LEMON Manuals: Even more car manuals for everyone

Door Mirror Sensor RH Circuit Check

  1. CHECK DOOR MIRROR FUNCTION 

    Check the following items.

    Operation malfunction in memory operation.

    NOTE: If a door mirror face position is set to an implausible angle, the set position may not be reproduced.

    OK or NG 

    OK: GO TO 2.

    NG: Repair or replace the malfunctioning parts, and check the symptom again.

  2. CHECK DOOR MIRROR RH SENSOR 

    With CONSULT-II 

    Check that "VOLTAGE" is displayed on "MIR/SE RH R-L, MIR/SE RH U-D" in the DATA MONITOR.

    MONITOR ITEM CONTENTS

    Monitor item [OPERATION or UNIT] Contents
    MIR/SEN RH R-L "V" Voltage output from door mirror RH sensor (LH/RH) is displayed.
    MIR/SEN RH U-D "V" Voltage output from door mirror RH sensor (UP/DOWN) is displayed.
    Fig 1: CONSULT II DATA MONITOR Screen
    G04145981Courtesy of NISSAN MOTOR CO., U.S.A.

    Without CONSULT-II 

    1. Turn ignition switch to ACC.
    2. Check voltage between automatic drive positioner control unit connector and ground.
    AUTOMATIC DRIVE POSITIONER CONTROL UNIT CONNECTOR AND GROUND VOLTAGE

    Automatic drive positioner control unit Terminals Condition Voltage (V) (Approx.)
    (+) (-)
    M6 21 Ground Mirror motor is operated UP or DOWN Changes between 3.5 (close to left edge) - 0.5 (close to right edge)
    5 Mirror motor is operated UP or DOWN Changes between 4.2 (close to peak) - 0.5 (close to valley)
    Fig 2: Identifying Voltage Between Automatic Drive Positioner Control Unit Connector And Ground
    G04145982Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: Mirror sensor RH circuit is OK.

    NG: GO TO 3.

  3. CHECK HARNESS CONTINUITY 1 
    1. Turn ignition switch OFF.
    2. Disconnect automatic drive positioner control unit connector and door mirror RH connector.
    3. Check continuity between automatic drive positioner control unit connector and door mirror RH connector.
      AUTOMATIC DRIVE POSITIONER CONTROL UNIT CONNECTOR AND DOOR MIRROR RH CONNECTOR CONTINUITY

      A B Continuity
      Automatic drive positioner control unit connector Terminal Door mirror RH connector Terminal
      M7 33 D39 11 Yes
      41 12
    4. Check continuity between automatic drive positioner control unit connector and ground.
      AUTOMATIC DRIVE POSITIONER CONTROL UNIT CONNECTOR AND GROUND CONTINUITY

      A Ground Continuity
      Automatic drive positioner control unit connector Terminal (Wire Color)
      M7 33 No
      41
      Fig 3: Identifying Continuity Between Automatic Drive Positioner Control Unit Connector And Door Mirror RH Connector
      G04145983Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: GO TO 4.

    NG: Repair or replace harness.

  4. CHECK HARNESS CONTINUITY 2 
    1. Check continuity between automatic drive positioner control unit connector and door mirror RH connector.
      AUTOMATIC DRIVE POSITIONER CONTROL UNIT CONNECTOR AND DOOR MIRROR RH CONNECTOR CONTINUITY

      A B Continuity
      Automatic drive positioner control unit connector Terminal Door mirror RH connector Terminal
      M6 5 D39 9 Yes
      21 10
    2. Check continuity between automatic drive positioner control unit connector and ground.
    AUTOMATIC DRIVE POSITIONER CONTROL UNIT CONNECTOR AND GROUND CONTINUITY

    A Ground Continuity
    Automatic drive positioner control unit connector Terminal
    M6 5 No
    21
    Fig 4: Identifying Continuity Between Automatic Drive Positioner Control Unit Connector And Door Mirror RH Connector
    G04145984Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: Replace door mirror RH.

    NG: Repair or replace harness.