LEMON Manuals: Even more car manuals for everyone

DTC P1457: EVAP Control System Leakage (EVAP Canister System)

NOTE: The fuel system is designed to allow specified maximum vacuum and pressure conditions. Do not deviate from the vacuum and pressure tests as indicated in these procedures. Excessive pressure/vacuum would damage the EVAP components or cause eventual fuel tank system failure.

Special Tools Required 

  1. Vacuum pump/gauge, 0-30 in.Hg A973X-041-XXXXX

This is a two-trip code; Once cleared, it cannot be reproduced in one trip. Also certain specific driving and ambient conditions must occur before the ECM/PCM will complete the system checks. Additional test drives may still not meet the specific conditions needed to reproduce the code.

Follow these troubleshooting procedures carefully to ensure the integrity of the system and to confirm the cause of the problem or code.

NOTE: Fresh fuel has a higher volatility that will create greater pressure/vacuum. The optimum condition for testing is fresh fuel, and there must be less than a full tank of fuel. If possible, to assist in leak detection, add one gallon of fresh fuel to the tank (as long as it will not fill the tank), just before starting these procedures.

EVAP Canister Purge Valve Test 

  1. Disconnect the vacuum hose from the EVAP canister purge valve (A), and connect the vacuum pump to the hose.
    Fig 1: Connecting Vacuum Pump To Hose
    G02557485Courtesy of AMERICAN HONDA MOTOR CO., INC.
  2. Turn the EVAP canister purge valve on with the Honda PGM Tester, then connect ECM/PCM connector terminal A6 to body ground with a jumper wire.
    Fig 2: Connecting ECM/PCM Connector Terminal A6 To Body Ground With Jumper Wire
    G02557486Courtesy of AMERICAN HONDA MOTOR CO., INC.
  3. Turn the ignition switch ON (II).
  4. Apply vacuum to the hose.

    Does the valve hold vacuum? 

    1. YES  - Go to step 5.
    2. NO  - The EVAP canister purge valve is OK. Go to step  10.
  5. Turn the ignition switch OFF.
  6. Disconnect the EVAP canister purge valve 2P connector.
  7. Check for continuity between EVAP canister purge valve 2P connector terminal No. 2 and body ground.
    Fig 3: Checking Continuity Between EVAP Canister Purge Valve 2P Connector Terminal No. 2 & Body Ground
    G02557487Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there continuity? 

    1. YES  - Go to step 8.
    2. NO  - Repair open in the wire between the EVAP canister purge valve and ECM/PCM (A6).
  8. Turn the ignition switch ON (II).
  9. Measure voltage between EVAP canister purge valve 2P connector terminal No. 1 and body ground.
    Fig 4: Measuring Voltage Between EVAP Canister Purge Valve 2P Connector Terminal No. 1 & Body Ground
    G02557488Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there battery voltage? 

    1. YES  - Replace the EVAP canister purge valve.
    2. NO  - Repair open in the wire between the EVAP canister purge valve and No. 6 ECU (ECM/PCM) CRUISE CONTROL (15A) fuse.

      EVAP Bypass Solenoid Valve Test 

  10. Disconnect the vacuum hose from the EVAP two-way valve (A), and connect a vacuum pump to the hose.
    Fig 5: Connecting Vacuum Pump To Hose
    G02557489Courtesy of AMERICAN HONDA MOTOR CO., INC.
  11. Turn the ignition switch ON (II).
  12. Apply vacuum to the hose.

    Does the valve hold vacuum? 

    1. YES  - The EVAP bypass solenoid valve/EVAP two-way valve is OK. Go to step  18.
    2. NO  - Go to step 13.
  13. Turn the ignition switch OFF.
  14. Disconnect the EVAP bypass solenoid valve 2P connector.
  15. Check for continuity between EVAP bypass solenoid valve 2P connector terminal No. 2 and body ground.
    Fig 6: Checking Continuity Between EVAP Bypass Solenoid Valve 2P Connector Terminal No. 2 & Body Ground
    G02557490Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there continuity? 

    1. YES  - Go to step 16.
    2. NO  - Replace the EVAP bypass solenoid valve (A) and O-rings (B).
      Fig 7: Replacing EVAP Bypass Solenoid Valve & O-Rings
      G02557491Courtesy of AMERICAN HONDA MOTOR CO., INC.
  16. Disconnect ECM/PCM connector A (32P).
  17. Check for continuity between EVAP bypass solenoid valve 2P connector terminal No. 2 and body ground.
    Fig 8: Checking Continuity Between EVAP Bypass Solenoid Valve 2P Connector Terminal No. 2 & Body Ground
    G02557492Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there continuity? 

    1. YES  - Repair short in the wire between the EVAP bypass solenoid valve and ECM/PCM (A3).
    2. NO  - Substitute a known-good ECM/PCM and recheck (see HOW TO SUBSTITUTE THE ECM/PCM FOR TESTING PURPOSES ). If the symptom/indication goes away, replace the original ECM/PCM.

    EVAP Canister Vent Shut Valve Test 

  18. Disconnect the vacuum hose from the EVAP canister filter (A), and connect a vacuum pump to the hose.
    Fig 9: Connecting Vacuum Pump To Hose
    G02557493Courtesy of AMERICAN HONDA MOTOR CO., INC.
  19. With the Honda PGM Tester in the EVAP test mode, turn on the bypass solenoid, or connect ECM/PCM connector terminal A4 to body ground with a jumper wire.
    Fig 10: Connecting ECM/PCM Connector Terminal A4 To Body Ground With Jumper Wire
    G02557494Courtesy of AMERICAN HONDA MOTOR CO., INC.
  20. Turn the ignition switch ON (II)
  21. Apply vacuum to the hose.

    Does the valve hold vacuum? 

    1. YES  - The EVAP canister vent shut valve is OK. Go to step  27.
    2. NO  - Go to step 22.
  22. Turn the ignition switch OFF.
  23. Disconnect the EVAP canister vent shut valve 2P connector.
  24. Check for continuity between EVAP canister vent shut valve 2P connector terminal No. 2 and body ground.
    Fig 11: Checking Continuity Between EVAP Canister Vent Shut Valve 2P Connector Terminal No. 2 & Body Ground
    G02557495Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there continuity? 

    1. YES  - Go to step 25.
    2. NO  - Repair open in the wire between the EVAP canister vent shut valve and ECM/PCM (A4).
  25. Turn the ignition switch ON (II).
  26. Measure voltage between EVAP canister vent shut valve 2P connector terminal No. 1 and body ground.
    Fig 12: Measuring Voltage Between EVAP Canister Vent Shut Valve 2P Connector Terminal No. 1 & Body Ground
    G02557496Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there battery voltage? 

    1. YES  - Replace the EVAP canister vent shut valve (A) and O-ring (B).
    2. NO  - Repair open in the wire between the EVAP canister vent shut valve and No. 6 ECU (ECM/PCM) CRUISE CONTROL (15A) fuse.
      Fig 13: Replacing EVAP Canister Vent Shut Valve & O-Ring
      G02557497Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Canister System Leak Test 

  27. Turn the ignition switch OFF.
  28. Connect two three-way tee fittings (A) into the hose from the EVAP canister to the EVAP two-way valve. Connect the FTP sensor to one of the tee fittings and the vacuum pump to the other.
    Fig 14: Connecting FTP Sensor To One Of Tee Fittings & Vacuum Pump To Other
    G02557498Courtesy of AMERICAN HONDA MOTOR CO., INC.
  29. Remove the vent hose from the EVAP canister vent shut valve (A) and plug the port (B) to seal the fresh air vent for the EVAP canister.
    Fig 15: Removing Vent Hose From EVAP Canister Vent Shut Valve & Plugging Port
    G02557499Courtesy of AMERICAN HONDA MOTOR CO., INC.
  30. Turn the ignition switch ON (II).
  31. While monitoring the Fuel Tank Pressure (FTP) sensor voltage with the Honda PGM Tester, or measuring voltage between ECM/PCM connector terminals A 29 and C18, slowly pump the vacuum pump.
    Fig 16: Measuring Voltage Between ECM/PCM Connector Terminals A 29 & C18
    G02557500Courtesy of AMERICAN HONDA MOTOR CO., INC.
  32. Continue to pump until the voltage drops to about 1.5 V. Make sure your vacuum pump has no leak.
  33. Monitor the voltage for 20 seconds.

    Does the voltage drop to about 1.5 V and hold for at least 20 seconds? 

    1. YES  - Inspect the EVAP canister vent shut valve line and connections.
    2. NO  - Go to step 34.
  34. Turn the ignition switch OFF.
  35. Disconnect the quick-connect fitting (A) from the EVAP canister, and cap the canister port (B).
    Fig 17: Disconnecting Quick-Connect Fitting From EVAP Canister & Capping Canister Port
    G02557501Courtesy of AMERICAN HONDA MOTOR CO., INC.
  36. Turn the ignition switch ON (II).
  37. While monitoring FTP sensor voltage with the Honda PGM Tester, or measuring voltage between ECM/PCM connector terminals A29 and C18, slowly pump the vacuum pump.
    Fig 18: Measuring Voltage Between ECM/PCM Connector Terminals A29 & C18
    G02557502Courtesy of AMERICAN HONDA MOTOR CO., INC.
  38. Continue to pump vacuum until the voltage drops to about 1.5 V.
  39. Check the voltage for 20 seconds.

    Does the voltage drop to about 1.5 V and hold for least 20 seconds? 

    1. YES  - Inspect the fuel tank vapor line and connections for vacuum leaks.
    2. NO  - Go to step 40.
  40. Turn the ignition switch OFF.
  41. Disconnect the purge line hose (A) from the canister at the metal line and cap the canister port (B).
    Fig 19: Disconnecting Purge Line Hose From Canister At Metal Line & Capping Canister Port
    G02557503Courtesy of AMERICAN HONDA MOTOR CO., INC.
  42. Turn the ignition switch ON (II).
  43. While monitoring FTP sensor voltage with the Honda PGM Tester, or measuring voltage between ECM/PCM connector terminals A29 and C18, slowly pump the vacuum pump.
    Fig 20: Measuring Voltage Between ECM/PCM Connector Terminals A29 & C18
    G02557504Courtesy of AMERICAN HONDA MOTOR CO., INC.
  44. Continue to pump until the voltage drops to about 1.5 V. Make sure the engine coolant temperature is still above 95°F (35°C) and your vacuum pump has no leak.
  45. Monitor the voltage for 20 seconds.

    Does the voltage drop to about 1.5 V and hold for at least 20 seconds? 

    1. YES  - Inspect the EVAP canister purge valve line and connections for vacuum leaks. If they are OK, do the EVAP two-way valve test, and fuel tank vapor control valve test (see Fuel Tank Vapor Control Valve Test  ).
    2. NO  - Replace the EVAP canister.