LEMON Manuals: Even more car manuals for everyone

Repair Procedures: Replacement

WARNING: This page is about a different car, the 2019 Kia Stinger. However, it is still accessible from the selected car via links, so may be relevant.
  1. Disconnect the negative (-) battery terminal.
  2. Recover the refrigerant with a recovery/recycling/charging station.
  3. When the engine is cool, drain the engine coolant from the radiator.

    G 2.0 T-GDI THETA (Refer to " COOLANT  ") 

    G 3.3 T-GDI LAMBDA (Refer to " COOLANT  ") 

  4. Remove the cowl top cover.

    (Refer to " COWL TOP COVER  ") 

  5. Remove the engine room partition.
  6. Remove the expansion valve (A) from the evaporator core after loosening the bolts.

    Tightening torque:  7.8 - 11.7 N.m (0.8 - 1.2 kgf.m, 5.8 - 8.7 lb.ft)

    G12799165Courtesy of KIA MOTORS AMERICA, INC.
    NOTE:
    • Plug or cap the lines immediately after disconnecting them to avoid moisture and dust contamination.
    • When installing, replace with a new O-ring (B).
  7. Disconnect the heater hoses (A).
    G12799166Courtesy of KIA MOTORS AMERICA, INC.
    CAUTION: Engine coolant will run out when the hoses are disconnected; drain it into a clean drip pan. Be sure not to let coolant spill on electrical parts or painted surfaces. If any coolant spills, rinse it off immediately.
  8. Loosen the cowl cross member mounting bolts (A).
    G12799167Courtesy of KIA MOTORS AMERICA, INC.
  9. Remove both sides of front seat assembly.

    (Refer to " FRONT SEAT ASSEMBLY  ") 

  10. Remove the floor console.

    (Refer to " FLOOR CONSOLE ASSEMBLY  ") 

  11. Remove both sides of the front pillar trim.

    (Refer to " FRONT PILLAR TRIM  ") 

  12. Remove both sides of the cowl side trim.

    (Refer to " COWL SIDE TRIM  ") 

  13. Remove the crash pad lower panel.

    (Refer to " CRASH PAD LOWER PANEL  ") 

  14. Remove the steering column shroud lower panel.

    (Refer to " STEERING COLUMN SHROUD PANEL  ") 

  15. Remove the steering wheel.

    (Refer to " STEERING WHEEL  ") 

  16. Remove the multifunction switch.

    (Refer to " MULTIFUNCTION SWITCH  ") 

  17. Lower the steering column after loosening the mounting bolts.

    (Refer to " STEERING COLUMN AND SHAFT  ") 

  18. Remove the front door scuff trim.

    (Refer to " DOOR SCUFF TRIM  ") 

  19. Separate the accelerator pedal (A) after loosening the bolts.

    Tightening torque:  8.8 - 13.7 N.m (0.9 - 1.4 kgf.m, 6.5 - 10.1 lb.ft)

    G12799168Courtesy of KIA MOTORS AMERICA, INC.
  20. Remove the accelerator pedal after disconnecting the connector (A).
    G12799169Courtesy of KIA MOTORS AMERICA, INC.
  21. Separate the floor carpet (A) to allow space for removing the rear heating duct.
    G12799170Courtesy of KIA MOTORS AMERICA, INC.
  22. Remove the rear heating duct (A) after loosening the clip.
    G12799171Courtesy of KIA MOTORS AMERICA, INC.
  23. Disconnect the shift lever connector (A).
    G12799172Courtesy of KIA MOTORS AMERICA, INC.
  24. Disconnect the airbag control module (SRSCM) connector (A).
    G12799173Courtesy of KIA MOTORS AMERICA, INC.
  25. Disconnect the passenger compartment junction box connectors (A).
    G12799174Courtesy of KIA MOTORS AMERICA, INC.
  26. Disconnect the multi box connectors (A).

    [LH] 

    G12799175Courtesy of KIA MOTORS AMERICA, INC.

    [RH] 

    G12799176Courtesy of KIA MOTORS AMERICA, INC.
  27. Disconnect the connector (A) and the mounting clips in the front pillar.

    [LH] 

    G12799177Courtesy of KIA MOTORS AMERICA, INC.

    [RH] 

    G12799178Courtesy of KIA MOTORS AMERICA, INC.
  28. Remove the drain hose (A).
    G12799179Courtesy of KIA MOTORS AMERICA, INC.
  29. After loosening the nuts and bolts, remove the main crash pad and cowl cross bar assembly (A) altogether.

    [LH] 

    G12799180Courtesy of KIA MOTORS AMERICA, INC.

    [RH] 

    G12799181Courtesy of KIA MOTORS AMERICA, INC.
  30. Remove the integrated body control unit.

    (Refer to " INTEGRATED BODY CONTROL UNIT (IBU)  ") 

  31. Disconnect the heater & blower unit connectors.
    1. Disconnect the temperature control actuator (A) and mode control actuator (B) connectors, and then remove the wiring mounting clips.
    2. Disconnect the console temperature sensor (C), console ON/OFF actuator (D) connectors and then remove the wiring mounting clips.
      G12799182Courtesy of KIA MOTORS AMERICA, INC.
      G12799183Courtesy of KIA MOTORS AMERICA, INC.
    3. Disconnect the evaporator temperature sensor (A), temperature control actuator (B) and auto defogging actuator (C) connectors, and then remove the wiring mounting clips.
      G12799184Courtesy of KIA MOTORS AMERICA, INC.
    4. Disconnect the intake actuator (A), heater control unit (B) and FET (C) connectos, and then remove the wiring mounting clips.
      G12799185Courtesy of KIA MOTORS AMERICA, INC.
    5. Disconnect the blower motor connector (A) and then remove the wiring mounting clips.
      G12799186Courtesy of KIA MOTORS AMERICA, INC.
    6. Disconnect the PTC heater connector (A).
    G12799187Courtesy of KIA MOTORS AMERICA, INC.
  32. Remove the heater and blower unit (A) from the crash pad after loosening the mounting nuts.
    G12799188Courtesy of KIA MOTORS AMERICA, INC.
  33. Remove the heater core cover (A).
    G12799189Courtesy of KIA MOTORS AMERICA, INC.
    G12799190Courtesy of KIA MOTORS AMERICA, INC.
  34. Separate the blower unit (B) from the heater unit (A) after loosening the screws.
    G12799191Courtesy of KIA MOTORS AMERICA, INC.
    G12799192Courtesy of KIA MOTORS AMERICA, INC.
    G12799193Courtesy of KIA MOTORS AMERICA, INC.
  35. Install in the reverse order of removal.