LEMON Manuals: Even more car manuals for everyone

Repair Procedures: Removal

CAUTION:
  • Use fender covers to avoid damaging painted surfaces.
  • To avoid damage, unplug the wiring connectors carefully while holding the connector portion.
WARNING: For release the fuel pressure, start the engine and wait until fuel in fuel line is exhausted. After the engine stop turn the ignition switch OFF.
NOTE:
  • Mark all wiring and hoses to avoid mis-connection.
  1. Disconnect the battery negative cable (A).
  2. Remove the transmission before removing the engine. (Refer to AUTOMATIC TRANSMISSION SYSTEM - 3.8L or MANUAL TRANSMISSION SYSTEM - M6VR2 )
  3. Remove the strut bar (B).
    Fig 1: Identifying Battery Negative Cable & Strut Bar
    G06511196Courtesy of HYUNDAI MOTOR CO.
  4. Loosen the drain plug and drain the engine coolant.
  5. After recovering refrigerant, remove the high & low pressure pipe. (Refer to AIR CONDITIONING SYSTEM )
  6. Remove the air duct (A).
  7. Remove the air cleaner assembly (C) after removing the AFS connector (B).

    Tightening torque: 

    Bolt: 7.8 ~ 9.8N.m (0.8 ~ 1.0kgf.m, 5.8 ~ 7.2lb-ft)

    Clamp: 2.9 ~ 4.9N.m (0.3 ~ 0.5kgf.m, 2.2 ~ 3.6lb-ft)

    Fig 2: Identifying Air Duct, Air Cleaner Assembly, & AFS Connector
    G06511197Courtesy of HYUNDAI MOTOR CO.
  8. Remove the radiator upper hose (A).
    Fig 3: Identifying Radiator Upper Hose
    G06511198Courtesy of HYUNDAI MOTOR CO.
  9. Remove the radiator lower hose (B).
    Fig 4: Identifying Radiator Lower Hose
    G06511199Courtesy of HYUNDAI MOTOR CO.
  10. Disconnect the fuel hoses (B) and brake vacuum hose (A).
    Fig 5: Identifying Fuel Hoses & Brake Vacuum Hose
    G06511200Courtesy of HYUNDAI MOTOR CO.
  11. Remove the cooling fan.
    1. Remove the cooling fan connector (A).
    2. Remove the reservoir tank (B).
    3. Remove the fan assembly (C).
      Fig 6: Identifying Cooling Fan Connector, Reservoir Tank, & Fan Assembly
      G06511201Courtesy of HYUNDAI MOTOR CO.
  12. Remove the oil hose from the power steering pump. (Refer to HYDRAULIC POWER STEERING SYSTEM )
  13. Disconnect the ECM connector (A), brake oil level sensor connector (B) and ground (C).
    Fig 7: Identifying ECM Connector, Brake Oil Level Sensor Connector, & Ground
    G06511202Courtesy of HYUNDAI MOTOR CO.
  14. Remove the alternator cable. (Refer to CHARGING SYSTEM (ENGINE ELECTRICAL SYSTEM) - 3.8L )
  15. Disconnect the wirings (A) from the fuse box.
    Fig 8: Identifying Wirings
    G06511203Courtesy of HYUNDAI MOTOR CO.
  16. Remove the heater hoses (A).
    Fig 9: Identifying Heater Hoses
    G06511204Courtesy of HYUNDAI MOTOR CO.
  17. Remove the engine mounting bracket nuts (A).

    Tightening torque: 

    66.7 ~ 83.4N.m (6.8 ~ 8.5kgf.m, 49.2 ~ 61.5lb-ft)

    [LH] 

    Fig 10: Identifying LH Engine Mounting Bracket Nut
    G06511205Courtesy of HYUNDAI MOTOR CO.

    [RH] 

    Fig 11: Identifying RH Engine Mounting Bracket Nut
    G06511206Courtesy of HYUNDAI MOTOR CO.
  18. Remove the hood. (Refer to HOOD )
  19. Remove the engine assembly by lifting the engine jack.
    Fig 12: Removing Engine Assembly
    G06511207Courtesy of HYUNDAI MOTOR CO.
    CAUTION:
    • When removing the engine assembly, be careful not to damage any surrounding parts or body components.