LEMON Manuals: Even more car manuals for everyone

Door Mirror Sensor LH Circuit Check

  1. CHECK DOOR MIRROR FUNCTION 

    Check the following items.

    Operation malfunction in memory operation.

    NOTE: If a door mirror face position is set to an implausible angle, the set position may not be reproduced.

    OK or NG 

    OK: GO TO 2.

    NG: Repair or replace the malfunctioning parts, and check the symptom again.

  2. CHECK DOOR MIRROR LH SENSOR 

    With CONSULT-II 

    Check that "VOLTAGE" is displayed on "MIR/SE LH R-L, MIR/SE LH U-D" in the DATA MONITOR.

    MONITOR ITEM CONTENTS

    Monitor item [OPERATION or UNIT] Contents
    MIR/SEN LH R-L "V" Voltage output from door mirror LH sensor (LH/RH) is displayed.
    MIR/SEN LH U-D "V" Voltage output from door mirror LH sensor (UP/DOWN) is displayed.
    Fig 1: CONSULT II DATA MONITOR Screen
    G04145977Courtesy of NISSAN MOTOR CO., U.S.A.

    Without CONSULT-II 

    1. Turn ignition switch to ACC.
    2. Check voltage between automatic drive positioner control unit connector and ground.
    AUTOMATIC DRIVE POSITIONER CONTROL UNIT CONNECTOR AND GROUND VOLTAGE

    Automatic drive positioner control unit connector Terminals Condition Voltage (V) (Approx.)
    (+) (-)
    M6 22 Ground Mirror motor is operated LEFT or RIGHT Changes between 3.5 (close to right edge) - 0.5 (close to left edge)
    6 Mirror motor is operated UP or DOWN Changes between 4.2 (close to peak) - 0.5 (close to valley)
    Fig 2: Identifying Voltage Between Automatic Drive Positioner Control Unit Connector And Ground
    G04145978Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: Mirror sensor LH circuit is OK.

    NG: GO TO 3.

  3. CHECK HARNESS CONTINUITY 1 
    1. Turn ignition switch OFF.
    2. Disconnect automatic drive positioner control unit connector and door mirror LH connector.
    3. Check continuity between automatic drive positioner control unit connector and door mirror LH connector.
      AUTOMATIC DRIVE POSITIONER CONTROL UNIT CONNECTOR AND DOOR MIRROR LH CONNECTOR CONTINUITY

      A B Continuity
      Automatic drive positioner control unit connector Terminal Door mirror LH connector Terminal
      M7 33 D2 11 Yes
      41 12
    4. Check continuity between automatic drive positioner control unit connector and ground.
      AUTOMATIC DRIVE POSITIONER CONTROL UNIT CONNECTOR AND GROUND CONTINUITY

      A Ground Continuity
      Automatic drive positioner control unit connector Terminal
      M7 33 No
      41
      Fig 3: Identifying Continuity Between Automatic Drive Positioner Control Unit Connector And Door Mirror LH Connector
      G04145979Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: GO TO 4.

    NG: Repair or replace harness.

  4. CHECK HARNESS CONTINUITY 2 
    1. Check continuity between automatic drive positioner control unit connector and door mirror LH connector.
      AUTOMATIC DRIVE POSITIONER CONTROL UNIT CONNECTOR AND DOOR MIRROR LH CONNECTOR CONTINUITY

      A B Continuity
      Automatic drive positioner control unit connector Terminal Door mirror LH connector Terminal
      M6 6 D2 9 Yes
      22 10
    2. Check continuity between automatic drive positioner control unit connector and ground.
      AUTOMATIC DRIVE POSITIONER CONTROL UNIT CONNECTOR AND GROUND CONTINUITY

      A Ground Continuity
      Automatic drive positioner control unit connector Terminal
      M6 6 No
      22
      Fig 4: Identifying Continuity Between Automatic Drive Positioner Control Unit Connector And Door Mirror LH Connector
      G04145980Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: Replace door mirror LH.

    NG: Repair or replace harness.