LEMON Manuals: Even more car manuals for everyone

Repair Procedures: Removal

CAUTION:
  • When the solenoid valve Diagnostic Trouble Codes (DTC) is on, perform the following procedure to replace it.
  • Automatic transaxle is composed of delicate components. Be careful not to cause any damage on the component in the course of assembly and disassembly.
  • Maintain clean condition so that foreign substance does not get into the automatic transaxle.
  • Use a coated apron, latex gloves, and stainless tray to prevent foreign substance from getting into the transaxle.
  • Automatic transaxle fluid (ATF) can be reused. Collect it using a clean 10-liter beaker.
  1. Turn ignition switch OFF and disconnect the negative (-) battery cable.
  2. Remove the air duct and air cleaner assembly.

    (Refer to Engine Mechanical System - "AIR CLEANER "

  3. Discharge the coolant. (if equipped ATF warmer)
  4. Remove the drain plug (A) and drain the ATF totally and then reinstall the drain plug.
    Fig 1: Removing Drain Plug
    G12025247Courtesy of HYUNDAI MOTOR AMERICA
  5. Remove the battery and battery tray.

    (Refer to Engine Electrical System - "BATTERY ")

  6. Disconnect the connector (A).
    Fig 2: Disconnecting Connector
    G12025410Courtesy of HYUNDAI MOTOR AMERICA
  7. Disconnect the wiring fixing clip (A).
  8. Disconnect the air bleeder hose (B).
    Fig 3: Locating Wiring Fixing Clip And Air Bleeder Hose
    G12025411Courtesy of HYUNDAI MOTOR AMERICA
  9. Disconnect the ATF cooler hoses (A).
    Fig 4: Disconnecting ATF Cooler Hoses
    G12025412Courtesy of HYUNDAI MOTOR AMERICA
    CAUTION:
    • Be careful not to cause any damage on the hose when tightening the clamp.
    • Mount the clamp tightening part in the designated direction so that interference does not occur with the adjacent parts.
    • After connecting the hose, check for oil leakage on the connecting part while the engine is on.
  10. Disconnect the ATF warmer hoses (A).
  11. Remove the heater pipe mounting bolt (B).
    Fig 5: Locating ATF Warmer Hoses And Heater Pipe Mounting Bolt
    G12025413Courtesy of HYUNDAI MOTOR AMERICA
    CAUTION:
    • Be careful not to cause any damage on the hose when tightening the clamp.
    • Mount the clamp tightening part in the designated direction so that interference does not occur with the adjacent parts.
    • After connecting the hose, check for oil leakage on the connecting part while the engine is on.
  12. Unscrew the bolts and remove the valve body cover (A).

    Tightening torque: 

    11.8 - 13.7 N.m (1.2 - 1.4 kgf.m, 8.7 - 10.1 lb-ft)

    Fig 6: Removing Valve Body Cover (1 Of 2)
    G12025414Courtesy of HYUNDAI MOTOR AMERICA
    Fig 7: Removing Valve Body Cover (2 Of 2)
    G12025415Courtesy of HYUNDAI MOTOR AMERICA
    CAUTION:
    • When re-mounting the valve body cover, replace the gasket with a new one.
    • After mounting the valve body cover, check for oil leakage on the connecting part while the engine is on.
      Fig 8: Replacing Gasket
      G12025416Courtesy of HYUNDAI MOTOR AMERICA
  13. Unscrew the bolts and disconnect the solenoid valve connector (A).

    Tightening torque: 

    9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb-ft)

    Fig 9: Disconnecting Solenoid Valve Connector
    G12025417Courtesy of HYUNDAI MOTOR AMERICA
  14. Remove the support bracket mounting bolts (A).

    Tightening torque: 

    9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb-ft)

    Fig 10: Removing Support Bracket Mounting Bolts
    G12025418Courtesy of HYUNDAI MOTOR AMERICA
  15. Remove the support bracket (A).
    Fig 11: Removing Support Bracket
    G12025419Courtesy of HYUNDAI MOTOR AMERICA
  16. Remove the on/off solenoid valve (A).
    Fig 12: Removing On/Off Solenoid Valve
    G12025420Courtesy of HYUNDAI MOTOR AMERICA
    CAUTION:
    • When installing, apply the ATF oil or white vaseline to the O-rings (A) not to be damaged.
    Fig 13: Locating O-Rings
    G12025421Courtesy of HYUNDAI MOTOR AMERICA