LEMON Manuals: Even more car manuals for everyone

Test TC-171A - Governor Pressure Solenoid/Trans Relay CKTS

NOTE: For connector terminal ID, see CONNECTOR IDENTIFICATION DIRECTORY. For component location see wiring diagram in the WIRING DIAGRAMS article.
  1. Using scan tool, read DTCs. If 12-VOLT RELAY CONTROL CIRCUIT DTC is also set, perform TEST TC-173A. If 12-VOLT RELAY CONTROL CIRCUIT DTC is not set, go to next step.
  2. Using scan tool, perform GOV and 3-4 shift test. Select 1st gear and read governor pressure voltage. If voltage is one volt or more, go to step 6). If voltage is less than one volt, go to next step.
  3. Condition required to set DTC is not present at this time. GOVERNOR PRESSURE SOLENOID CIRCUIT DTC sets if current state of solenoid output is different from expected output for 4.48 seconds. Possible causes are: defective transmission control relay, incorrectly wired connector, open or shorted wiring, dirty or corroded connector, defective connector terminals, or defective PCM. Go to next step.
  4. Inspect all related wiring and connectors. Repair wiring and connectors as necessary and perform TEST VER-2A. If wiring and connectors are okay, go to next step.
  5. Using scan tool, erase DTCs. Start engine. Using scan tool, read DTCs while wiggling wiring harness from governor pressure solenoid to PCM and note if GOVERNOR PRESSURE SOLENOID CIRCUIT DTC resets. If DTC resets, repair wiring harness as necessary and perform TEST VER-2A. If DTC does not reset, see INACTIVE DTC CONDITION. Test is complete. Perform TEST VER-2A.
  6. Turn ignition off. Disconnect transmission solenoid connector. Inspect connector and terminals for damage. Repair connector and terminals as necessary and perform TEST VER-2A. If connector and terminals are okay, go to next step.
  7. Turn ignition on. Using scan tool, actuate transmission control relay. Using scan tool in voltmeter mode, check voltage on transmission solenoid connector, transmission relay output circuit (Light Blue wire). If voltage does not switch from zero to more than 10 volts, perform TEST TC-171B. If voltage switches from zero to more than 10 volts, go to next step.
  8. Turn ignition off. Disconnect Powertrain Control Module (PCM) connectors. Inspect connectors and terminals for damage. Repair connectors and terminals as necessary and perform TEST VER-2A. If connectors and terminals are okay, go to next step.
  9. Turn ignition on. Check voltage on transmission solenoid connector, governor pressure solenoid control circuit (Pink wire). If voltage is more than 10 volts, perform TEST TC-171D. If voltage is 10 volts or less, go to next step.
  10. Reconnect transmission solenoid connector. Turn ignition off. Using an external ohmmeter, check resistance between ground and PCM White connector, governor pressure solenoid control circuit (Pink wire). If resistance is 5 ohms or less, repair short to ground in governor pressure solenoid control circuit and perform TEST VER-2A. If resistance is more than 5 ohms, go to next step.
  11. Remove transmission control relay. Inspect transmission control relay connector and terminals for damage. Repair connector and terminals as necessary and perform TEST VER-2A. If connector and terminals are okay, go to next step.
  12. Using external ohmmeter, connect one lead to transmission control relay connector, transmission control relay output circuit (Light Blue wire). Go to next step.
  13. Connect other lead to PCM White connector, governor pressure solenoid control circuit (Pink wire). If resistance is 2.5-5.0 ohms, replace PCM and perform TEST VER-2A. If resistance is 5 ohms or less, perform TEST TC-171C. If resistance is more than 5 ohms, go to next step.
  14. Disconnect transmission solenoid connector. Inspect connector and terminals for damage. Repair connector and terminals as necessary and perform TEST VER-2A. If connector and terminals are okay, go to next step.
  15. Check resistance of governor pressure solenoid control circuit (Pink wire) between PCM White connector and transmission solenoid connector. If resistance is more than 5 ohms, repair open governor pressure solenoid control and perform TEST VER-2A. If resistance is 5 ohms or less, go to next step.
  16. Drain and remove transmission pan. Disconnect governor pressure solenoid connector. Inspect connector and terminals for damage. Repair connector and terminals as necessary and perform TEST VER-2A. If connector and terminals are okay, go to next step.
  17. Check resistance across governor pressure solenoid terminals. If resistance is 5 ohms or less, replace transmission solenoid and harness assembly. Perform TEST VER-2A. If resistance is more than 5 ohms, replace governor pressure solenoid and perform TEST VER-2A.