LEMON Manuals: Even more car manuals for everyone

Battery Test Procedure

  1. Connect the tester to the battery.
    1. Red clamp to battery positive (+) terminal.
    2. Black clamp to battery negative (-) terminal.
      Fig 1: Connecting Tester To Battery
      G06873080Courtesy of HYUNDAI MOTOR CO.
      CAUTION: Connect clamps securely. If "CHECK CONNECTION" message is displayed on the screen, reconnect clamps securely.
  2. The tester will ask if the battery is connected "IN-VEHICLE" or "OUT-OF-VEHICLE". Make your selection by pressing the arrow buttons; then press ENTER.
    Fig 2: Screen Display - IN-VEHICLE
    G06873081Courtesy of HYUNDAI MOTOR CO.
  3. Select CCA and press the ENTER button.
    Fig 3: Screen Display - CCA
    G06873082Courtesy of HYUNDAI MOTOR CO.
    NOTE: CCA: Cold cranking amps, is an SAE specification for cranking batteries at -0.4°F (-18°C).
  4. Set the CCA value displayed on the screen to the CCA value marked on the battery label by pressing up and down buttons and press ENTER.
    Fig 4: Screen Display - SET RATING
    G06873083Courtesy of HYUNDAI MOTOR CO.
    NOTE: The battery ratings (CCA) displayed on the tester must be identical to the ratings marked on battery label.
  5. The tester will conduct battery test.
    Fig 5: Screen Display - TESTING
    G06873084Courtesy of HYUNDAI MOTOR CO.
  6. The tester displays battery test results including voltage and battery ratings.

    A relevant action must be given according to the test results by referring to the BATTERY TEST  results as shown in the table below.

    Fig 6: Screen Display - BATTERY CONDITION
    G06873085Courtesy of HYUNDAI MOTOR CO.
  7. To conduct starter test, continuously, press ENTER.

    Battery Test Results 

    BATTERY TEST RESULT CHART

    Result On Printer Remedy
    GOOD BATTERY No action is required
    GOOD RECHARGE Battery is in a good state
    Recharge by running engine 20 minutes at with no accessories on.
    Retest to assure good.
    CHARGE & RETEST Battery is not charged properly
    • Charge and test the battery again (Failure to charge the battery fully may read incorrect measurement value)
    REPLACE BATTERY
    • Replace battery and recheck the charging system. (Improper connection between battery and vehicle cables may cause "REPLACE BATTERY", retest the battery after removing cables and connecting the tester to the battery terminal directly prior to replacing the battery)
    BAD CELL-REPLACE
    • Charge and retest the battery. And than, test results may cause "REPLACE BATTERY", replace battery and recheck the charging system
    WARNING: Whenever filing a claim for battery, the print out of the battery test results must be attached.

    Starter Test Procedure 

  8. After the battery test, press ENTER immediately for the starter test.
    Fig 7: Screen Display - PRESS ENTER FOR STARTER TEST
    G06873086Courtesy of HYUNDAI MOTOR CO.
  9. Start the engine.
    Fig 8: Screen Display - START ENGINE
    G06873087Courtesy of HYUNDAI MOTOR CO.
  10. Cranking voltage and starter test results will be displayed on the screen.

    Take a relevant action according to the test results by referring to the starter test results as given below.

    Fig 9: Screen Display - CRANKING VOLTAGE
    G06873088Courtesy of HYUNDAI MOTOR CO.

    Starter Test Results 

    STARTER TEST RESULT CHART

    Result On Printer Remedy
    CRANKING VOLTAGE NORMAL System shows a normal starter draw
    CRANKING VOLTAGE LOW Cranking voltage is lower than normal level
    • Check starter
    CHARGE BATTERY The state of battery charge is too low to test
    • Charge the battery and retest
    REPLACE BATTERY
    • Replace battery
    • If the vehicle is not started though the battery condition of "GOOD BATTERY" is displayed.
    • Check wiring for open circuit, battery cable connection, starter and repair or replace as necessary.
    • If the engine does crank, check fuel system.
    NOTE: When testing the vehicle with old diesel engines, the test result will not be favorable if the glow plug is not heated. Conduct the test after warming up the engine for 5 minutes.

    Charging System Test Procedure 

  11. Press ENTER to begin charging system test.
    Fig 10: Screen Display - PRESS ENTER FOR CHARGING TEST
    G06873089Courtesy of HYUNDAI MOTOR CO.
  12. The tester displays the actual voltage of alternator.

    Press ENTER to continue.

    Fig 11: Screen Display - ALTERNATOR VOLTAGE
    G06873090Courtesy of HYUNDAI MOTOR CO.
  13. Turn off all electrical load and rev engine for 5 seconds with pressing the accelerator pedal. (Follow the instructions on the screen)
    Fig 12: Screen Display - LOADS OFF REV ENGINE 5 SEC
    G06873091Courtesy of HYUNDAI MOTOR CO.
    Fig 13: Screen Display - INCREASE REV
    G06873092Courtesy of HYUNDAI MOTOR CO.
    Fig 14: Screen Display - HOLD REV
    G06873093Courtesy of HYUNDAI MOTOR CO.
  14. The message that engine RPM is detected will be displayed on the screen. Press ENTER to continue.
    Fig 15: Screen Display - RPM DETECTED ENTER TO CONTINUE
    G06873094Courtesy of HYUNDAI MOTOR CO.
  15. If the engine RPM is not detected, press ENTER after revving engine.
    Fig 16: Screen Display - ENTER TO CONT AFTER REVVING
    G06873095Courtesy of HYUNDAI MOTOR CO.
  16. The tester will conduct charging system during loads off.
    Fig 17: Screen Display - TESTING
    G06873096Courtesy of HYUNDAI MOTOR CO.
    Fig 18: Screen Display - TESTING
    G06873097Courtesy of HYUNDAI MOTOR CO.
  17. Turn on electrical loads (air conditioner, lamps, audio and etc). Press ENTER to continue.
    Fig 19: Screen Display - TURN ON ELECTRICAL LOADS
    G06873098Courtesy of HYUNDAI MOTOR CO.
  18. The tester will conduct charging system during loads on.
    Fig 20: Screen Display - TESTING
    G06873099Courtesy of HYUNDAI MOTOR CO.
  19. Rev engine for 5 seconds with pressing the accelerator pedal. (Follow the instructions on the screen)
    Fig 21: Screen Display - LOADS ON REV ENGINE 5 SEC
    G06873100Courtesy of HYUNDAI MOTOR CO.
    Fig 22: Screen Display - INCREASE REV
    G06873101Courtesy of HYUNDAI MOTOR CO.
    Fig 23: Screen Display - HOLD REV
    G06873102Courtesy of HYUNDAI MOTOR CO.
  20. The message that engine RPM is detected will be displayed on the screen. Press ENTER to continue.
    Fig 24: Screen Display - RPM DETECTED ENTER TO CONTINUE
    G06873103Courtesy of HYUNDAI MOTOR CO.
  21. If the engine RPM is not detected, press ENTER after revving engine.
    Fig 25: Screen Display - ENTER TO CONT AFTER REVVING
    G06873104Courtesy of HYUNDAI MOTOR CO.
  22. Turn off electrical loads (air conditioner, lamps, audio and etc). Turn the engine off.
    Fig 26: Screen Display - TURN OFF ELECTRICAL LOADS
    G06873105Courtesy of HYUNDAI MOTOR CO.
  23. Charging voltage and charging system test results will be displayed on the screen.

    Take a relevant action according to the test results by referring to the table below after shutting off the engine and disconnect the tester clamps from the battery.

    Fig 27: Screen Display - Charging System
    G06873106Courtesy of HYUNDAI MOTOR CO.
    Fig 28: Screen Display - DIODE RIPPLE NORMAL
    G06873107Courtesy of HYUNDAI MOTOR CO.
    Fig 29: Screen Display - CHARGING SYSTEM NORMAL
    G06873108Courtesy of HYUNDAI MOTOR CO.

    Charging System Test Results 

    CHARGING SYSTEM TEST RESULT CHART

    Result On Printer Remedy
    CHARGING SYSTEM NORMAL / DIODE RIPPLE NORMAL Charging system is normal
    NO CHARGING VOLTAGE Alternator does not supply charging current to battery
    • Check belts, connection between alternator and battery

    Replace belts or cable or alternator as necessary
    LOW CHARGING VOLTAGE Alternator does not supply charging current to battery and electrical load to system fully
    • Check belts and alternator and replace as necessary
    HIGH CHARGING VOLTAGE The voltage from alternator to battery is higher than normal limit during voltage regulating.
    • Check connection and ground and replace regulator as necessary
    • Check electrolyte level in the battery
    EXCESS RIPPLE DETECTED One or more diodes in the alternator is not functioning properly
    • Check alternator mounting and belts and replace as necessary