LEMON Manuals: Even more car manuals for everyone

Voluntary Safety Recall Campaign 2012 - 2013 M35 Hybrid Control Module (ITB16-029)

Publication date: 2016-08-09
Reference number: ITB16-029

VOLUNTARY SAFETY RECALL CAMPAIGN 2012 - 2013 M35 HYBRID CONTROL MODULE

VOLUNTARY SAFETY RECALL CAMPAIGN 2012 - 2013 M35 HYBRID CONTROL MODULE

SERVICE CAMPAIGN BULLETIN

Reference Number(s): ITB16-029, Date of Issue:  August 9, 2016
INFINITI: 2012 - 2013 M35 Hybrid
CAMPAIGN I.D.#/NHTSA #: R1623/16V-527
APPLIED VEHICLES: 2012 - 2013 M35 Hybrid (Y51)
NOTE: Check Service COMM to confirm campaign eligibility.

INTRODUCTION

Infiniti is conducting a voluntary safety recall campaign on certain specific Model Year 2012 - 2013 M35 Hybrid vehicles to reprogram the Hybrid Powertrain Control Module, Traction Motor Controller, and the Transmission Control Module. This service will be provided at no charge to the customer for parts or labor.

IDENTIFICATION NUMBER

Infiniti has assigned identification number R1623 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign.

DEALER RESPONSIBILITY

It is the dealer's responsibility to check Service COMM for the campaign status on each vehicle falling within the range of this voluntary safety recall which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a dealer's inventory. Federal law requires that new vehicles in dealer inventory which are the subject of a safety recall must be corrected prior to sale. Failure to do so can result in civil penalties by the National Highway Traffic Safety Administration.  While federal law applies only to new vehicles, Infiniti strongly encourages dealers to correct any used vehicles in their inventory before they are retailed.

REPAIR OVERVIEW

G10766837
MODULES AND ORDER OF REPROGRAMMING

Order of reprogramming Control Module Listed in C-III plus as:
1 Hybrid Powertrain Control Module EV/HEV
2 Traction Motor Controller MOTOR CONTROLLER
3 Transmission Control Module TRANSMISSION

SERVICE PROCEDURE

IMPORTANT: The reprogramming procedure in this bulletin must be performed 3 separate times to reprogram the control modules for EV/HEV, MOTOR CONTROLLER, and TRANSMISSION.
  1. Before continuing, it is IMPORTANT to make sure: 
    • ASIST on the CONSULT PC has been freshly synchronized (updated) to the current date. 
    • All CONSULT related software updates (if any) have been installed. 
    NOTE: The CONSULT PC automatically gets all reprogramming software during ASIST synchronization.
    CAUTION:
    • Connect the GR8 to the vehicle 12 volt battery and set to ECM power supply mode. If the vehicle battery voltage drops below 12.0V or rises above 15.5V  during reprogramming, control unit may be damaged  .
    • Be sure to turn OFF all vehicle electrical loads. If a vehicle electrical load remains ON, control unit may be damaged  .
    • Be sure to connect the AC Adapter. If the CONSULT PC battery voltage drops during reprogramming, the process will be interrupted and control unit may be damaged  .
    • Turn OFF all external Bluetooth® devices (e.g., cell phones, printers, etc.) within range of the CONSULT PC and the plus VI. If Bluetooth® signal waves are within range of the CONSULT PC during reprogramming, reprogramming may be interrupted and control unit may be damaged  .
  2. Once all ASIST and CONSULT related updates have been performed, attach the CONSULT PC to the vehicle.
    • Connect the plus VI to the vehicle.
    • Connect the AC adapter to the CONSULT PC.
  3. Turn ON the CONSULT PC, and then open CONSULT III plus (C-III plus).
    NOTE: Make sure all applications other than C-III plus are closed.
  4. Press the ignition switch twice without  depressing the brake pedal.
    • The meter and gauges will illuminate.
    • Make sure the Ready light is OFF.
  5. Check for stored DTCs in all systems as follows:
    1. Wait for the plus VI to be recognized.
    2. Select Diagnosis (All Systems)  .
    3. Wait for System Call  to complete.
    4. Check for stored DTCs.
      • If no DTCs found, go to step 6.
      • If any DTCs are found stored:
        • Perform diagnosis and repairs related to the stored DTC(s), and then erase the DTC(s).
        • When completed, go to step 6.
        IMPORTANT: The reprogramming procedure in this bulletin must be performed 3 separate times to reprogram the control modules for EV/HEV, MOTOR CONTROLLER, and TRANSMISSION.
  6. Go to Re/programming  , Configuration.
    1. Select the Home  button, and then YES  to return to the screen shown in Figure 1.
    2. Select Re/programming, Configuration  .
      G10766838
  7. Check the box for Confirmed Instructions, and then select Next  .
    G10766839
  8. If the screen in Figure 3 does not display, skip to step  10.
  9. If the screen in Figure 3 displays, select Automatic Selection (VIN).
    G10766840
  10. Verify the VIN or Chassis #  matches that of the vehicle.
    • If the correct VIN is displayed, select Confirm  .
      G10766841
  11. Select Confirm  again.
    G10766842
  12. Use the page arrows to scroll and select the correct control module  to be reprogrammed.
    IMPORTANT: The reprogramming procedure in this bulletin must be performed 3 separate times to reprogram the control modules in this order: EV/HEV, MOTOR CONTROL, and TRANSMISSION.
    NOTE: EV/HEV and TRANSMISSION are shown in Figure 6; MOTOR CONTROLLER is not shown.
    G10766843
  13. Wait for System Call to complete, and then select Reprogramming  .
    G10766844
  14. When you get to the screen shown in Figure 8, confirm reprogramming applies as follows:
    1. Find the current Part Number  and write it on the repair order.
      G10766845
    2. Compare the P/N written down to the P/Ns in the Current Part Number  column of TABLE A  below:
      • If there is a match  , reprogramming applies  . Continue with the reprogramming procedure.
      • If there is not a match  , this campaign does not apply  or it has already been done.
        NOTE: Make sure to check for a match for all 3 control modules.
    3. If there is a P/N match as specified above, select Save  , and then continue with the reprogramming procedure.
      CURRENT PART NUMBER

      MODEL CONTROL MODULE CURRENT PART NUMBER (P/N):
      2012 - 2013 M35 Hybrid EV/HEV 237A0 - 1MG0A, 1MG0B, 1MG0C, 1MG0D
      237A0 - 1MG4A, 1MG4B, 1MG4C, 1MG4D
      237A0 - 1MG8A, 1MG8B
      237A0 - 1PM0A, 1PM0B, 1PM0C, 1PM0D
      237A0 - 1PM4A, 1PM4B
      237A0 - 1PN0A, 1PN0B
      MOTOR CONTROLLER 291A0 - 1MG0B, 1MG1B
      TRANSMISSION 31039 - 3SX0A, 3SX1A, 3SX2A, 3SX3A, 3SX4A, 3SX5A, 3SX9A
      31039 - X960A, X961A, X963A, X964A, X966A
      31039 - X967D
      31039 - 12X0A
      31039 - 12X3D
  15. Read the precautions on the C-III plus screen (use page arrow as needed). After reading, select Confirmed instructions  , and then select Next  .
    G10766846
    NOTE: In some cases, more than one new P/N for reprogramming is available.
    • If more than one new P/N is available, the screen in Figure 10 will display.
    • Select and use the reprogramming option that does not  have the message "Caution! Use ONLY with ITBXX-XXX".
    • If you get this screen and it is blank  (no reprogramming listed), it means there is no reprogramming available for that control unit.
      G10766847
  16. Verify the Current Part Number  matches the P/N written down in step  14, and then select Next  .
    G10766848
  17. Confirm battery voltage is correct, and then select Next  .
    NOTE: Battery voltage must stay within the specified range to make the indicator turn green.
    G10766849
  18. Confirm all items on the C-III plus screen are OK (green), then select Start  .
    • The reprogramming process begins when Start  is selected.
      NOTE: For reprogramming to continue, vehicle 12V battery voltage must stay within 12 volts and 15.5 volts.
      G10766850
  19. Wait for both bar graphs to complete.
    G10766851
  20. When the screen in Figure 15 displays, reprogramming is complete.
    NOTE: If the screen in Figure 15 does not  display (indicating that reprogramming did not  complete), refer to the information on SERVICE PROCEDURE .
  21. Select Next  .
    G10766852
    NOTE:
    • In the next step 22, you will perform DTC erase
    • DTC erase is required before C-III plus will provide the final reprogramming confirmation report.

    Control Unit Recovery: 

    Do not disconnect plus VI or shut down C-III plus if reprogramming does not complete. 

    If reprogramming does not complete and the "!?" icon displays as shown in Figure 16: 

    • Check battery voltage (12.0-15.5 V).
    • Ignition is ON, not Ready.
    • External Bluetooth® devices are OFF.
    • All electrical loads are OFF.
    • Select retry and follow the on screen instructions. 
    • "Retry" may not go through on first attempt and can be selected more than once. 
      G10766853

    If reprogramming does not  complete and the "X" icon displays as shown in Figure 17:

    • Check battery voltage (12.0 - 15.5 V).
    • CONSULT A/C adapter is plugged in.
    • Ignition is ON, not Ready.
    • Transmission is in Park.
    • All C-III plus/VI cables are securely connected.
    • All C-III plus updates are installed.
    • Select Home, and restart the reprogram procedure from the beginning. 
      G10766854
  22. Erase all DTCs as follows:
    1. Turn the ignition OFF.
      • The screen in Figure 18 will read OFF after pressing the power switch once.
        G10766855
    2. Turn the ignition ON, not Ready (press switch twice, no foot on brake).
      • The screen in Figure 19 will read ON  after pressing the power switch twice  .
        G10766856
    3. Wait for the bar graph in the ERASE  window to complete 100%.
    4. Select Next  .
      G10766857
  23. Verify the P/N has changed (before and after reprogramming P/Ns should be different).
    1. Print a copy of the screen in Figure 21 by selecting Print.
    2. Attach the copy to the repair order.
    3. Once a copy has been printed, select Confirm.
      G10766858
  24. After confirmation has completed, select Home
    G10766859
  25. Repeat the entire reprogramming procedure for MOTOR CONTROLLER.
  26. Repeat the entire reprogramming procedure for TRANSMISSION.
  27. Use C-III plus to check and erase  any stored DTCs in all systems as follows:
    1. Select Diagnosis (All Systems)  .
    2. Wait for System Call  to complete.
    3. Check and erase  any stored DTCs.
  28. Disconnect C-III plus from the vehicle.
  29. Turn the ignition OFF.
  30. Disconnect the GR8 from the 12V battery.

CLAIMS INFORMATION

Submit a "CM" line claim using the following claims coding:

CLAIMS INFORMATION

CAMPAIGN ("CM") I.D. DESCRIPTION OP CODE FRT
R1623 Reprogram EV/HEV, MOTOR CONTROLLER, and TRANSMISSION R16230 1.0 hrs.