LEMON Manuals: Even more car manuals for everyone

Repair Procedures: Installation

  1. Install the crankshaft sprocket.
  2. Install the tensioner arm assembly (A) and the idler (B).

    Tightening torque 

    Tensioner arm bolt:

    34.3 ~ 53.9Nm (3.5 ~ 5.5kgf.m, 25.3~ 39.8lb-ft)

    Idler pulley bolt:

    49.0 ~ 58.8Nm (5.0 ~ 6.0kgf.m, 36.2~ 43.4lb-ft)

    Fig 1: Identifying Tensioner Arm Assembly And Idler
    G06415493Courtesy of KIA MOTORS AMERICA, INC.
  3. Ensure the timing marks on the camshaft and the crankshaft sprockets.
    Fig 2: Identifying Timing Marks On Camshaft And Crankshaft Sprockets
    G06415494Courtesy of KIA MOTORS AMERICA, INC.
  4. Install the timing belt.

    Crankshaft sprocket (A) → Idler (B) → Bank 2 exhaust camsprocket (C) → Water pump pulley (D) → Bank 1 exhaust camsprocket (E) → Tensioner pulley (F).

    Fig 3: Identifying Sprocket And Idler
    G06415495Courtesy of KIA MOTORS AMERICA, INC.
  5. Install the timing belt auto tensioner.
    1. Make the tensioner stand for about five minutes before installing.
    2. Press the rod with the weight, 150 ~ 200N.
    3. If the rod is stiff, insert a set-pin with pressing the rod slowly. If not, press the rod 2 ~ 3 times from the maximum length to 2.9mm (the position in which the two holes of the rod and the body can be at one).
    4. Check for stiffness. If there is, insert a set-pin and other wise, replace the auto-tensioner.
      Fig 4: Identifying Auto-Tensioner
      G06415496Courtesy of KIA MOTORS AMERICA, INC.
      NOTE:
      • Do not lay down the auto tensioner.
      • Do not compress the rod suddenly. Compress the rod with the wight less than 4000N.
      • When reinstalling the auto tensioner, ensure proper orientation.
      • Do not press the rod any more when its projection from the body is 2.5mm.
      • Keep the auto-tensioner stand at room temperature in winter.
    5. Install the auto tensioner (A) to the front case with the set-pin inserted.

      Tightening torque 

      19.6 ~ 26.5Nm (2.0 ~ 2.7kgf.m, 14.5 ~ 19.5lb-ft)

      Fig 5: Identifying Auto Tensioner
      G06415497Courtesy of KIA MOTORS AMERICA, INC.
  6. Remove the auto tensioner set-pin.
  7. Check the tension of the timing belt.
    1. Turn the crankshaft 2 revolutions clockwise, and set the number one cylinder to TDC.

      After 5 minutes, measure the length of the projected rod.

      Specification 

      5 ~ 7mm (0.1969 ~ 0.2756in.)

      Fig 6: Identifying Auto Tensioner Set-Pin
      G06415498Courtesy of KIA MOTORS AMERICA, INC.
    2. Ensure the locations of the timing marks for each sprocket.
  8. Install the engine support bracket (A).

    Tightening torque 

    58.8 ~ 68.6Nm (6.0 ~ 7.0kgf.m, 43.4 ~ 50.6lb-ft)

    Fig 7: Identifying Engine Support Bracket
    G06415499Courtesy of KIA MOTORS AMERICA, INC.
    CAUTION:
    • Check for the length of the bolts.(Upper-2EA/Lower-1EA).
    • Use a torque wrench by all means.
  9. Install the timing belt lower cover.

    Tightening torque 

    9.8 ~ 11.8Nm (1.0 ~ 1.2kgf.m, 7.8 ~ 8.7lb-ft)

    Fig 8: Identifying Timing Belt Lower Cover
    G06415500Courtesy of KIA MOTORS AMERICA, INC.
    NOTE: Align the holes of the bolts by pushing the left timing belt lower cover to left a little bit.
  10. Install the crankshaft damper pulley (A).

    Tightening torque 

    166.7 ~ 176.5Nm (17.0 ~ 18.0kgf.m, 123.0 ~ 130.2lb-ft)

    Fig 9: Identifying Crankshaft Damper Pulley
    G06415501Courtesy of KIA MOTORS AMERICA, INC.
  11. Install the engine mounting bracket (A).

    Tightening torque 

    63.7 ~ 83.4Nm (6.5 ~ 8.5kgf.m, 47.0 ~ 61.5lb-ft)

    Fig 10: Identifying Engine Mounting Bracket
    G06415502Courtesy of KIA MOTORS AMERICA, INC.
  12. Install the timing belt upper cover (A).

    Tightening torque 

    9.8 ~ 11.8Nm (1.0 ~ 1.2kgf.m, 7.2 ~ 8.7lb-ft)

    Fig 11: Identifying Timing Belt Upper Cover
    G06415503Courtesy of KIA MOTORS AMERICA, INC.
  13. Install the drive belt tensioner (C).

    Tightening torque 

    34.3 ~ 53.9Nm (3.5 ~ 5.5kgf.m, 25.3 ~ 39.8lb-ft)

  14. Install the drive belt idler and the drive belt (A).

    Tightening torque 

    34.3 ~ 53.9Nm (3.5 ~ 5.5kgf.m, 25.3 ~ 39.8lb-ft)

    Fig 12: Engine Drive Belt Routing Diagram
    G06415504Courtesy of KIA MOTORS AMERICA, INC.
  15. Install the right side cover.
  16. Install the front right wheel and tire.
  17. Install the engine cover (A).

    Tightening torque 

    7.8 ~ 11.8Nm (0.8 ~ 1.2kgf.m, 5.8 ~ 8.7lb-ft)

    Fig 13: Identifying Engine Cover Location
    G06415505Courtesy of KIA MOTORS AMERICA, INC.