LEMON Manuals: Even more car manuals for everyone

Control Valve And Tcm Removal And Installation: Installation

CAUTION: After completing installation, check fluid leakage and fluid level. Refer to CHANGING A/T FLUID  and CHECKING A/T FLUID .
  1. Install O-ring in A/T assembly harness connector.
    CAUTION:
    • Do not reuse O-ring.
    • Apply ATF to O-ring.
  2. Fig 1: Installing O-Ring In A/T Assembly Harness Connector
    G02250189Courtesy of NISSAN MOTOR CO., U.S.A.
  3. Install A/T fluid temperature sensor 2 to bracket.
  4. Fig 2: Installing A/T Fluid Temperature Sensor 2 To Bracket
    G02250190Courtesy of NISSAN MOTOR CO., U.S.A.
  5. Install A/T fluid temperature sensor 2 (with bracket) in control valve with TCM. Tighten A/T fluid temperature sensor 2 mounting bolt to the specified torque. Refer to COMPONENTS .
    CAUTION: Adjust bolt hole of bracket to bolt hole of control valve with TCM.
  6. Fig 3: Installing A/T Fluid Temperature Sensor 2 (With Bracket) In Control Valve With TCM
    G02250191Courtesy of NISSAN MOTOR CO., U.S.A.
  7. Install control valve with TCM in transmission case.
    CAUTION:
    • Make sure that turbine revolution sensor securely installs turbine revolution sensor hole.
    • Hang down revolution sensor harness toward outside so as not to disturb installation of control valve with TCM.
    • Adjust A/T assembly harness connector of control valve with TCM to terminal hole of transmission case.
    • Fig 4: Identifying Turbine Revolution Sensor Hole And Brake Band
      G02250192Courtesy of NISSAN MOTOR CO., U.S.A.
    • Assemble it so that manual valve cutout is engaged with manual plate projection.
  8. Fig 5: Identifying Manual Plate And Valve
    G02250193Courtesy of NISSAN MOTOR CO., U.S.A.
  9. Install bolts A, B and C in control valve with TCM.
  10. Fig 6: Control Valve Bolt Specifications
    G02250194Courtesy of NISSAN MOTOR CO., U.S.A.
    Fig 7: Identifying Control Valve With TCM Bolts
    G02250195Courtesy of NISSAN MOTOR CO., U.S.A.
  11. Tighten bolt 1, 2 and 3 temporarily to prevent dislocation. After that tighten them in order (1 --> 2 --> 3), and then tighten other bolts.
  12. Tighten control valve with TCM mounting bolts to the specified torque. Refer to COMPONENTS .
  13. Fig 8: Bolt Tightening Sequence
    G02250196Courtesy of NISSAN MOTOR CO., U.S.A.
  14. Connect A/T fluid temperature sensor 2 connector.
  15. Fig 9: Identifying A/T Fluid Temperature Sensor 2 Connector
    G02250197Courtesy of NISSAN MOTOR CO., U.S.A.
  16. Securely fasten A/T fluid temperature sensor 2 harness with terminal clip.
  17. Fig 10: Identifying A/T Fluid Temperature Sensor 2 Harness And Terminal Clip
    G02250198Courtesy of NISSAN MOTOR CO., U.S.A.
  18. Connect revolution sensor connector.
  19. Fig 11: Connecting Revolution Sensor Connector
    G02250199Courtesy of NISSAN MOTOR CO., U.S.A.
  20. Securely fasten revolution sensor harness with terminal clips.
  21. Fig 12: Attaching Terminal Clips To Revolution Sensor Harness
    G02250200Courtesy of NISSAN MOTOR CO., U.S.A.
  22. Install magnets in oil pan.
  23. Fig 13: Installing Magnets In Oil Pan
    G02250201Courtesy of NISSAN MOTOR CO., U.S.A.
  24. Install oil pan to transmission case.
    1. Install oil pan gasket to oil pan.
      CAUTION:
      • Do not reuse oil pan gasket.
      • Install it in the direction to align hole positions.
      • Complete remove all moisture, oil and old gasket, etc. From oil pan gasket mounting surfaces.
    2. Install oil pan (with oil pan gasket) to transmission case.
      CAUTION:
      • Install It so that drain plug comes to the position as shown in Fig 14.
      • Be careful not to pinch harnesses.
      • Complete remove all moisture, oil and old gasket, etc. From oil pan mounting surfaces.
    3. Fig 14: Locating Oil Pan Bolts
      G02250202Courtesy of NISSAN MOTOR CO., U.S.A.
    4. Tighten oil pan mounting bolts to the specified torque in numerical order shown in Fig 15 after temporarily tightening them. Refer to COMPONENTS .
      CAUTION: Do not reuse oil pan mounting bolts.
  25. Install drain plug to oil pan. Tighten drain plug to the specified torque. Refer to COMPONENTS .
    CAUTION: Do not reuse drain plug gasket.
  26. Fig 15: Oil Pan Mounting Bolts Tightening Sequence
    G02250203Courtesy of NISSAN MOTOR CO., U.S.A.
  27. Pull up A/T assembly harness connector.
    CAUTION: Be careful not to damage connector.
  28. Fig 16: Identifying A/T Assembly Harness Connector
    G02250204Courtesy of NISSAN MOTOR CO., U.S.A.
  29. Install snap ring to A/T assembly harness connector.
  30. Connect A/T assembly harness connector.
  31. Pour ATF into transmission assembly. Refer to CHANGING A/T FLUID .
  32. Connect the negative battery terminal
Fig 17: Installing Snap Ring To A/T Assembly Harness Connector
G02250205Courtesy of NISSAN MOTOR CO., U.S.A.