Test TC-106A - Multiple Cylinder Misfire
NOTE:
For connector terminal ID, see CONNECTOR IDENTIFICATION DIRECTORY. For component location see wiring diagram in the WIRING DIAGRAMS
article.
NOTE:
MULTIPLE CYLINDER MISFIRE DTC sets only if condition occurs during driving cycle.
- Repair any other DTCs before proceeding. Using scan tool, clear DTCs. Start engine. Allow engine to reach operating temperature. Road test vehicle. Stop vehicle, turn engine off, then on. Go to next step.
- Start engine. Continue road test. Drive vehicle at various vehicle and engine speeds. Avoid sharp maneuvers. Return to service bay. Stop vehicle. Turn ignition off and go to next step.
- Turn ignition on. Using scan tool, read DTCs. If MULTIPLE CYLINDER MISFIRE DTC returns, go to step 7). If MULTIPLE CYLINDER MISFIRE DTC does not return, and CYLINDER #1, #2, #3, #4, #5, #6, #7, #8, #9 or #10 MISFIRE DTC returns, perform TEST TC-107A. If no CYLINDER MISFIRE DTCs returns, go to next step.NOTE: Refer to manufacturer's operation manual for instructions in use of engine analyzer and procedure for pattern analysis.
- Connect an engine analyzer to engine. Start engine and check secondary ignition pattern. Repair indicated secondary ignition system component as necessary and perform TEST VER-5A. If secondary ignition pattern is okay, go to next step.NOTE: DO NOT spray inductive pick-up.
- Using a spray bottle, spray ignition cables with water while observing secondary ignition pattern. If pattern changes while spraying water, repair appropriate ignition cable(s) and perform TEST VER-5A. If pattern is okay, go to next step.
- Condition required to set DTC is not present at this time. MULTIPLE CYLINDER MISFIRE DTC sets when Powertrain Control Module (PCM) senses an absence of spark. Possible causes are: inaccurate vehicle speed sensor reading (too high), defective ignition coil circuit, defective spark plug, defective spark plug cable or connector, defective fuel pump or filter, mechanical engine problem, defective EGR system, defective fuel injectors or connectors, restricted exhaust, low fuel level, restricted intake system, defective PCM power grounds, defective EVAP system or defective PCM. See INACTIVE DTC CONDITION. Test is complete. Perform TEST VER-5A.NOTE: Refer to manufacturer's operation manual for instructions in use of engine analyzer and procedure for pattern analysis.
- Inspect ignition cables for proper installation. Repair cable installation as necessary and perform TEST VER-5A. If cables are installed properly, go to next step.
- Turn ignition off. Connect an engine analyzer to engine. Start engine and allow it to idle. If engine will not idle, maintain constant engine speed at more than idle. Go to next step.
- Set engine analyzer to read display or parade pattern and check secondary ignition pattern while momentarily removing and reinstalling each spark plug wire from ignition coil or distributor. If secondary voltage is not at least 25,000 volts for each wire, replace ignition coil and perform TEST VER-5A. If voltage is as specified, go to next step.
- Turn ignition off. Remove all spark plugs. Remove Auto Shutdown (ASD) relay. Check engine compression. If cylinder(s) that set DTC is not at least 100 psi and within 25 percent of other cylinders, repair engine mechanical problem as necessary and perform TEST VER-5A. If cylinder(s) test as specified, reinstall spark plugs and go to next step.
- Turn ignition off. Connect a vacuum gauge to engine vacuum source. Start engine and allow it to reach normal operating temperature. With parking brake on and shift lever in Neutral, read vacuum gauge. If vacuum gauge does not read at least 13 in. Hg, perform TEST NTC-22A. If vacuum gauge reads at least 13 in. Hg, go to next step.
- While observing vacuum gauge, snap throttle open and closed. If vacuum does not drop rapidly to zero, repair restricted exhaust system and perform TEST VER-5A. If vacuum drops rapidly to zero, turn ignition off and go to next step.WARNING: Fuel system may be under extreme pressure. Release fuel pressure before connecting fuel pressure gauge. See FUEL PRESSURE RELEASE.
- Release fuel pressure. Connect a fuel pressure gauge to fuel rail. Turn ignition on. Go to next step.
- Using scan tool, actuate fuel system test. Allow time for fuel pressure gauge to stabilize to normal fuel pressure. Go to next step.
- Using scan tool, stop fuel system test. Observe fuel pressure gauge for one minute. If fuel pressure drops to less than 10 psi, perform TEST NTC-3A. If fuel pressure does not drop to less than 10 psi, go to next step.
- Inspect air cleaner and air inlet ducts for restrictions. Clean and repair restrictions as necessary and perform TEST VER-5A. If no restrictions exist, go to next step.
- Inspect injector wiring and connections. Repair wiring and connectors as necessary and perform TEST VER-5A. If wiring and connectors are okay, go to next step.
- Perform each test in order listed in REPAIRING MULTIPLE CYLINDER MISFIRE TESTS table. If a test passes, continue to next test until problem is located.
REPAIRING MULTIPLE CYLINDER MISFIRE TESTS
| Description | Perform Test No. |
|---|---|
| Secondary Ignition Patterns | NTC-2A |
| Fuel Pressure | NTC-3A |
| PCM Ground & Power Circuits | NTC-11A |
| Engine Mechanical Systems | NTC-22A |