LEMON Manuals: Even more car manuals for everyone

Repair Procedures: Removal

WARNING: This page is about a different variant/trim than selected.
  1. Remove the air cleaner assembly.

    (Refer to Engine Mechanical System - " AIR CLEANER  ") 

  2. Remove the battery and battery tray.

    (Refer to Engine Electrical System - " BATTERY  ") 

  3. Disconnect the back up lamp switch (A).
    G12576845Courtesy of KIA MOTORS AMERICA, INC.
  4. Remove the wiring from the bracket (A).
    G12576846Courtesy of KIA MOTORS AMERICA, INC.
  5. Remove the control cable.
    1. Remove the control cable from the control shaft after removing the pins (A).
    2. Loosen the control cable bracket bolts (B).

      Tightening torque: 

      14.7 - 21.6 N.m (1.5 - 2.2 kgf.m, 10.8 - 15.9 lb.ft)

    G12576847Courtesy of KIA MOTORS AMERICA, INC.
  6. Remove the ground bolt (A) and clutch tube bracket bolt (B).

    Tightening torque: 

    1. 26.5 - 32.4 N.m (2.7 - 3.3 kgf.m, 19.5 - 23.9 lb.ft)
    2. 14.7 - 21.6 N.m (1.5 - 2.2 kgf.m, 10.8 - 15.9 lb.ft)
    G12576848Courtesy of KIA MOTORS AMERICA, INC.
  7. Remove the CKP sensor (A) after removing a bolt.[Gasoline 1.4 only]

    Tightening torque: 

    9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb.ft)

    G12576849Courtesy of KIA MOTORS AMERICA, INC.
  8. Loosen the starter mounting bolts (A) and the transaxle mounting bolts (B).

    Tightening torque: 

    1. 49.0 - 63.7 N.m (5.0 - 6.5 kgf.m, 36.2 - 47.0 lb.ft)
    2. 42.2 - 54.0 N.m (4.3 - 5.5 kgf.m, 31.1 - 39.8 lb.ft)
    G12576850Courtesy of KIA MOTORS AMERICA, INC.
  9. Install the engine support fixture on the engine room.
    1. Loosen the bolts (6-pcs).
      G12576851Courtesy of KIA MOTORS AMERICA, INC.
    2. Assemble the engine support fixture on the engine room.

      (Refer to Special Service Tools - " ENGINE SUPPORT FIXTURE ASSEMBLY DRAWING  ") 

      G12576852Courtesy of KIA MOTORS AMERICA, INC.
  10. Support the transaxle safely on a jack.
    G12576853Courtesy of KIA MOTORS AMERICA, INC.
  11. Remove the cover (A).
    G12576854Courtesy of KIA MOTORS AMERICA, INC.
  12. Remove the transaxle mounting bracket bolts (A).

    Tightening torque: 

    88.3 - 107.9 N.m (9.0 - 11.0 kgf.m, 65.1 - 79.8 lb.ft)

    G12576855Courtesy of KIA MOTORS AMERICA, INC.
  13. Remove the transaxle support bracket (A).

    Tightening torque: 

    58.8 - 78.5 N.m (6.0 - 8.0 kgf.m, 43.4 - 57.9 lb.ft)

    G12576856Courtesy of KIA MOTORS AMERICA, INC.
  14. Remove the under cover.

    (Refer to Engine Mechanical System - " ENGINE ROOM UNDER COVER  ") 

  15. Remove the drive shaft assembly.

    (Refer to Driveshaft and Axle - " FRONT DRIVESHAFT  ") 

  16. Remove the exhaust manifold stay (A).

    Tightening torque: 

    39.2 - 49.0 N.m (4.0 - 5.0 kgf.m, 28.9 - 36.2 lb.ft)

    G12576857Courtesy of KIA MOTORS AMERICA, INC.
  17. Remove the clutch release cylinder assembly (B) after removing the nuts (A).

    Tightening torque: 

    14.7 - 21.6 N.m (1.5 - 2.2 kgf.m, 10.8 - 15.9 lb.ft)

    G12576858Courtesy of KIA MOTORS AMERICA, INC.
  18. Remove the roll rod bracket (C) after removing bolt (A, B).

    Tightening torque 

    1. 107.9 - 127.5 N.m (5.0 - 6.5 kgf.m, 79.6 - 94.0 lb.ft)
    2. 49.0 - 63.7 N.m (11.0 - 13.0 kgf.m, 36.2 - 47.0 lb.ft)
    G12576859Courtesy of KIA MOTORS AMERICA, INC.
  19. Remove the roll rod support bracket (A).

    Tightening torque: 

    49.0 - 68.6 N.m (5.0 - 7.0 kgf.m, 36.2 - 50.6 lb.ft)

    G12576860Courtesy of KIA MOTORS AMERICA, INC.
  20. Support the transaxle safely on a jack.
  21. Loosen the transaxle lower mounting bolts (A, B).

    Tightening torque: 

    1. 42.2 - 48.1 N.m (4.3 - 4.9 kgf.m, 31.1 - 35.4 lb.ft)
    2. 42.2 - 54.0 N.m (4.3 - 5.5 kgf.m, 31.1 - 39.8 lb.ft)
    G12576861Courtesy of KIA MOTORS AMERICA, INC.
  22. After separating the transaxle from the engine, remove the transaxle by lowering the jack slowly.
    NOTE: Be careful not to damage other nearby systems or parts when removing the transaxle assembly.