Diagnostic Procedure
NOTE:
For better performance and results of this diagnostic procedure, usage of appropriate wiring diagram is recommended. See ENGINE PERFORMANCE
in SYSTEM WIRING DIAGRAMS article in ELECTRICAL.
NOTE:
Perform all voltage and resistance tests using a Digital Volt-Ohmmeter (DVOM) with a minimum 10-megohm input impedance, unless stated otherwise in test procedure. Use an ohmmeter to isolate wiring harness shorts or opens.
- Perform ON-BOARD DIAGNOSTIC II SYSTEM CHECK under SELF-DIAGNOSTIC SYSTEM. After performing OBD-II system check, go to next step.
- Turn ignition on. Review and record FAILURE RECORDS data on scan tool. Operate vehicle within FAILURE RECORDS conditions. On scan tool, monitor DTC information. If DTC P0106 is not set, go to next step. If DTC P0106 is set, go to step 4 .
- Check for the following conditions:
- Vacuum hoses disconnected, damaged or misrouted.
- Intake manifold leaks.
- Vacuum leaks at throttle body or EGR valve and/or piping.
- Positive Crankcase Ventilation (PCV) valve improperly installed, damaged or missing.
If problem is found, repair as necessary. After repair is complete, see VERIFYING VEHICLE REPAIR under SELF-DIAGNOSTIC SYSTEM. If no problems are found, check for an intermittent problem. See DIAGNOSTIC AIDS .
- Turn ignition off. Disconnect MAP sensor 3-pin harness connector. MAP sensor is located at top rear of intake manifold. See Figure . Turn ignition on. On scan tool, observe MAP sensor parameter. MAP sensor parameter should be about 11 kPa. If display is as specified, go to next step. If display is not as specified, go to step 13 .
- Connect a test light between battery voltage and MAP sensor harness connector terminal No. 2 (Red wire). See Fig 1 . On scan tool, observe MAP sensor parameter. MAP sensor parameter should be about 105 kPa. If display is as specified, go to next step. If display is not as specified, go to step 9 .
- Using a fused jumper wire, connect MAP sensor harness connector terminals No. 2 (Red wire) and No. 3 (Black wire). See Fig 1 . On scan tool, observe MAP sensor parameter. MAP sensor parameter should be about 104 kPa. If display is as specified, go to next step. If display is not as specified, go to step 8 .
- Turn ignition off. Disconnect ECM 80-pin harness connectors E-22. ECM is located at left rear of engine compartment, near air filter housing. See Figure . Check for high resistance, open or poor connection in Green wire between ECM and MAP sensor. Check for poor or loose terminals in ECM harness connectors. See Figure . If problem with wiring is found, repair as necessary. After repair is complete, see VERIFYING VEHICLE REPAIR under SELF-DIAGNOSTIC SYSTEM. If no problem is found, go to step 11 .
- Check for high resistance, open or poor connection in Black wire between ECM and MAP sensor. If problem with wiring is found, repair as necessary. After repair is complete, see VERIFYING VEHICLE REPAIR under SELF-DIAGNOSTIC SYSTEM. If no problem is found, check for poor, loose or corroded connection at ECM harness connector E-22 terminal No. 29 (Red wire). See Figure . If problem with terminal is found, repair or replace terminal as necessary. After repair is complete, see VERIFYING VEHICLE REPAIR under SELF-DIAGNOSTIC SYSTEM. If no problem is found, go to step 10 .
- Turn ignition off. Disconnect ECM 80-pin harness connectors E-22. ECM is located at left rear of engine compartment, near air filter housing. See Figure . Check for high resistance, open, short to ground or short to sensor ground in Red wire between ECM and MAP sensor. If no problem is found, go to next step. If problem with wiring is found, repair as necessary. After repair is complete, see VERIFYING VEHICLE REPAIR under SELF-DIAGNOSTIC SYSTEM.
- Check for poor, loose or corroded connection at ECM harness connector E-22 terminal No. 29 (Red wire). See Figure . If problem with terminal is found, repair or replace terminal as necessary. After repair is complete, see VERIFYING VEHICLE REPAIR under SELF-DIAGNOSTIC SYSTEM. If no problem is found, go to step 14 .
- Check for poor, loose or corroded terminals in MAP sensor harness connector. If no problem is found, go to next step. If problem with terminal(s) are found, repair or replace terminal(s) as necessary. After repair is complete, see VERIFYING VEHICLE REPAIR under SELF-DIAGNOSTIC SYSTEM.
- Replace MAP sensor. See MANIFOLD ABSOLUTE PRESSURE SENSOR under SENSORS & SWITCHES in article. After repair is complete, see VERIFYING VEHICLE REPAIR under SELF-DIAGNOSTIC SYSTEM.
- Turn ignition off. Disconnect ECM 80-pin harness connectors E-22. ECM is located at left rear of engine compartment, near air filter housing. See Figure . Turn ignition on. Check for short to voltage or short to 5 volt reference circuit in Red wire between ECM and MAP sensor. If no problem is found, go to next step. If problem with wiring is found, repair as necessary. After repair is complete, see VERIFYING VEHICLE REPAIR under SELF-DIAGNOSTIC SYSTEM.
- Replace and reprogram ECM. See POWERTRAIN CONTROL MODULE REPLACEMENT under POWERTRAIN CONTROL MODULE. Use scan tool to clear DTC and verify repair.