LEMON Manuals: Even more car manuals for everyone

DTC P0812: Open in Transmission Range Switch ATPR Switch Circuit

NOTE:
  • Before you troubleshoot, record all freeze data and any on-board snapshot with the HDS, and review General Troubleshooting Information (see GENERAL TROUBLESHOOTING INFORMATION  ).
  • This code is caused by an electrical circuit problem and cannot be caused by a mechanical problem in the transmission.
  1. Turn the ignition switch to ON (II).
  2. Shift the shift lever into R, and check the A/T R SWITCH with the HDS in the A/T Data List.

    Is the A/T R SWITCH ON? 

    YES  -Intermittent failure, the system is OK at this time.

    NO  -Go to step 3.

  3. Turn the ignition switch to LOCK (0).
  4. Disconnect the transmission range switch connector.
  5. Turn the ignition switch to ON (II).
  6. Measure the voltage between transmission range switch connector terminals No. 6 and No. 8.
    Fig 1: Measuring Voltage Between Transmission Range Switch Connector Terminals No. 6 And No. 8
    G06680745Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there battery voltage? 

    YES  -Go to step 7.

    NO  -Repair open in the wire between the transmission range switch and PCM connector terminal C25, then go to step  8.

  7. Check for continuity between the No. 6 and No. 8 terminals at the transmission range switch.
    Fig 2: Checking Continuity Between No. 6 And No. 8 Terminals At Transmission Range Switch
    G06680746Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there continuity when the shift lever is in R, and no continuity when the shift lever is in any position other than R? 

    YES  -Go to step  14.

    NO  -Replace the transmission range switch (see TRANSMISSION RANGE SWITCH REPLACEMENT  ), then go to step 8.

  8. Reconnect all connectors.
  9. Turn the ignition switch to ON (II).
  10. Clear the DTC with the HDS.
  11. Test-drive the vehicle in R at speeds below 3 mph (5 km/h) for at least 2 seconds, then increase the speed and test-drive at speeds over 3 mph (5 km/h) for at least 2 seconds.
  12. Check for Pending or Confirmed DTCs with the HDS.

    Is DTC P0812 indicated? 

    YES  -Check for poor connections or loose terminals between the transmission range switch and the PCM, then go to step  1.

    NO  -Go to step 13.

  13. Monitor the OBD STATUS for P0812 in the DTCs MENU with the HDS.

    Does the HDS indicate PASSED? 

    YES  -Troubleshooting is complete. If any other Pending or Confirmed DTCs were indicated in step  12, go to the INDICATED DTC'S TROUBLESHOOTING .

    NO  -If the HDS indicates FAILED, check for poor connections or loose terminals between the transmission range switch and the PCM, then go to step  1. If the HDS indicates NOT COMPLETED, go to step  11.

  14. Reconnect all connectors.
  15. Update the PCM if it does not have the latest software (see PCM UPDATE ), or substitute a known-good PCM (see SUBSTITUTING THE PCM ).
  16. Test-drive the vehicle in R at speeds below 3 mph (5 km/h) for at least 2 seconds, then increase the speed and test-drive at speeds over 3 mph (5 km/h) for at least 2 seconds.
  17. Check for Pending or Confirmed DTCs with the HDS.

    Is DTC P0812 indicated? 

    YES  -Check for poor connections or loose terminals between the transmission range switch and the PCM. If the PCM was updated, substitute a known-good PCM (see SUBSTITUTING THE PCM ), then go to step  16. If the PCM was substituted, go to step  1.

    NO  -Go to step 18.

  18. Monitor the OBD STATUS for P0812 in the DTCs MENU with the HDS.

    Does the HDS indicate PASSED? 

    YES  -If the PCM was updated, troubleshooting is complete. If the PCM was substituted, replace the original PCM (see PCM REPLACEMENT ). If any other Pending or Confirmed DTCs were indicated in step  17, go to the INDICATED DTC'S TROUBLESHOOTING .

    NO  -If the HDS indicates FAILED, check for poor connections or loose terminals between the transmission range switch and the PCM. If the PCM was updated, substitute a known-good PCM (see SUBSTITUTING THE PCM ), then go to step  16. If the PCM was substituted, go to step  1. If the HDS indicates NOT COMPLETED, go to step  16.