LEMON Manuals: Even more car manuals for everyone

A/C Compressor Assembly Inspection And Replacement (Service Campaign TC2) (SC TC2)

Publication date: 2010-08-01
Reference number: SC TC2
Supersedes refnos: 10-01-028

A/C COMPRESSOR ASSEMBLY INSPECTION AND REPLACEMENT (SERVICE CAMPAIGN TC2)

A/C COMPRESSOR ASSEMBLY INSPECTION AND REPLACEMENT (SERVICE CAMPAIGN TC2)

SERVICE CAMPAIGN BULLETIN

Reference Number(s): 10-01-028, Date of Issue:  August, 2010
HYUNDAI: 2010 TUCSON
GROUP: CAMPAIGN

REVISION HISTORY

IMPORTANT: DEALERS MUST PERFORM THIS CAMPAIGN ON ALL AFFECTED VEHICLES PRIOR TO CUSTOMER RETAIL DELIVERY AND WHENEVER AN AFFECTED VEHICLE IS IN THE SHOP FOR ANY MAINTENANCE OR REPAIR.
IMPORTANT: WHEN A VEHICLE ARRIVES AT THE SERVICE DEPARTMENT, ACCESS HYUNDAI MOTOR AMERICA'S "WARRANTY VEHICLE INFORMATION" SCREEN VIA WEBDCS TO IDENTIFY OPEN CAMPAIGNS.

DESCRIPTION

This bulletin provides information related to the A/C compressor assemblies of some 2010MY Tucson (LM) vehicles to ensure proper operation.

The information is outlined in this bulletin as follows:

APPLICABLE VEHICLES

APPLICABLE VEHICLES

MODEL VEHICLE PRODUCTION DATE
2010 Tucson (LM) From: May 12, 2010
To: May 24, 2010

PARTS INFORMATION

PARTS INFORMATION

PART NAME PART NO. FIGURE
A/C Compressor Assembly 97701-2S500
G09241808
A/C Suction Pipe O-ring 97690-34610
G09241809
A/C Disharge Hose O-ring 97690-34630
G09241810

INSPECTION PROCEDURE

  1. Lift the vehicle.
  2. Remove the under cover (A) by unfastening 9 clips and 5 bolts.
    • Tightening torque: 2.0~2.5 kgf.m (19.6~24.5 Nm, 14.4~18.0 lbf.ft)
  3. Locate the A/C compressor label and check the lot number (B).
    G09241811
    G09241812
    • If the lot number is "OE11"  , then proceed to the REPLACEMENT PROCEDURE in the next section to replace the A/C Compressor Assembly with a new part.
    • If the lot number is not affected, then no further procedure is required.
      • Reinstall the under cover and submit campaign claim for A/C Compressor Lot Number Inspection  .

REPLACEMENT PROCEDURE

  1. Remove the refrigerant filler cap (A).
    G09241813
  2. Recover all refrigerant with an A/C recovery/charging station.
  3. Remove the engine side cover (B).
    • Turn the steering wheel fully to the right to gain access to the engine side cover without having to remove the right-front wheel/tire assembly.
    • Tightening torque: 2.0~2.5 kgf.m (19.6~24.5 Nm, 14.4~18.0 lbf.ft)
  4. Disconnect the A/C clutch wiring connector (C).
    G09241814
  5. Remove the A/C suction pipe mounting bolt (D) and A/C discharge hose mounting bolts (E).
    NOTE: After disconnecting the lines, immediately plug or cap them to prevent moisture and dust contamination.
  6. Loosen the drive belt by slightly turning the idler (F) counter-clockwise and partially remove the drive belt on the A/C compressor pulley.
  7. Remove the A/C compressor assembly mounting bolts (G).
    • Tightening torque: 2.0~2.5 kgf.m (19.6~24.5 Nm, 14.4~18.0 lbf.ft)
  8. Remove the A/C compressor assembly (H).
  9. Install the new A/C compressor assembly in reverse order of removal.
    IMPORTANT:
    • When reinstalling the lines, replace the O-rings with new ones.
      G09241815
    • Always apply refrigerant (PAG) oil to the new O-rings prior to installation.
      G09241816
      G09241817
  10. Charge the A/C system with refrigerant.
    • Refrigerant charge amount: 510 ± 25 grams
  11. Verify repair.
NOTE: Confirm that the vented air is cold during A/C operation.

WARRANTY INFORMATION

WARRANTY INFORMATION

OP CODE OPERATION OP TIME
00C04811 A/C Compressor Lot Number Inspection 0.3 M/H
00C048R1 A/C Compressor Lot Number Inspection&Replacement 1.0 M/H
NOTE: Submit claim on Campaign Claim Entry Screen.