LEMON Manuals: Even more car manuals for everyone

Repair Procedures: Installation

  1. Temporarily install the transmission assembly by lifting the supporting jack.
    CAUTION: Be careful not to damage tubes, hoses, or wire.
  2. Install the mounting bolts (A-2ea) on the transmission.

    Tightening torque: 

    65~85 Nm (6.5~8.5 kgf.m, 47.0~61.5 lb-ft)

    Fig 1: Identifying Mounting Bolts
    G06509824Courtesy of HYUNDAI MOTOR CO.
  3. Install the starter motor mounting bolt (A) and nut (B).

    Tightening torque: 

    [A]50~65 Nm (5.0~6.5 kgf.m, 36.2~47.0 lb-ft)

    [B]43~55 Nm (4.3~5.5 kgf.m, 31.1~39.8 lb-ft)

    Fig 2: Identifying Starter Motor Mounting Bolt & Nut
    G06509825Courtesy of HYUNDAI MOTOR CO.
  4. Install the mounting bolts (2ea) left in the engine side.

    Tightening torque: 

    [A]65~85 Nm (6.5~8.5 kgf.m, 47.0~61.5 lb-ft)

    [B]35~47 Nm (3.5~4.7 kgf.m, 25.3~34.0 lb-ft)

    Fig 3: Identifying Mounting Bolts
    G06509826Courtesy of HYUNDAI MOTOR CO.
  5. Install the mounting bolts (A-4ea) lower in the engine side.

    Tightening torque: 

    40~47 Nm (4.0~4.7 kgf.m, 28.9~34.0 lb-ft)

    Fig 4: Identifying Mounting Bolts
    G06509827Courtesy of HYUNDAI MOTOR CO.
  6. Install the torque converter mounting bolts (A-6ea) by rotating the crankshaft.

    Tightening torque: 

    46~53 Nm (4.6~5.3 kgf.m, 31.1~39.8 lb-ft)

    Fig 5: Identifying Torque Converter Mounting Bolts
    G06509828Courtesy of HYUNDAI MOTOR CO.
  7. Install the dust cover (A) by installing a nut.
    Fig 6: Identifying Dust Cover
    G06509829Courtesy of HYUNDAI MOTOR CO.
  8. Install the crossmember (A) to the vehicle by installing bolts (4ea) and put aside the supporting jack.

    Tightening torque: 

    50~65 Nm (5.0~6.5 kgf.m, 36.2~47.0 lb-ft)

    Fig 7: Identifying Crossmember
    G06509830Courtesy of HYUNDAI MOTOR CO.
  9. Install the under shield cover (A).
    Fig 8: Identifying Under Shield Cover
    G06509831Courtesy of HYUNDAI MOTOR CO.
  10. Install the oil cooler tube assembly (A) by installing a bolt.
    NOTE: Install a bolt (B) on the subframe.
    Fig 9: Identifying Oil Cooler Tube Assembly
    G06509832Courtesy of HYUNDAI MOTOR CO.
  11. Install the propeller shaft to the transmission by installing bolts (A-3ea).

    Tightening torque: 

    90~110 Nm (9~11 kgf.m, 65.1~79.5 lb-ft)

    Fig 10: Identifying Propeller Shaft Bolts
    G06509833Courtesy of HYUNDAI MOTOR CO.
  12. Install the ground wires and wire holding brackets.
    Fig 11: Identifying Ground Wires & Wire Holding Brackets
    G06509834Courtesy of HYUNDAI MOTOR CO.
  13. Install the CKP sensor (A) by installing a bolt.
    Fig 12: Identifying CKP Sensor
    G06509835Courtesy of HYUNDAI MOTOR CO.
  14. Install the shift cable assembly (C) by installing the bracket bolts (A-2ea) and a nut (B).

    Tightening torque: 

    [A]10~12 Nm (1.0~1.2kgf.m, 7.23~8.68 lb-ft)

    [B]17~26 Nm (1.7~2.6kgf.m, 12.3~18.8 lb-ft)

    CAUTION: Place the manual lever in N position and check if the shift lever is in N position.
    Fig 13: Identifying Shift Cable Assembly, Bracket Bolts & Nut
    G06509836Courtesy of HYUNDAI MOTOR CO.
  15. Install the front muffler assembly. (refer to INTAKE AND EXHAUST SYSTEM (ENGINE MECHANICAL) - 3.8L )
  16. Connect the TCU connector (A).
    Fig 14: Identifying TCU Connector
    G06509837Courtesy of HYUNDAI MOTOR CO.
  17. Install the ground wire (A) by installing a bolt.
    Fig 15: Identifying Ground Wire
    G06509838Courtesy of HYUNDAI MOTOR CO.
  18. Connect (-) terminal to the battery.
    Fig 16: Connecting (-) Terminal To Battery
    G06509839Courtesy of HYUNDAI MOTOR CO.
  19. Check the level of oil fluid. (refer to PROCEDURE OF ATF LEVEL ADJUSTMENT )