LEMON Manuals: Even more car manuals for everyone

Removal Procedure

    Fig 1: View Of Turbocharger Exhaust Pipe & Clamp
    GM668379Courtesy of GENERAL MOTORS COMPANY
  1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  2. Remove the exhaust manifold pipe to exhaust outlet clamp.
  3. Fig 2: Exhaust Manifold Pipe Hanger And Insulator (6.0L, 6.6L, and 8.1L Engines)
    GM694896Courtesy of GENERAL MOTORS COMPANY
  4. Remove the exhaust manifold pipe to catalytic pipe flange bolts.
  5. Slide the exhaust manifold pipe hanger from the insulator.
  6. Remove the exhaust pipe from the vehicle.
  7. Fig 3: View Of Fill Tube To Bellhousing Nuts
    GM702776Courtesy of GENERAL MOTORS COMPANY
  8. If equipped with an automatic transmission, remove the transmission fluid fill tube to bell housing nuts.
  9. Position the transmission fluid fill tube to the right side of the vehicle. The tube does not require removal from the transmission.
  10. Fig 4: View Of Right Exhaust Pipe And Exhaust Manifold Bolts
    GM654525Courtesy of GENERAL MOTORS COMPANY
  11. Remove the 3 bolts (1) retaining the right exhaust pipe to the exhaust manifold.
  12. Fig 5: View Of Exhaust Outlet Shield & Bolts
    GM668425Courtesy of GENERAL MOTORS COMPANY
  13. Remove the lower bolt (2) retaining the heat shield to the exhaust outlet.
  14. Lower the vehicle.
  15. Fig 6: Identifying Hood Hinge Normal And Service Position Bolt Holes
    GM310799Courtesy of GENERAL MOTORS COMPANY
  16. Move the hood to the service position by moving the hood hinge bolts (1) to the service positions (2).
  17. Fig 7: Upper Intake Manifold Sight Shield
    GM658266Courtesy of GENERAL MOTORS COMPANY
  18. Remove the upper intake manifold sight shield using the following procedure:
    1. Remove the retaining bolt in the front of the shield.
    2. Lift-up on the front of the shield.
    3. Lift the shield off the rear bracket.
  19. Fig 8: View Of Turbocharger Heat Shield & Bolt
    GM660382Courtesy of GENERAL MOTORS COMPANY
  20. Remove the 3 bolts holding the heat shield to the turbocharger.
  21. Remove the turbocharger heat shield.
  22. Fig 9: View Of Exhaust Outlet Shield & Bolts
    GM668425Courtesy of GENERAL MOTORS COMPANY
  23. Remove the remaining 2 bolts (1, 3) for the exhaust outlet heat shield.
  24. Remove the exhaust outlet heat shield.
  25. Fig 10: View Of Exhaust Outlet Nuts, Bolts & Gasket
    GM654540Courtesy of GENERAL MOTORS COMPANY
  26. Remove the exhaust outlet 4 bolts and the 2 nuts.
  27. Remove the exhaust outlet and gasket from the turbocharger.
  28. Position the exhaust outlet to the side in order to access the right exhaust pipe to turbocharger bolts.

    The exhaust outlet cannot be removed until the right exhaust pipe is removed.

  29. Fig 11: View Of Right Exhaust Pipe And Exhaust Manifold Bolts
    GM654525Courtesy of GENERAL MOTORS COMPANY
  30. Remove the 3 bolts (2) from the right exhaust pipe to the turbocharger.
  31. Remove the right exhaust pipe and gaskets.
  32. Remove the exhaust outlet out the bottom of the vehicle.
  33. Fig 12: View Of Exhaust Outlet Inspection Areas
    GM663765Courtesy of GENERAL MOTORS COMPANY
  34. Clean the exhaust outlet.
  35. Clean the exhaust outlet and turbocharger mating surfaces.
  36. Inspect the exhaust outlet for dents and cracks.
  37. Replace the exhaust outlet if any damage is found.