LEMON Manuals: Even more car manuals for everyone

Torque Specifications

TORQUE SPECIFICATIONS

Application Ft. Lbs. (N.m)
Auto Tensioner Bolt 15-20 (20-27)
Block Plug Cap 15-20 (20-27)
Camshaft Bearing Cap Bolt 14-15 (19-20)
Camshaft Position Sensor Bolt 11-16 (15-22)
Camshaft Sprocket Bolt 59-74 (80-100)
Connecting Rod Cap Bolt
Step 1 13-16 (18-22)
Step 2 Additional 90 Degrees
Crankshaft Pulley Bolt 81-96 (110-130)
Cylinder Head Bolts (1)
New Bolts
Step 1 (2)
Step 2 (3)
Step 3 (4)
Original Bolts
Step 1 (2)
Step 2 (3)
Step 3 (3)
Engine Mounts
Bracket Bolt/Nut 43-58 (58-79)
Front Roll Stopper
Bracket-To-Sub-Frame Bolt 43-58 (58-79)
Bracket-To-Transaxle Bolt 43-58 (58-79)
Insulator Bolt/Nut 36-47 (49-64)
Insulator Bolt 66-81 (90-110)
Rear Roll Stopper
Bracket-To-Sub-Frame Bolt 37-48 (50-65)
Bracket-To-Transaxle Bolt 44-59 (60-80)
Insulator Bolt/Nut 37-48 (50-65)
Transaxle Mount
Bracket Bolt 44-59 (60-80)
Insulator Bolt 66-81 (90-110)
Sub-Bracket Bolt 44-59 (60-80)
Exhaust Manifold Mounting Bolt
M8 Bolt 18-22 (25-30)
M10 Bolt 26-41 (35-55)
Exhaust Pipe Clamp Bolt 14-22 (19-30)
Exhaust Pipe-To-Manifold Nut 22-29 (30-39)
Flywheel-To-Crankshaft Bolt 94-101 (127-137)
Front Case Bolt 14-20 (19-27)
Idler Pulley Bolt 33-40 (45-54)
Intake Manifold
Bracket Bolt 13-18 (15-24)
Mounting Bolt
M8 Bolt 11-15 (15-20)
M10 Bolt 13-18 (18-24)
Mounting Nut 22-30 (30-41)
Main Bearing Cap Bolt
Step 1 18 (24)
Step 2 Additional 90-94 Degrees
Oil Drain Plug 25-33 (34-45)
Oil Pump
Case Bolt 14-20 (19-27)
Cover Bolt 11-13 (15-18)
Driven Gear Bolt 25-29 (34-39)
Sprocket Nut 36-43 (49-58)
Oil Screen Bolt 11-16 (15-22)
Starter Bolt 20-25 (27-34)
Tensioner Pulley Bolt 31-40 (42-54)
Tensioner Pulley Bracket Bolt 17-20 (23-27)
Throttle Body-To-Intake Manifold Bolt 11-15 (15-20)
Timing Belt
Lower & Upper Cover Bolt (5)
Left Rear Cover Bolt
Lower 22-30 (30-41)
Upper (6)
Right Rear Cover Bolt (6)
Timing Belt Tensioner Bolt 32-40 (43-55)
Water Pump Mounting Bolt 11-15 (15-20)
INCH Lbs. (N.m) 
Camshaft Position Sensor Bolt 89-115 (10-13)
Oil Pan Bolt 89-106 (10-12)
Oil Pressure Switch 71- 106 (8-12)
Oil Seal Case Bolt 89-106 (10-12)
Rear Oil Seal Case Bolt 89-106 (10-12)
Rocker Cover Bolt 71-89 (8-10)
Thermostat Housing Bolt 89-133 (10-15)
Valve Cover Bolts 71-89 (8-10)
Water Pump Pulley Bolt 71-89 (8-10)
(1) Tighten in sequence with engine cold. See Figure.
(2) Tighten to 14 ft. lbs. (19 N.m)
(3) Tighten bolts in sequence an additional 90 degrees. See Figure.
(4) Loosen bolts in sequence, and repeat steps 2 and 3. Then tighten an additional 90 degrees.
(5) Tighten to 71-89 INCH lbs. (8-10 N.m).
(6) Tighten to 89-106 INCH lbs. (10-12 N.m)