LEMON Manuals: Even more car manuals for everyone

DTC Index

NOTE: Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the manufacturer-approved diagnostic system).
Intermittent faults may cause DTCs to be logged, however some DTCs may be cleared during an ignition off, ignition on cycle. Carry out a road test (if safe to do so), check the functionality of the system and retrieve any DTCs before  turning the ignition off.
DTC Description Possible Causes Action
B1C3173 Steering Column Motor Relay
  • Software error (electric column not installed)
  • Steering column motor relay fault (stuck on)
Where an electric column adjustment is not installed, no action necessary, clear/ignore DTC. Where an electric column adjustment is installed, refer to the electrical guides and check the column motor circuit for short or open circuit and check/renew the memory control module as necessary
B1C3193 Steering Column Motor Relay
  • Software error (electric column not installed)
  • Memory control module internal relay fault (inoperative)
Where an electric column adjustment is not installed, no action necessary, clear/ignore DTC. Where an electric column adjustment is installed, check/renew the control module as necessary
B1C3213 Steering Column Tilt Solenoid
  • Software error (electric column not installed)
  • Steering column motor tilt solenoid open load
Where an electric column adjustment is not installed, no action necessary, clear/ignore DTC. Where an electric column adjustment is installed, refer to the electrical guides and check the column tilt solenoid circuit for short or open circuit and check/renew the tilt solenoid as necessary
B1C3296 Steering Column Tilt Solenoid
  • Software error (electric column not installed)
  • Steering column motor tilt solenoid thermal overload
Where an electric column adjustment is not installed, no action necessary, clear/ignore DTC. Where an electric column adjustment is installed, refer to the electrical guides and check the column tilt solenoid circuit for short or open circuit. Check for other relevant DTCs and repair as necessary. Allow the solenoid to cool, clear the DTC and check the solenoid/tilt function operation. If the DTC persists renew the tilt solenoid as necessary
B1C333A Steering Column Tilt Feedback Signal
  • Software error (electric column not installed)
  • Steering column tilt motor moved beyond expected range
  • Sensor circuit open or short circuit
  • Motor position sensor fault
Where an electric column adjustment is not installed, no action necessary, clear/ignore DTC. Where an electric column adjustment is installed, refer to the electrical guides and check the column tilt solenoid feedback circuit for short or open circuit. Check the solenoid/tilt function operation and range of movement. Renew the tilt solenoid as necessary
B1C3413 Steering Column Telescopic Solenoid
  • Software error (electric column not installed)
  • Steering column motor telescopic solenoid open load
Where an electric column adjustment is not installed, no action necessary, clear/ignore DTC. Where an electric column adjustment is installed, refer to the electrical guides and check the column telescopic solenoid circuit for short or open circuit and check/renew the tilt solenoid as necessary
B1C3496 Steering Column Telescopic Solenoid
  • Software error (electric column not installed)
  • Steering column motor telescopic solenoid thermal overload
Where an electric column adjustment is not installed, no action necessary, clear/ignore DTC. Where an electric column adjustment is installed, refer to the electrical guides and check the column telescopic solenoid circuit for short or open circuit. Check for other relevant DTCs and repair as necessary. Allow the solenoid to cool, clear the DTC and check the solenoid/telescopic function operation. If the DTC persists renew the telescopic solenoid as necessary
B1C353A Steering Column Telescopic Feedback Signal
  • Software error (electric column not installed)
  • Steering column telescopic motor moved beyond expected range
  • Sensor circuit open or short circuit
  • Motor position sensor fault
Where an electric column adjustment is not installed, no action necessary, clear/ignore DTC. Where an electric column adjustment is installed, refer to the electrical guides and check the column telescopic solenoid feedback circuit for short or open circuit. Check the solenoid/telescopic function operation and range of movement. Renew the telescopic solenoid as necessary
B1C363A Steering Column Tilt/Telescope Switch
  • Software error (electric column not installed)
  • Steering column tilt/telescopic switch voltage beyond expected range
  • Sensor circuit open or short circuit
  • Switch fault
Where an electric column adjustment is not installed, no action necessary, clear/ignore DTC. Where an electric column adjustment is installed, refer to the electrical guides and check the column tilt/telescopic switch circuit for short or open circuit. Check the tilt/telescopic switch operation and renew the switch as necessary
C005104 Steering Wheel Position Sensor
  • System internal failure
  • Harness/connector issue
Check the steering angle sensor, connector and circuits. Refer to the electrical guides
C005162 Steering Wheel Position Sensor
  • Signal compare failure
  • Harness/connector issue
Check the steering angle sensor, connector and circuits. Refer to the electrical guides
C005164 Steering Wheel Position Sensor
  • Signal plausibility failure
  • Harness/connector issue
Check the steering angle sensor, connector and circuits. Refer to the electrical guides
C112201 Steering Isolation Valve
  • Servotronic steering valve circuit high resistance
  • Servotronic steering valve circuit short circuit to ground
  • Servotronic steering valve fault
Refer to the guided diagnostic routine for this code on the approved diagnostic system
C11231C Steering Isolation Valve Supply Circuit
  • Servotronic steering valve supply circuit high resistance
  • Servotronic steering valve supply circuit short circuit to ground
  • Servotronic steering valve supply circuit short circuit to power
  • Servotronic steering valve fault
Refer to the guided diagnostic routine for this code on the approved diagnostic system
C1B1862 Supply Voltage X-Ref Check
  • Inconsistent battery voltages received by air suspension control module
  • Air suspension control module supply circuit short circuit to ground
  • Air suspension control module supply circuit high resistance
  • Air suspension control module failure
Refer to the guided diagnostic routine for this code on the approved diagnostic system. Refer to the warranty policy and procedures manual if a module is suspect
U007388 Control Module Communication Bus 'A' Off
  • CAN bus off
Refer to the Network Communications information
U012287 Lost Communication With Vehicle Dynamics Control Module
  • CAN module status signals not received from the VDM in the specified time
Check for ABS DTCs. Refer to the Network Communications information
U012687 Lost Communication With Steering Angle Sensor Module
  • CAN bus fault
  • Steering angle sensor module disconnected
  • Steering angle sensor module not configured
  • Steering angle sensor module failure
  • Harness/connector issue
Check the control module installation/configuration. Refer to the Network Communications information
U030055 Internal Control Module Software Incompatibility
  • Software incompatibility with ATCM
  • Not configured
Configure the modules using the approved diagnostic system. Refer to the Network Communications information
U041686 Invalid Data Received From Vehicle Dynamics Control Module
  • ABS fault
Check for dynamic suspension/ABS DTCs. Refer to the relevant information.
U1A1449 CAN Initialization Failure
  • Internal electronic fault
Configure the steering angle sensor module using the approved diagnostic system. Refer to the Network Communications information.
U300262 Vehicle Identification Number
  • Signal compare failure
Program the module using the approved diagnostic system