LEMON Manuals: Even more car manuals for everyone

Test 16A - Bus (+) & Bus (-) Shorted Together

  1. Turn ignition off. Disconnect Powertrain Control Module (PCM). PCM is located at right corner of firewall. Turn ignition on. If scan tool does not display BUS (+) & BUS (-) SHORTED TOGETHER, replace PCM. If scan tool displays BUS (+) & BUS (-) SHORTED TOGETHER, go to next step.
  2. Turn ignition off. Disconnect Compass/Mini-Trip Computer (CMTC) module. Turn ignition on. If scan tool does not display BUS (+) & BUS (-) SHORTED TOGETHER, replace CMTC. If scan tool displays BUS (+) & BUS (-) SHORTED TOGETHER, go to next step.
  3. Turn ignition off. Disconnect Automatic Temperature Control (ATC) head connector. Turn ignition on. If scan tool does not display BUS (+) & BUS (-) SHORTED TOGETHER, replace ATC head. If scan tool displays BUS (+) & BUS (-) SHORTED TOGETHER, go to next step.
  4. Turn ignition off. Disconnect instrument cluster. Turn ignition on. If scan tool does not display BUS (+) & BUS (-) SHORTED TOGETHER, replace instrument cluster circuit board. If scan tool displays BUS (+) & BUS (-) SHORTED TOGETHER, go to next step.
  5. Turn ignition off. Disconnect Vehicle Information Center (VIC). Turn ignition on. If scan tool does not display BUS (+) & BUS (-) SHORTED TOGETHER, replace VIC. If scan tool displays BUS (+) & BUS (-) SHORTED TOGETHER, go to next step.
  6. Turn ignition off. Disconnect CCD radio. Turn ignition on. If scan tool does not display BUS (+) & BUS (-) SHORTED TOGETHER, replace radio. If scan tool displays BUS (+) & BUS (-) SHORTED TOGETHER, go to next step.
  7. Turn ignition off. Disconnect memory seat module. Turn ignition on. If scan tool does not display BUS (+) & BUS (-) SHORTED TOGETHER, replace memory seat module. If scan tool displays BUS (+) & BUS (-) SHORTED TOGETHER, go to next step.
  8. Turn ignition off. Disconnect driver door module. Turn ignition on. If scan tool does not display BUS (+) & BUS (-) SHORTED TOGETHER, replace driver door module. If scan tool displays BUS (+) & BUS (-) SHORTED TOGETHER, go to next step.
  9. Turn ignition off. Disconnect passenger seat module. Turn ignition on. If scan tool does not display BUS (+) & BUS (-) SHORTED TOGETHER, replace passenger door module. If scan tool displays BUS (+) & BUS (-) SHORTED TOGETHER, go to next step.
  10. Turn ignition off. Disconnect Body Control Module (BCM) connectors. Turn ignition on. If scan tool does not display BUS (+) & BUS (-) SHORTED TOGETHER, replace BCM. If scan tool displays BUS (+) & BUS (-) SHORTED TOGETHER, go to next step.
  11. Turn ignition off and wait 5 minutes. Disconnect Air Bag System Control Module (ABSCM). ABSCM is located under center console. Turn ignition on. If scan tool does not display BUS (+) & BUS (-) SHORTED TOGETHER, replace ABSCM. If scan tool displays BUS (+) & BUS (-) SHORTED TOGETHER, go to next step.
  12. Disconnect scan tool from DLC. Using external ohmmeter, measure resistance between terminals No. 3 (Violet/Brown wire) and No. 11 (White/Black wire) on DLC connector. If resistance is less than 5 ohms, repair short between Violet/Brown wire and White/Dark Green wire. If resistance is 5 ohms or greater, replace scan tool cable or scan tool as necessary.
NOTE: For connector terminal identification, refer to CONNECTOR IDENTIFICATION  . For wiring diagrams, refer to WIRING DIAGRAMS  . After each repair, perform TEST VER-1A  .
CAUTION: Always turn ignition off prior to disconnecting any module connector.