LEMON Manuals: Even more car manuals for everyone

DTC P0101: Mass Airflow Sensor Range/Performance Problem: Procedure

NOTE: After any repair has been made, see AFTER-REPAIR PROCEDURE  under SELF DIAGNOSTIC SYSTEM.
  1. Check air cleaner. If air cleaner is dirty, replace air cleaner. If air cleaner is okay, go to next step.
  2. Check oil cap and oil dipstick installation. If problem exists, repair as necessary. If problem does not exist, go to next step.
  3. Check intake tube, breather hose and MAF sensor for air leaks. If problem exists, repair as necessary. If problem does not exist, go to next step.
    CAUTION: DO NOT spray carburetor cleaner on or near coils or plug wires. Allow enough time between checking areas for leaks for carburetor spray to dissipate.
  4. Backprobe and measure voltage between front Heated Oxygen Sensor (HO2S) harness connector terminal No. 2 (Tan wire) and ground. See Figure. Start engine and allow it to reach normal operating temperature. With engine idling, spray short spurts of aerosol carburetor cleaner into following areas while observing voltage changes at Tan wire:
    • Throttle body gasket.
    • Gasket between intake manifold and cylinder head.
    • Gasket between intake manifold and surge tank.
    • Seals between intake manifold and fuel injectors.
    • Seal between surge tank and PCV pipe.
    A long rise in voltage that corresponds to approximate timing and duration of spray of carburetor cleaner indicates air leak in area sprayed. If leak is indicated, repair as necessary. If leak is not indicated, go to next step.
  5. Disconnect MAF connector, see Figure. Check MAF sensor for contamination, deterioration or damage. If MAF sensor is okay, go to next step. If MAF sensor is contaminated, clean with aerosol brake cleaner and let air dry. Check air cleaner and housing for source of leak and repair as necessary. If MAF sensor is damaged or deteriorated, replace MAF sensor.
  6. Connect MAF harness connector. Start engine and allow it to reach normal operating temperature. Backprobe and measure voltage between ECM harness connector "D" terminal D14 (M/T) or ECM harness connector "C" terminal C8 (A/T) Blue wire (TP sensor signal) and ground. See Figure or Figure . See IDENTIFYING THROTTLE POSITION SENSOR-TO-ECM CIRCUITS  table. Measure voltage at idle and while accelerating engine up to 3000 RPM. At sea level and 50% relative humidity, voltage should be 0.3-0.9 volts at idle and increase linearly to about 1.7 volts at 3000 RPM, at full open 4.0-4.8 volts. See THROTTLE POSITION SENSOR OUTPUT SPECIFICATIONS  table. If voltages are as specified, go to next step. If voltages are not as specified, check TP sensor wiring and connector for damage, or loose connection. If problem exists, repair wiring or connector as necessary. If problem does not exist, temporarily install a know good TP sensor. If problem is corrected, replace TP sensor.
    THROTTLE POSITION SENSOR OUTPUT SPECIFICATIONS

    Engine Speed - RPM (1) TPS Output - Voltage
    Idle 0.3-0.9
    Accelerating Engine 3.0-4.0
    (1) Approximate values at sea level and 50 percent relative humidity. Throttle full open approimately 4.0-4.8 volts.
  7. Turn ignition off. Disconnect ECM and TP sensor harness connectors. Measure resistance of all three circuits. Blue, Black/White, and LightBlue/Black wire between TP sensor harness connector and ECM harness connector. Resistance should be less than one ohm. See IDENTIFYING THROTTLE POSITION SENSOR-TO-ECM CIRCUITS  table. See Figure or Figure and Figure . If each circuit resistance is less than one ohm, go to next step. If any resistance is one ohm or more, repair appropriate wire(s) between TP sensor and ECM.
  8. Connect TP sensor harness connector. Disconnect MAF sensor 5-pin connector. Measure resistance of all three circuits. Brown, Grey and Black/White wire between MAF sensor harness connector and ECM harness connector. See IDENTIFYING MASS AIRFLOW SENSOR-TO-ECM CIRCUITS  table. Resistance should be less than one ohm. See Figure, Figure and Figure . If any resistance is one ohm or more, repair appropriate wire(s) between MAF sensor and ECM. If each circuit resistance is less than one ohm, go to next step.
    IDENTIFYING THROTTLE POSITION SENSOR-TO-ECM CIRCUITS

    Throtle Position Sensor Connector /Terminal No. Wire Color ECM Connector Terminal No.
    A/T
    1 Blue C8
    2 LightBlue/Black B6
    3 Black/White B17
    M/T
    1 Blue D14
    2 LightBlue/Black D11
    3 Black/White D22
    IDENTIFYING MASS AIRFLOW SENSOR-TO-ECM CIRCUITS

    MAF Sensor Connector /Terminal No. Wire Color ECM Connector Terminal No.
    A/T
    1 Tan (1)
    2 Pink (3)
    3 Black/White B17
    4 Gray B6
    5 Brown B15
    M/T
    1 Tan (2)
    2 Pink (3)
    3 Black/White D22
    4 Gray D11
    5 Brown D15
    (1) Intake air temperature sensor (B24).
    (2) Intake air temperature sensor (D2).
    (3) EGR fuse (15-amp).
  9. Measure voltage between MAF sensor harness connector terminal No. 2 (Pink wire) and ground. Is battery voltage present, If voltage is not present, check for open circuit in Pink wire between MAF and EGR fuse (15-amp). Repair power circuit as necessary. Clear codes and retest.