LEMON Manuals: Even more car manuals for everyone

On-Vehicle Inspection

WARNING: This page is about a different car, the 2005 Toyota 4Runner. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK FUEL PUMP OPERATION AND FUEL LEAK 
    1. When using the hand-held tester
      1. Connect the hand-held tester to the DLC3.
      2. Turn the ignition switch ON and hand-held tester main switch ON.
        NOTE: Do not start the engine.
      3. Select the ACTIVE TEST mode on the hand-held tester.
      4. Please refer to the hand-held tester operator's manual for further details.
    2. When not using hand-held tester
      1. Remove the circuit opening relay.
      2. Using a service wire, connect terminals FP and +B of the relay block.
        NOTE: Pay due attention to the terminal connecting position to avoid a malfunction.
      3. Turn the ignition switch ON, and check that the fuel pump operates.
      NOTE: Do not start the engine.
    3. Check that there are no fuel leaks after doing maintenance anywhere on the fuel system.
      Fig 1: Connecting Terminals FP And +B Of Relay Block
      G02578196Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Check that the pulsation damper screw rises up when the fuel pump operates.

      If operation is not as specified, check the following parts:

      • Fusible link
      • Fuses
      • EFI main relay
      • Fuel pump
      • ECM
      • Wiring connections
        Fig 2: Removing Screw
        G02578197Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Turn the ignition switch OFF.
    6. Disconnect the hand-held tester from the DLC3.
  2. CHECK FUEL PRESSURE 
    1. Check the battery positive voltage is above 12 V.
    2. Disconnect the negative (-) terminal cable from the battery.
    3. Remove the front fuel pipe from the LH delivery pipe (See REPLACEMENT ).
    4. Install the front fuel pipe and SST (pressure gauge) to the delivery pipe with the 3 gaskets and another SST (adaptor).

      SST 09268-45014 (09268-41200, 09268-41190, 90405-06167, 09268-41210, 90467-11009)

      Torque: 39 N.m (400 kgf.cm, 29 ft.lbf) 

    5. Wipe off any splattered gasoline.
    6. Reconnect the negative (-) terminal cable to the battery.
    7. Connect the hand-held tester to the DLC3 (See step 1 in check fuel pump operation).
      Fig 3: Installing Front Fuel Pipe Using SST
      G02578198Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    8. Measure the fuel pressure.

      Fuel pressure: 265 to 304 kPa (2.7 to 3.1 kgf/cm 2  , 38 to 44 psi) 

      If pressure is high, replace the fuel pressure regulator.

      If pressure is low, check the following parts:

      • Fuel hoses and connections
      • Fuel pump
      • Fuel filter
      • Fuel pressure regulator
    9. Disconnect the hand-held tester from the DLC3.
    10. Start the engine.
    11. Measure the fuel pressure at idle.

      Fuel pressure: 265 to 304 kPa (2.7 to 3.1 kgf/cm 2  , 38 to 44 psi) 

    12. Stop the engine.
    13. Check that the fuel pressure remains as specified for 5 minutes after the engine has stopped.

      Fuel pressure: 147 kPa (1.5 kgf/cm 2  , 21 psi) or more 

      If pressure is not as specified, check the fuel pump, pressure regulator and/or injectors.

    14. After checking the fuel pressure, disconnect the negative (-) terminal cable from the battery and carefully remove the SST to prevent gasoline from splashing.

      SST 09268-45014 (09268-41200, 09268-41190, 90405-06167, 09268-41210, 09467-11009)

    15. Reinstall the front fuel pipe to the LH delivery pipe (See REPLACEMENT ).
    16. Reconnect the negative (-) terminal cable to the battery.
    17. Check for fuel leaks (See step 1 in check fuel pump operation).