Test TC-40A - No Crank Reference Signal At Pcm
NOTE:
For connector terminal ID, see CONNECTOR IDENTIFICATION DIRECTORY. For component location see wiring diagram in the WIRING DIAGRAMS
article.
- Attempt to start engine while using scan tool to monitor CURRENT CKP COUNT. If scan tool does not display a change in CKP count when attempting to start engine, go to step 5). If scan tool displays a change in CKP count when attempting to start engine, go to next step.
- Condition required to set DTC is not present at this time. NO CRANK REFERENCE SIGNAL DTC sets when no Crankshaft Position (CKP) sensor signal is received by Powertrain Control Module (PCM) during engine cranking, Camshaft Position (CMP) sensor signal is present with no CKP sensor signal, or no CMP sensor signal is present when CKP sensor signal is present. Possible causes are: open or shorted sensor wiring, defective connections, improper CKP or CMP sensor clearance, defective CKP or CMP sensor and components, damaged flywheel or crankshaft pulse ring, broken timing belt or defective PCM. Go to next step.
- Inspect all related wiring and connectors. Repair wiring and connectors as necessary and perform TEST VER-2A. If wiring and connectors are okay, go to next step.
- Start engine and allow it to idle. Wiggle wiring harness from PCM to CMP sensor and CKP sensor. If engine misfires or stalls while wiggling wiring harness, repair wiring harness as necessary and perform TEST VER-2A. If engine does not misfire or stall while wiggling wiring harness, see INACTIVE DTC CONDITION. Test is complete. Perform TEST VER-2A.
- Turn ignition off. Disconnect Crankshaft Position (CKP) sensor connector. Inspect connector and terminals for damage. Repair connector and terminals as necessary and perform TEST VER-2A. If connector and terminals are okay, go to next step.
- Turn ignition on. Using an external voltmeter, check voltage on CKP sensor connector, 5-volt supply circuit (Orange wire). If voltage is 4.5 volts or less, go to step 11). If voltage is more than 4.5 volts, go to next step.
- Turn ignition off. Using an external ohmmeter, check resistance between ground and CKP sensor connector, ground circuit (Brown/Yellow wire). If resistance is 5 ohms or more, repair open ground circuit and perform TEST VER-2A. If resistance is less than 5 ohms, go to next step.
- Disconnect Powertrain Control Module (PCM) Black connector. Inspect connector and terminals for damage. Repair connector and terminals as necessary and perform TEST VER-2A. If connector and terminals are okay, go to next step.
- Using an external ohmmeter, check resistance of signal circuit (Gray/Black wire) between CKP sensor connector and PCM Black connector. If resistance is 5 ohms or more, repair open signal circuit and perform TEST VER-2A. If resistance is less than 5 ohms, go to next step.
- Check resistance between ground and PCM Black connector, CKP signal circuit (Gray/Black wire). If resistance is 5 ohms or more, replace CKP sensor and perform TEST VER-2A. If resistance is less than 5 ohms, repair short to ground in signal circuit and perform TEST VER-2A.
- Turn ignition off. Disconnect Powertrain Control Module (PCM) Black connector. Inspect connector and terminals for damage. Repair connector and terminals as necessary and perform TEST VER-2A. If connector and terminals are okay, go to next step.
- Using an external ohmmeter, check resistance of 5-volt supply circuit (Orange wire) between CKP sensor connector and PCM Black connector. If resistance is 5 ohms or more, repair open 5-volt supply circuit and perform TEST VER-2A. If resistance is less than 5 ohms, go to next step.
- Check resistance between ground and PCM Black connector, CKP 5-volt supply circuit (Orange wire). If resistance is less than 5 ohms, repair short to ground in 5-volt supply circuit and perform TEST VER-2A. If resistance is 5 ohms or more, replace PCM and perform TEST VER-2A.