G00919124Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  30. REMOVE POWER STEERING CONTROL VALVE 
    1. Remove the 2 bolts.
    2. Pull out the control valve assembly with the control valve housing.
    3. Remove the O-ring.
    4. Carefully mount the control valve assembly in a soft jaw vise.
      Fig 15: Removing Power Steering Control Valve
      G00919125Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Using SST, remove the bearing guide nut.
      1. SST 09631-20060
      NOTE: Be careful not to damage the oil seal lip.
    6. Remove the O-ring.
    7. Remove the dust cover.
      Fig 16: Removing Dust Cover
      G00919126Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    8. Using SST and a hammer, drive out the oil seal from the bearing guide nut.
      1. SST 09950-60010 (09951-00300), 09950-70010 (09951-07100)
    9. Wind vinyl tape to the control valve shaft.
      Fig 17: Using SST And A Hammer
      G00919127Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    10. Using a plastic hammer, tap out the valve assembly with the bearing guide nut from the control valve housing.
      NOTE: Be careful not to damage the oil seal lip.
    11. Using a screwdriver, remove the 4 teflon rings from the control valve assembly.
      NOTE: Be careful not to damage the grooves for the ring.
      Fig 18: Using A Screwdriver
      G00919128Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    12. Using a screw extractor, remove the union seat from the control valve housing.
      Fig 19: Using A Screw Extractor
      G00919129Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  31. REMOVE POWER STEERING CONTROL VALVE UPPER OIL SEAL 
    1. Using SST, press out the bearing and oil seal from the control valve housing.
      1. SST 09950-70010 (09951-07150), 09950-60010 (09951-00250)
      Fig 20: Removing Power Steering Control Valve Upper Oil Seal
      G00919130Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  32. REMOVE CYLINDER END STOPPER 
    1. Using SST, remove the stopper.
      1. SST 09631-20120
    2. Remove the O-ring from the stopper.
      Fig 21: Removing Cylinder End Stopper
      G00919131Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  33. REMOVE STEERING RACK AND OIL SEAL 
    1. Using SST, press out the steering rack and oil seal.
      1. SST 09950-70010 (09951 -07200)
      NOTE: Take care not to drop the steering rack.
    2. Remove the oil seal from the steering rack.
      Fig 22: Removing Steering Rack And Oil Seal
      G00919132Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  34. INSPECT POWER STEERING RACK 
    1. Insert a wire into the vent hole of the steering rack by 30 mm (1.18 in.), and ensure that the vent hole is not clogged with grease.

      HINT:

      If the hole is clogged, the pressure inside the boot will change after it is assembled and the steering wheel is turned.

    Fig 23: Checking Power Steering Rack
    G00919133Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  35. INSPECT TIE ROD END SUB-ASSY LH 
    1. Flip the ball joint stud back and forth 5 times as shown in the figure, before installing the nut.
    2. Using a torque wrench, turn the nut continuously at a rate of 2 - 4 seconds per 1 turn and take the torque reading on the 5th turn.
      1. Torque (Turning): 0.29 - 1.96 N.m (2.9 - 20.0 kgf.cm, 2.57 - 17.35 in.lbf) 
      Fig 24: Inspecting Tie Rod End Sub-Assy
      G00919134Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  36. INSPECT TIE ROD END SUB-ASSY RH 

    HINT:

    Inspect the RH side by the same procedures with LH side.

  37. REMOVE STEERING RACK PISTON RING 
    1. Using a screwdriver, remove the teflon ring and O-ring from the steering rack.
    NOTE: Be careful not to damage the groove for the ring.
  38. INSTALL STEERING RACK PISTON RING 
    1. Coat a new O-ring with power steering fluid and install it on steering rack.
    2. Expand a new teflon ring with your fingers.
      NOTE: Be careful no to overexpand the teflon ring.
    3. Coat the teflon ring with power steering fluid.
      Fig 25: Installing Steering Rack Piston Ring
      G00919135Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Install the teflon ring to the steering rack, and settle it down with your fingers.
      Fig 26: Installing Teflon Ring To Steering Rack
      G00919136Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  39. INSTALL POWER STEERING RACK 
    1. Coat SST with power steering fluid.
    2. Install SST to the rack.
      1. SST 09631-00350

      HINT:

      Is necessary, scrape the burrs off the rack teeth end and burnish.

    3. Install the rack into the rack housing.
      Fig 27: Installing Power Steering Rack
      G00919137Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Coat SST with power steering fluid.
      1. SST 09631-00350
    5. Install SST to the steering rack opposite end.
    6. Coat a new oil seal lip with power steering fluid, and install the oil seal by pushing it without tilting.
      NOTE:
      • Make sure to install the oil seal facing in the correct direction.
      • Be careful not to damage the oil seal lip.
    7. Remove the SST.
      1. SST 09631-00350
      Fig 28: Installing SST To Steering Rack Opposite End
      G00919138Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  40. INSTALL CYLINDER END STOPPER 
    1. Coat a new O-ring with power steering fluid, and install it to the stopper.
    2. Using a wooden block and a hammer, drive in the stopper until it is tightly installed.
      NOTE: Be careful no to damage the O-ring.
      Fig 29: Installing Cylinder End Stopper
      G00919139Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Using SST, torque the stopper.
      1. SST 09631-20120
      2. Torque: 145 N.m (1,479 kgf.cm, 107 ft.lbf) 
      Fig 30: Using SST
      G00919140Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  41. AIR TIGHTNESS TEST 
    1. Install SST to the unions of the rack housing.
      1. SST 09631-12071 (09633-00010)
    2. Apply 53.33 kPa (400 mmHg, 15.75 in Hg) of vacuum for about 30 seconds.
    3. Check that there is no change in the vacuum.

    If there is change in the vacuum, check the installation of the oil seals.

    Fig 31: Checking Vacuum In Rack Housing
    G00919141Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  42. INSTALL POWER STEERING CONTROL VALVE UPPER OIL SEAL 
    1. Coat a new oil seal lip with power steering fluid.
    2. Using SST, press in the oil seal.
      1. SST 09950-60010 (09951-00180, 09951-00320, 09952-06010), 09950-70010 (09951-07150)
      NOTE: Make sure that the oil seal is installed facing in the correct direction.
      Fig 32: Installing Power Steering Control Valve Upper Oil Seal
      G00919142Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Coat a new bearing with molybdenum disulfide lithium base grease.
    4. Using SST, press in the bearing.
      1. SST 09950-60010 (09951-00180, 09951-00340, 09952-06010), 09950-70010 (09951-07150)
      Fig 33: Coating New Bearing With Molybdenum Disulfide Lithium Base Grease
      G00919143Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  43. INSTALL POWER STEERING CONTROL VALVE 
    1. Using a plastic hammer and a sliding handle, lightly tap in a new union seat.
      NOTE: Before installing the union seat, remove dust sticking to the control valve housing.
      Fig 34: Installing Power Steering Control Valve
      G00919144Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Coat the rings with power steering fluid.
    3. Expand 4 new rings with your fingers.
      Fig 35: Coating Rings With Power Steering Fluid
      G00919145Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Install the rings to the control valve assembly, and settle them down with your fingers.
    5. Carefully slide the tapered end of SST over the rings until the ring fits to the steering rack.
      1. SST 09631-20081
      NOTE: Be careful not to overexpand the ring.
      Fig 36: Installing Rings To Control Valve Assembly
      G00919146Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Coat the teflon rings with power steering fluid.
    7. To prevent oil seal lip damage, wind vinyl tape on the serrated port of the control valve shaft.
    8. Push the valve assembly into the control valve housing.
      NOTE: Be careful not to damage the teflon rings and oil seal lip.
    9. Coat a new O-ring with power steering fluid, and install it to the bearing guide nut.
    10. Coat a new oil seal lip with power steering fluid.
      Fig 37: Identifying Vinyl Tape
      G00919147Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    11. Using SST and a hammer, drive in the oil seal.
      1. SST 09950-60010 (09951-00390), 09950-70010 (09951-07100)
      NOTE: Make sure to install the oil seal facing in the correct direction.
    12. Lightly mount the control valve assembly between aluminum plates in a vise.
    13. To prevent oil seal lip damage, wind vinyl tape on the pinion part of the control valve shaft.
      Fig 38: Using SST And Hammer
      G00919148Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    14. Using SST, torque the guide nut.
      1. SST 09631-20060
      2. Torque: 25 N.m (250 kgf.cm, 18 ft.lbf) 
      NOTE: Be careful not to damage the oil seal lip.
      Fig 39: Using SST
      G00919149Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    15. Using a punch and a hammer, stake the nut.
    16. Coat a new O-ring with power steering fluid, and install it to the valve housing.
      Fig 40: Installing O-Ring To Valve Housing
      G00919150Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    17. Apply molybdenum disulfide base grease for the needle roller baring inside the rack housing in the illustrated portion.
      1. Volume of grease applied: Approximately 2 g (0.07 oz) 
    18. Install the control valve assembly with the 2 bolts.
      1. Torque: 18 N.m (184 kgf.cm, 13 ft.lbf) 
      Fig 41: Identifying Grease Filling
      G00919151Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  44. INSTALL RACK GUIDE 
    1. Install the rack guide and spring.
    2. Apply sealant to 2 or 3 threads of the rack guide spring cap.
      1. Sealant: Part No. 08833-00080, THREE BOND 1344, LOCTITE 242 or equivalent 
    3. Using a hexagon wrench (24 mm), temporarily install the spring cap.
      Fig 42: Installing Rack Guide
      G00919152Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  45. ADJUST TOTAL PRELOAD 
    1. To prevent the steering rack teeth from damaging the oil seal lip, temporarily install the RH and LH rack ends.
    2. Using a hexagon wrench (24 mm), tighten the rack guide spring cap.
      1. Torque: 25 N.m (250 kgf.cm, 18 ft.lbf) 
    3. Return the cap 30°.
      Fig 43: Adjusting Total Preload
      G00919153Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Using SST, turn the control valve shaft right and left 1 or 2 times.
      1. SST 09616-00011
    5. Using a hexagon wrench (24 mm), loosen the cap until the rack guide spring is not functioning.
      Fig 44: Loosening Cap
      G00919154Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Using SST, a torque wrench and a hexagon wrench (24 mm), tighten the cap until the preload is within specification.
      Fig 45: Tightening Cap
      G00919155Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. SST 09616-00011
      2. Preload (turning): 0.7 - 1.5 N.m (7.1 - 15.1 kgf.cm, 6.2 - 13.3 in.lbf) 
      NOTE: Adjustment should be done in the tightening direction of the spring cap.
    7. Apply sealant to 2 or 3 threads of the lock nut.
      1. Sealant: Part No. 08833-00080, THREE BOND 1344, LOCTITE 242 or equivalent 
    8. Temporarily install the lock nut.
    9. Using a hexagon wrench (24 mm), holding the rack guide spring cap rotating, and using SST, torque the nut.
      1. SST 09922-10010
      2. Torque: 65 N.m (660 kgf.cm, 48 ft.lbf) for use with SST 
      NOTE: Use SST 09922-10010 in the direction shown in the illustration.

      HINT:

      Use a torque wrench with a fulcrum length of 345 mm (13.58 in.).

      Fig 46: Measuring Fulcrum Length
      G00919156Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    10. Recheck the total preload.
      1. Preload (turning): 0.7 - 1.5 N.m (7.1 - 15.1 kgf.cm, 6.2 - 13.3 in.lbf) 
    11. Remove the RH and LH rack ends.
      Fig 47: Rechecking Total Preload
      G00919157Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  46. INSPECT POWER STEERING RACK 
    1. Insert a wire into the vent hole of the steering rack by 30 mm (1.18 in.), and ensure that the vent hole is not clogged with grease.

    HINT:

    If the hole is clogged, the pressure inside the boot will change after it is assembled and the steering wheel is turned.

    Fig 48: Inspecting Power Steering Rack
    G00919158Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  47. INSTALL STEERING RACK END SUB-ASSY 
    1. Install a new claw washer, and temporarily tighten the rack end.

      HINT:

      Align the claws of the washer with the steering rack grooves.

    2. Using SST to hold the steering rack steady, and using another SST, torque the rack end LH.
      Fig 49: Installing Steering Rack End Sub-Assy
      G00919159Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. SST 09922-10010
      2. Torque: 98 N.m (1,000 kgf.cm, 72 ft.lbf) for use with SST 
      NOTE: Use SST 09922-10010 in the direction shown in the illustration.

      HINT:

      Use a torque wrench with a fulcrum length of 380 mm (14.9 in.)

    3. Using SST to hold the rack end LH steady, and using another SST, torque the rack end RH.
      1. SST 09922-10010
      2. Torque: 98 N.m (1,000 kgf.cm, 72 ft.lbf) for use with SST 
      NOTE: Use SST 09922-10010 in the direction shown in the illustration.

      HINT:

      Use a torque wrench with a fulcrum length of 380 mm (14.9 in.).

      Fig 50: Measuring Fulcrum Length
      G00919160Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Using a brass bar and a hammer, stake the washer.
      NOTE: Avoid any impact to the rack.
    5. Employ the same manner described above to the other side.
    Fig 51: Identifying Brass Bar
    G00919161Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  48. INSTALL STEERING RACK BOOT LH 
    1. Install the boot.
    NOTE: Be careful not to damage or twist the boot.
  49. INSTALL STEERING RACK BOOT RH 

    HINT:

    Install the RH side by the same procedures with the LH side.

  50. INSTALL STEERING RACK BOOT CLAMP LH 
    1. Using pliers and a screwdriver, install the clamp.
      Fig 52: Installing Steering Rack Boot Clamp
      G00919162Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  51. INSTALL STEERING RACK BOOT CLAMP RH 

    HINT:

    Install the RH side by the same procedures with the LH side.

  52. INSTALL STEERING RACK BOOT CLIP LH 
    1. Using pliers, install the clip.
  53. INSTALL STEERING RACK BOOT CLIP RH 

    HINT:

    Install the RH side by the same procedures with the LH side.

  54. INSPECT POWER STEERING GEAR ASSY 
    1. Using SST, check that the rack boot stretches smoothly when the control valve shaft is being rotated.
      1. SST 09616-00011
      Fig 53: Inspecting Power Steering Gear Assy
      G00919163Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Apply MP grease in the illustrated portion.
    3. Install the dust cover.
      Fig 54: Installing Dust Cover
      G00919164Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  55. INSTALL STEERING TURN PRESSURE TUBE 
    1. Using SST, install the 2 turn pressure tubes.
      1. SST 09023-38200
      2. Torque: 23 N.m (230 kgf.cm, 17 ft.lbf) for use with SST 

    HINT:

    • Use a torque wrench with a fulcrum length of 345 mm (13.58 in.).
    • This torque value is effective in case that SST is parallel to a torque wrench.
    Fig 55: Installing Steering Turn Pressure Tube
    G00919165Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  56. INSTALL TIE ROD END SUB-ASSY LH 
    1. Screw the lock nut and tie rod end onto the rack end until the matchmarks are aligned.
    2. After adjusting toe-in, torque the nut.
      1. Torque: 88 N.m (897 kgf.cm, 65 ft.lbf) 
  57. INSTALL TIE ROD END SUB-ASSY RH 

    HINT:

    Install the RH side by the same procedures with the LH side.

  58. INSTALL POWER STEERING LINK ASSY 
    1. Install the power steering link assy with the 2 bolts and 2 nuts.
      1. Torque: 100 N.m (1,020 kgf.cm, 74 ft.lbf) 
    NOTE: The nut has a detent, so never turn the nut, be sure to turn the bolt.

    HINT:

    Insert the bolt and slide it with the gear assy as a unit and then install the bolt on the frame.

    Fig 56: Installing Power Steering Link Assy
    G00919166Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  59. INSTALL STABILIZER BAR FRONT (See  STABILIZER BAR  ) 
  60. STABILIZE SUSPENSION (See  STABILIZER BAR  ) 
  61. CONNECT STEERING GEAR OUTLET RETURN TUBE 
    1. Using SST, connect the outlet return tube.
      1. SST 09023-12700
      2. Torque: 42 N.m (420 kgf.cm, 31 ft.lbf) for use with SST 

      HINT:

      • Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
      • This torque value is effective in case that SST is parallel to a torque wrench.
      Fig 57: Measuring Fulcrum Length
      G00919167Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the hose with the clip.
      Fig 58: Installing Hose With Clip
      G00919168Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  62. CONNECT PRESSURE FEED TUBE ASSY 
    1. Install the pressure feed tube assy to the frame sub-assy with the 2 bolts.
      1. Torque: 28 N.m (286 kgf.cm, 21 ft.lbf) 
      Fig 59: Connecting Pressure Feed Tube Assy
      G00919169Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using SST, tighten the flare nut and connect the pressure feed tube.
      1. SST 09023-12700
      2. Torque: 42 N.m (420 kgf.cm, 31 ft.lbf) for use with SST 

    HINT:

    • Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
    • This torque value is effective in case that SST is parallel to a torque wrench.
    Fig 60: Measuring Fulcrum Length
    G00919170Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  63. FULLY TIGHTEN STEERING INTERMEDIATE SHAFT NO.2 (See  OVERHAUL  ) 
  64. CONNECT TIE ROD END SUB-ASSY LH 
    1. Connect the tie rod end to the steering knuckle arm.
    2. Install the nut and cotter pin.
      1. Torque: 91 N.m (928 kgf.cm, 67 ft.lbf) 
  65. CONNECT TIE ROD END SUB-ASSY RH 

    HINT:

    Install the RH side by the same procedures with the LH side.

  66. INSTALL ENGINE UNDER COVER SUB-ASSY NO.1 
  67. INSTALL ENGINE UNDER COVER ASSY REAR 
    1. Install the engine under cover assy rear with the 6 bolts.
  68. INSTALL FRONT WHEEL 
    1. Torque: 112 N.m (1,142 kgf.cm, 83 ft.lbf) 
  69. PLACE FRONT WHEELS FACING STRAIGHT AHEAD (See  OVERHAUL  ) 
  70. INSTALL TURN SIGNAL SWITCH ASSY (See  OVERHAUL  ) 
  71. INSTALL SPIRAL CABLE SUB-ASSY (See  OVERHAUL  ) 
  72. INSTALL STEERING COLUMN COVER LWR (See  OVERHAUL  ) 
  73. CENTER SPIRAL CABLE (See  OVERHAUL  ) 
  74. INSTALL STEERING WHEEL ASSY (See  OVERHAUL  ) 
  75. INSPECT STEERING WHEEL CENTER POINT (See  OVERHAUL  ) 
  76. INSTALL HORN BUTTON ASSY 
  77. INSPECT HORN BUTTON ASSY 
  78. INSPECT SRS WARNING LIGHT (See  AIR BAG WARNING LIGHT INTERMITTENT  ) 
  79. ADD POWER STEERING FLUID 
  80. BLEED POWER STEERING FLUID (  ON-VEHICLE INSPECTION  ) 
  81. CHECK POWER STEERING FLUID LEAKAGE (  ON-VEHICLE INSPECTION  ) 
  82. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT (See  FRONT WHEEL ALIGNMENT  )