LEMON Manuals: Even more car manuals for everyone

Instrument Panel Upper Section: Removal

NOTE: Removal steps in this procedure may contain installation details.
  1. Remove the instrument panel. Refer to: Instrument Panel .
  2. Release the clips and remove the LH trim panel.

    • Disconnect the electrical connector.

    GFD653846Courtesy of FORD MOTOR COMPANY
  3. Release the clips and remove the trim panel.
    GFD653847Courtesy of FORD MOTOR COMPANY
  4. Remove the bolt and the display unit.

    • Disconnect the electrical connector.

      Torque: 22 lb.in (2.5 Nm)

    GFD653848Courtesy of FORD MOTOR COMPANY
  5. Remove the bolts, release the clips and remove the center instrument panel trim panel.

    • Disconnect the electrical connector.

      Torque: 22 lb.in (2.5 Nm)

    GFD653849Courtesy of FORD MOTOR COMPANY
  6. Remove the bolts and the center HVAC register.

    • Disconnect the electrical connector.

      Torque: 22 lb.in (2.5 Nm)

    GFD653850Courtesy of FORD MOTOR COMPANY
  7. Disconnect the electrical connector.
    GFD653851Courtesy of FORD MOTOR COMPANY
  8. Release the clips and remove the lower finish panel.
    GFD653852Courtesy of FORD MOTOR COMPANY
    1. Release the stop and fully lower the glove compartment.
    2. Remove the glove compartment check strap.
    GFD653853Courtesy of FORD MOTOR COMPANY
  9. Lift the glove compartment off the hinges remove.
    GFD653854Courtesy of FORD MOTOR COMPANY
  10. Remove the bolts, release the clips and remove the glove box close out.

    Torque: 36 lb.in (4.1 Nm)

    GFD653855Courtesy of FORD MOTOR COMPANY
  11. Remove the bolts, release the clips and remove the lower trim panel.

    • Disconnect the electrical connectors.

      Torque: 22 lb.in (2.5 Nm)

    GFD653856Courtesy of FORD MOTOR COMPANY
  12. Remove the steering column gap hider.
    GFD653857Courtesy of FORD MOTOR COMPANY
  13. Remove the bolts, release the clips and remove the IPC trim bezel.

    Torque: 33 lb.in (3.7 Nm)

    GFD653858Courtesy of FORD MOTOR COMPANY
  14. Remove the bolts, and the IPC.

    • Disconnect the electrical connector.

      Torque: 22 lb.in (2.5 Nm)

    GFD653859Courtesy of FORD MOTOR COMPANY
  15. Remove the bolts and the brace.

    Torque: 33 lb.in (3.7 Nm)

    GFD653860Courtesy of FORD MOTOR COMPANY
  16. Remove the instrument panel center speaker. Refer to: Instrument Panel Center Speaker .
  17. Release the clips and remove the HUD trim panel. Use the General Equipment: Interior Trim Remover
    GFD653861Courtesy of FORD MOTOR COMPANY
  18. Remove the bolts and the HUD.

    • Disconnect the electrical connector.

    GFD653862Courtesy of FORD MOTOR COMPANY
  19. Remove the bolt the RH register.

    Torque: 22 lb.in (2.5 Nm)

    GFD653863Courtesy of FORD MOTOR COMPANY
  20. Remove the bolts and the lower steering column trim panel.

    Torque: 17 lb.in (1.9 Nm)

    GFD653864Courtesy of FORD MOTOR COMPANY
  21. WARNING: Do not reuse steering column nuts. This may result in fastener failure and steering column detachment or loss of steering control. Failure to follow this instruction may result in serious injury to vehicle occupant(s).

    Remove the steering column.

    • Disconnect the electrical connector's.

    • Detach the harness pushpins.

    • Remove and discard the steering column nuts.

      Torque: 18 lb.ft (25 Nm)

    • Remove and discard the steering column bolt.

      Torque: 18 lb.ft (25 Nm)

    GFD653865Courtesy of FORD MOTOR COMPANY
  22. Disconnect the electrical connectors, release the harness retainers and position aside the harness.
    GFD653866Courtesy of FORD MOTOR COMPANY
  23. Remove the bolts and the ACM.

    Torque: 22 lb.in (2.5 Nm)

    GFD653867Courtesy of FORD MOTOR COMPANY
  24. Remove the screws and position the APIM down.

    Torque: 27 lb.in (3 Nm)

    GFD653868Courtesy of FORD MOTOR COMPANY
  25. Disconnect the electrical connectors and remove the APIM and bracket.
    GFD653869Courtesy of FORD MOTOR COMPANY
  26. Disconnect the electrical connectors and detach the harness pushpins.
    GFD653870Courtesy of FORD MOTOR COMPANY
  27. Remove the bolts.

    Torque: 22 lb.in (2.5 Nm)

    GFD653871Courtesy of FORD MOTOR COMPANY
  28. Remove the HVAC case bolts.

    Torque: 62 lb.in (7 Nm)

    GFD653872Courtesy of FORD MOTOR COMPANY
    1. Remove the bolts.

      Torque: 93 lb.in (10.5 Nm)

    2. Disconnect the electrical connector and detach the harness pushpin.
    GFD653873Courtesy of FORD MOTOR COMPANY
  29. Remove the front instrument panel upper section bolts.
    GFD653874Courtesy of FORD MOTOR COMPANY
    1. Disconnect the electrical connectors.
    2. Detach the harness retainers and position aside the electrical harness.
    3. Remove the rear instrument panel upper section bolts.
    GFD653875Courtesy of FORD MOTOR COMPANY
  30. NOTE: To avoid damaging the upper section, the aid of an assistant is required to carry out this step.
    NOTE: Make sure that all electrical connectors and wiring are not hindered before removing the upper section or damage to the components may occur.

    Remove the instrument panel upper section.

GFD653876Courtesy of FORD MOTOR COMPANY