Circuit/System Testing
Lockout Switch Inoperative
- Ignition OFF, disconnect the harness connector at the S79D Window Switch-Driver. Ignition ON
- Test for greater than 10 V between the signal circuit terminal 10 and ground.
- If 10 V or less
- Ignition OFF, disconnect the harness connector at the K9 Body Control Module.
- Test for infinite resistance between the signal circuit and ground.
- If less than infinite resistance, repair the short to ground on the circuit.
- Test for less than 2 Ω in the signal circuit end to end.
- If 2 Ω or greater, repair the open/high resistance in the circuit.
- If less than 2 Ω, replace the K9 Body Control Module.
- Go to next step: If greater than 10 V
- Test or replace the S79D Window Switch-Driver.
Lockout Indicator Malfunction
- Ignition OFF, disconnect the harness connector at the S79D Window Switch-Driver. Ignition ON.
- Test for greater than 1.5 V and less than 6 V between the control circuit terminal 11 and ground while operating the dimmer switch from the minimum to the maximum positions
- If 1.5 V or less
- Ignition OFF, disconnect the harness connector at the K9 Body Control Module.
- Test for infinite resistance between the control circuit and ground.
- If less than infinite resistance, repair the short to ground on the circuit.
- Test for less than 2 Ω in the signal circuit end to end.
- If 2 Ω or greater, repair the open/high resistance in the circuit.
- If less than 2 Ω, replace the K9 Body Control Module.
- If 6 V or greater
- Ignition OFF, disconnect the harness connector at the K9 Body Control Module.
- Test for less than 1 V between the control circuit and ground.
- If 1 V or greater, repair the short to voltage on the circuit.
- If less than 1 V, replace the K9 Body Control Module
- Go to next step: If greater than 1.5 V and less than 6 V
- Connect a test lamp between the control circuit terminal 12 and B+. Ignition ON
- Verify the test lamp turns ON and OFF when commanding the Child Security Lock Indicator Command Active and Inactive with a scan tool.
- If the test lamp is always OFF
- Ignition OFF, disconnect the harness connector at the K9 Body Control Module, ignition ON.
- Test for less than 1 V between the control circuit and ground.
- If 1 V or greater, repair the short to voltage on the circuit.
- Go to next step: If less than 1 V
- Ignition OFF.
- Test for less than 2 Ω in the control circuit end to end.
- If 2 Ω or greater, repair the open/high resistance in the circuit.
- If less than 2 Ω, replace the K9 Body Control Module.
- If the test lamp is always ON
- Ignition OFF, disconnect the harness connector at the K9 Body Control Module.
- Test for infinite resistance between the control circuit and ground.
- If less than infinite resistance, repair the short to ground on the circuit.
- If infinite resistance, replace the K9 Body Control Module.
- Go to next step: If the test lamp turns ON and OFF
- Test or replace the S79D Window Switch-Driver.
Security Child Lockout System Inoperative
- Ignition OFF and all vehicle systems OFF, disconnect the X1 harness connector at the X50A Fuse Block-Underhood. It may take up to 2 minutes for all vehicle systems to power down.
- Test for less than 10 Ω between the ground circuit terminal 71 and ground.
- If 10 Ω or greater
- Ignition OFF.
- Test for less than 2 Ω in the ground circuit end to end.
- If 2 Ω or greater, repair the open/high resistance in the circuit.
- If less than 2 Ω, repair the open/high resistance in the ground connection.
- Go to next step: If less than 10 Ω
- Ignition OFF, connect the X1 harness connector at the X50A Fuse Block-Underhood. Disconnect the X5 harness connector at the K9 Body Control Module, ignition ON.
- Verify that a test lamp does not illuminate between the control circuit terminal 16 and ground.
- If the test lamp illuminates
- Ignition OFF, disconnect the X2 harness connector at the X50A Fuse Block-Underhood.
- Test for less than 1 V between the K9 Body Control Module control circuit terminal 16 X5 and ground.
- If 1 V or greater, repair the short to voltage on the circuit.
- If less than 1 V, replace the X50A Fuse Block-Underhood.
- Go to next step: If the test lamp is not illuminated
- Connect a 3A fused jumper wire between the control circuit terminal 16 and B+.
- You should either hear or feel the KR113 Child Security Lock Disable Relay click as the relay activates.
- If the KR113 Child Security Lock Disable Relay does not activate
- Ignition OFF, remove the jumper wire, disconnect the X2 harness connector at the X50A Fuse Block-Underhood.
- Test for infinite resistance between the K9 Body Control Module control circuit terminal 16 X5 and ground.
- If less than Infinite resistance, repair the short to ground on the circuit.
- Go to next step: If infinite resistance
- Test for less than 2 Ω in the control circuit end to end.
- If 2 Ω or greater, repair the open/high resistance in the circuit.
- If less than 2 Ω, replace the X50A Fuse Block-Underhood.
- Go to next step: If the KR113 Child Security Lock Disable Relay activates
- Replace the K9 Body Control Module.
Single Door Security Lockout Malfunction
- Ignition OFF and all vehicle systems OFF, disconnect the harness connector at the appropriate A23 Door Latch Assembly-Rear. It may take up to 2 minutes for all vehicle systems to power down.
- Test for less than 10 Ω between the ground circuit terminal listed below and ground:
- A23RR Door Latch Assembly-Right Rear - ground circuit terminal 3
- A23LR Door Latch Assembly-Left Rear - ground circuit terminal 3
- If 10 Ω or greater
- Ignition OFF.
- Test for less than 2 Ω in the ground circuit end to end.
- If 2 Ω or greater, repair the open/high resistance in the circuit.
- If less than 2 Ω, repair the open/high resistance in the ground connection.
- Go to next step: If less than 10 Ω
- Ignition ON.
- Test for greater than 10 V between the signal circuit terminal listed below and ground:
- A23RR Door Latch Assembly-Right Rear - signal circuit terminal 4
- A23LR Door Latch Assembly-Left Rear - signal circuit terminal 2
- If 10 V or less
- Ignition OFF, disconnect the harness connector at the K9 Body Control Module.
- Test for infinite resistance between the signal circuit and ground.
- If less than infinite resistance, repair the short to ground on the circuit.
- Test for less than 2 Ω in the signal circuit end to end.
- If 2 Ω or greater, repair the open/high resistance in the circuit.
- If less than 2 Ω, replace the K9 Body Control Module.
- Go to next step: If greater than 10 V
- Install a DMM between the control circuit terminals listed below and ground. Set the DMM to capture DC voltage using the MIN MAX function. Turn off autorange and manually set the DMM range to 00.00 V.
- A23LR Door Latch Assembly-Left Rear - control circuit terminal 9
- A23RR Door Latch Assembly-Right Rear - control circuit terminal 7
- Command the Child Security Lock Motors to Lock and Unlock with a scan tool.
- Verify the MAX voltage captured by the DMM is greater than 10 V.
- If 10 V or less
- Ignition OFF, disconnect the X2 harness connector at the X50A Fuse Block - Underhood.
- Test for less than 2 Ω between the control circuit terminals listed below:
- X50A Fuse Block - Underhood control circuit terminal K8 X2 and A23LR Door Latch Assembly-Left Rear - control circuit terminal 9
- X50A Fuse Block - Underhood control circuit terminal K8 X2 and A23RR Door Latch Assembly-Right Rear - control circuit terminal 7
- If 2 Ω or greater, repair the open/high resistance on the circuit.
- Go to next step: If greater than 10 V
- Test or replace the A23 Door Latch Assembly-Rear.
NOTE:
When using the MIN MAX function, autorange on the DMM may not function properly. To ensure accurate test results, turn off autorange and manually set the DMM range to 00.00 V.