LEMON Manuals: Even more car manuals for everyone

Fuel Injector ASSY (1GR-FE): Replacement

WARNING: This page is about a different car, the 2005 Toyota 4Runner. However, it is still accessible from the selected car via links, so may be relevant.
  1. WORK FOR PREVENTING GASOLINE FROM SPILLING OUT (See  FUEL SYSTEM (1GR-FE)  ) 
  2. DRAIN ENGINE  COOLANT (1 GR-FE) 
  3. REMOVE V-BANK COVER (See  REPLACEMENT  ) 
  4. DISCONNECT VENTILATION HOSE NO.2 
  5. REMOVE AIR CLEANER ASSY (See  REPLACEMENT  ) 
    Fig 1: Disconnecting Ventilation Hose No.2
    G02578124Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. DISCONNECT WATER BYPASS HOSE NO.5 
    Fig 2: Disconnecting Water By-Pass Hose No.5
    G02578125Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. DISCONNECT WATER BYPASS HOSE NO.4 
    Fig 3: Disconnecting Water By-Pass Hose No.4
    G02578126Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. DISCONNECT FUEL VAPOR FEED HOSE ASSY 
    Fig 4: Disconnecting Fuel Vapor Feed Hose Assy
    G02578127Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. DISCONNECT VENTILATION HOSE 
    Fig 5: Disconnecting Ventilation Hose
    G02578128Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. REMOVE INTAKE AIR SURGE TANK 
    1. Disconnect the 2 VSV connectors.
    2. Disconnect the throttle motor connector.
    3. Remove the 3 wire harness clamps and hose clamp.
      Fig 6: Disconnecting VSV Connectors
      G02578129Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Remove the 3 upper bolts which are used to secure the 2 surge tank stays and throttle body bracket.
      Fig 7: Removing Upper Bolts And Throttle Body Bracket
      G02578130Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Using the socket hexagon wrench 8, remove the 4 bolts.
    6. Remove the 2 nuts, intake air surge tank and gasket.
      Fig 8: Removing Nuts And Intake Air Surge Tank
      G02578131Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. DISCONNECT FUEL PIPE SUB-ASSY NO.1 
    1. Remove the fuel pipe clamp.
    2. Pinch the tube connector then pull out the fuel pipe.
    NOTE:
    • Check if there is any dirt like mud around the connector before this work, because the quick connector has the O-ring to seal the fuel pipe and fuel delivery pipe. Clean dirt away if necessary.
    • Do not use any tool in this work.
    • Do not bend or twist the nylon tube.
      Fig 9: Removing Fuel Pipe Clamp
      G02578132Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    • Keep off plug from foreign objects.
    • To protect the fuel pipe, cover it with a vinyl bag after checking.
    • When the fuel pipe and fuel delivery pipe are stuck, pinch the nylon tube with fingers, and turn it carefully to free and then disconnect the fuel pipe.
    Fig 10: Identifying Quick Connector Components
    G02578133Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. DISCONNECT FUEL PIPE SUB-ASSY NO.2 
    1. Remove the fuel pipe clamp.
    2. Pinch the tube connector then pull out the fuel pipe.
    NOTE:
    • Check if there is any dirt like mud around the connector before this work, because the quick connector has the O-ring to seal the fuel pipe and fuel delivery pipe. Clean dirt away if necessary.
    • Do not use any tool in this work.
      Fig 11: Pulling Out Fuel Pipe
      G02578134Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    • Do not bend or twist the nylon tube.
    • Keep off plug from foreign objects.
    • To protect the fuel pipe, cover it with a vinyl bag after checking.
    • When the fuel pipe and fuel pressure regulator are stuck, pinch the nylon tube with fingers, and turn it carefully to free and then disconnect the fuel pipe.
    Fig 12: Identifying Quick Connector Components
    G02578135Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. REMOVE FUEL DELIVERY PIPE SUB-ASSY 
    1. Disconnect the 6 fuel injector connectors.
    2. Remove the 6 bolts and fuel delivery pipe together with the 6 fuel injectors.
    NOTE: Be careful not to drop the injectors when removing the fuel delivery pipe.
    Fig 13: Disconnecting Fuel Injector Connectors
    G02578136Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  14. REMOVE FUEL INJECTOR ASSY 
    Fig 14: Removing Fuel Injector Assy
    G02578137Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. INSTALL FUEL INJECTOR ASSY 
    1. Install a new insulator to the each fuel injector.
    2. Apply a light coat of spindle oil or gasoline to a new O-ring and install it to the each fuel injector.
      Fig 15: Installing Insulator To Fuel Injector
      G02578138Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. While turning the fuel injector left and right, install it to the fuel delivery pipe.
    4. Position the fuel injector connector outward.
      Fig 16: Positioning Fuel Injector Connector
      G02578139Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  16. INSTALL FUEL DELIVERY PIPE SUB-ASSY 
    1. Place the fuel delivery pipe together with the 6 fuel injectors on the intake manifold.
    2. Temporarily install the 6 bolts which are used to hold the fuel delivery pipe to the intake manifold.
    3. Check that the fuel injectors rotate smoothly.

      HINT:

      If fuel injectors do not rotate smoothly, the probable cause is incorrect installation of O-rings. Replace an O-ring.

    4. Position the fuel injector connector outward.
      Fig 17: Identifying Connector
      G02578140Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Tighten the 6 bolts which are used to hold the fuel delivery pipe to the intake manifold.

      Torque: 15 N.m (153 kgf.cm, 11 ft.lbf) 

    6. Connect the 6 fuel injector connectors.
  17. CONNECT FUEL PIPE SUB-ASSY NO.2 
    1. Push in the tube connector to the pipe then tube connector makes "click" sound.
      NOTE:
      • Check if there is any damage or foreign objects on the connected part of the fuel pipe.
      • After connecting, check if the pipe and connector are securely connected by pulling them.
    2. Install the fuel pipe clamp.
  18. CONNECT FUEL PIPE SUB-ASSY NO.1 
    1. Push in the tube connector to the pipe then tube connector makes "click" sound.
      NOTE:
      • Check if there is any damage or foreign objects on the connected part of the fuel pipe.
      • After connecting, check if the pipe and connector are securely connected by pulling them.
    2. Install the fuel pipe clamp.
  19. INSTALL INTAKE AIR SURGE TANK 
    1. Install a new gasket and the intake air surge tank with the 2 nuts.

      Torque: 28 N.m (286 kgf.cm, 21 ft.lbf) 

    2. Using the socket hexagon wrench 8, install the 4 bolts.

      Torque: 28 N.m (286 kgf.cm, 21 ft.lbf) 

    3. Install the 3 upper bolts which are used to secure the 2 surge tank stays and throttle body bracket.

      Torque: 21 N.m (214 kgf.cm, 16 ft.lbf) 

    4. Install the 3 wire harness clamps and hose clamp.
    5. Connect the throttle motor connector.
    6. Connect the 2 VSV connectors.
  20. CONNECT VENTILATION HOSE 
  21. CONNECT FUEL VAPOR FEED HOSE ASSY 
  22. CONNECT WATER BYPASS HOSE NO.4 
  23. CONNECT WATER BYPASS HOSE NO.5 
  24. INSTALL AIR CLEANER ASSY (See  REPLACEMENT  ) 
  25. CONNECT VENTILATION HOSE NO.2 
  26. INSTALL V-BANK COVER (See  REPLACEMENT  ) 
  27. ADD ENGINE  COOLANT (1 GR-FE) 
  28. CHECK FOR ENGINE COOLANT LEAKS (See  COOLING SYSTEM (1 GR-FE)  ) 
  29. CHECK FOR FUEL LEAKS (See  ON-VEHICLE INSPECTION  )