LEMON Manuals: Even more car manuals for everyone

AUTOMTIC Transaxle/Transmission DTCS: 4R50E/4R75E

DTC CHART

DTC Component Description Condition Symptom Action
P0102
P0103
P1100
P1101
Mass Air Flow (MAF) MAF  concerns MAF  system has a malfunction which may cause a transmission concern. High or low Electronic Pressure Control (EPC) pressure, incorrect shift schedule. Incorrect Torque Converter Clutch (TCC) engagement scheduling. Symptoms similar to a Throttle Position (TP) failure. Refer to the INTRODUCTION .
P0112 Intake Air Temperature (IAT) IAT  indicates 125°C (257°F) (grounded) Voltage drop across IAT  exceeds scale set for temperature 125°C (257°F). Incorrect EPC  pressure, either high or low, results in harsh or soft shifts. Refer to the INTRODUCTION .
P0113 IAT  IAT  indicates - 40°C (-40°F) (open circuit) Voltage drop across IAT  exceeds scale set for temperature - 40°C (-40°F). Incorrect EPC  pressure, either high or low, results in harsh or soft shifts. Refer to the INTRODUCTION .
P0114 IAT  IAT  out of On-Board Diagnostic (OBD) range IAT  temperature higher or lower than expected during Key ON Engine OFF (KOEO) and Key ON Engine Running (KOER). Rerun OBD  test at normal operating temperature. Refer to the INTRODUCTION .
P0117 Engine Coolant Temperature (ECT) Engine Coolant Temperature (ECT) indicates 125°C (257°F) Voltage drop across Engine Coolant Temperature (ECT) exceeds scale set for temperature 125°C (257°F) (grounded). TCC  will always be off, resulting in reduced fuel economy. Refer to the INTRODUCTION .
P0118 Engine Coolant Temperature (ECT) Engine Coolant Temperature (ECT) indicates - 40°C (-40°F) Voltage drop across Engine Coolant Temperature (ECT) exceeds scale set for temperature -40°C (-40°F) (open circuit). TCC  will always be off, resulting in reduced fuel economy. Refer to the INTRODUCTION .
P0122
P0123
P1120
TP  TP  concern PCM has detected an error that may cause a transmission concern. Harsh engagements, firm shift feel, abnormal shift schedule, TCC  does not engage, TCC  cycling. Refer to the INTRODUCTION .
P0300-
P0308
P0320
P0340
P1351-
P1364
Electronic Ignition (EI) EI  system concerns EI  system has a malfunction which may cause a transmission concern. Harsh engagements and shifts, late Wide Open Throttle (WOT) shifts, no TCC  engagement. Refer to the INTRODUCTION .
P0500
P0503
P1502
ABS Insufficient Vehicle Speed Sensor (VSS) input from ABS through Standard Corporate Protocol (SCP) link PCM detected a loss of VSS  signal through SCP  link from ABS. No transmission symptom; Instrument Cluster (IC) speedometer may be affected. Refer to the INTRODUCTION .
P0705 Transmission Range (TR) TR  circuit failure TR  circuits, indicating an invalid pattern in TR  _D. Condition caused by a short to ground or an open in TR  4, TR  3, TR  2 and/or TR  circuits. This DTC cannot be set by an incorrectly adjusted TR  sensor. Increase in EPC  pressure (harsh shifts). Defaults to (D) or D for all gear positions. In (D) position trans, stuck in D or manual 2. Go to PINPOINT TEST C .
P0708 TR  TR  sensor circuit TR  3 open TR  sensor circuit TR  3 reading 2.6 V-5.0 V (open circuit). This DTC cannot be set by an incorrectly adjusted TR  sensor. Increase in EPC  pressure. Defaults to (D) or D for all gear ranges. Go to PINPOINT TEST C .
P0712 Transmission Fluid Temperature (TFT), wiring, PCM 157°C (315°F) indicated TFT  sensor circuit grounded Voltage drop across TFT  sensor exceeds scale set for temperature of 157°C (315°F). Firm shift feel. Go to PINPOINT TEST B .
P0713 TFT  , wiring, PCM -40°C (-40°F) indicated TFT  sensor circuit open Voltage drop across TFT  sensor exceeds scale set for temperature -40°C (-40°F). Firm shift feel. Go to PINPOINT TEST B .
P0715 Turbine Shaft Speed (TSS) Insufficient input from TSS  sensor PCM detected a loss of TSS  signal during operation. Harsh shifts, harsh TCC  activation and harsh engagements. Go to PINPOINT TEST F .
P0717 TSS  TSS  sensor signal intermittent PCM has detected an intermittent TSS  signal. Harsh shifts, harsh TCC  activation and harsh engagements. Go to PINPOINT TEST F .
P0718 TSS  TSS  sensor signal noisy PCM has detected a noisy TSS  signal. Harsh shifts, harsh TCC  activation and harsh engagements. Go to PINPOINT TEST F .
P0720 Output Shaft Speed (OSS) Insufficient input from OSS  sensor PCM detected a loss of OSS  signal during operation. Harsh shifts, abnormal shift schedule, no TCC  activation. Go to PINPOINT TEST E .
P0721 OSS  OSS  sensor signal noisy PCM has detected an erratic OSS  signal. Harsh shifts, abnormal shift schedule, no TCC  engagement. Go to PINPOINT TEST E .
P0722 OSS  wiring Insufficient input from OSS  PCM has detected a loss of OSS  signal. Harsh shifts, abnormal shift schedule, no TCC  engagement. Go to PINPOINT TEST E .
P0731 Shift Solenoid A (SSA), Shift Solenoid B (SSB) or internal parts 1st gear error No 1st gear. Incorrect gear selection, depending on failure or mode and manual lever position. Shift errors may also be due to other internal transmission concerns (stuck valves, damaged friction material). Engine rpm could be higher or lower than expected. Use the Solenoid Operation Chart, refer to PINPOINT TESTS - OSC EQUIPPED VEHICLE in this information. Go to PINPOINT TEST A .
P0732 SSA  , SSB  or internal parts 2nd gear error No 2nd gear. Incorrect gear selection, depending on failure or mode and manual lever position. Shift errors may also be due to other internal transmission concerns (stuck valves, damaged friction material). Engine rpm could be higher or lower than expected. Use the Solenoid Operation Chart, refer to PINPOINT TESTS - OSC EQUIPPED VEHICLE in this information. Go to PINPOINT TEST A .
P0733 SSA  , SSB  or internal parts 3rd gear error No 3rd gear. Incorrect gear selection, depending on failure or mode and manual lever position. Shift errors may also be due to other internal transmission concerns (stuck valves, damaged friction material). Engine rpm could be higher or lower than expected. Use the Solenoid Operation Chart, refer to PINPOINT TESTS - OSC EQUIPPED VEHICLE in this information. Go to PINPOINT TEST A .
P0734 SSA  , SSB  , or internal parts 4th gear error No 4th gear. Incorrect gear selection, depending on failure or mode and manual lever position. Shift errors may also be due to other internal transmission concerns (stuck valves, damaged friction material). Engine rpm could be higher or lower than expected. Use the Solenoid Operation Chart, refer to PINPOINT TESTS - OSC EQUIPPED VEHICLE in this information. Go to PINPOINT TEST A .
P0740 TCC  , wiring, PCM TCC  electrical failure TCC  circuit fails to provide voltage drop across solenoid. Circuit open, shorted or PCM driver failure during OBD  test. Short circuit, engine stalls in 2nd ((D), manual 2 range) at low speeds with brake applied. Open circuit, TCC  never engages. May flash Transmission Control Indicator Lamp (TCIL). Go to PINPOINT TEST A .
P0741 TCC  , internal components TCC  slippage detected The PCM picked up an excessive amount of slippage during normal vehicle operation. TCC  slippage/erratic or no TCC  operation. Flashing TCIL  . Refer to DIAGNOSIS BY SYMPTOM in this information.
P0743 TCC  , wiring, PCM TCC  solenoid circuit failure during OBD  test TCC  solenoid circuit fails to provide voltage drop across solenoid. Circuit open or shorted or PCM driver failure during OBD  test. Short circuit: engine stalls in second ((D), 2 range) at low idle speeds with brake applied.
Open circuit: TCC  never engages. May flash TCIL  .
Go to PINPOINT TEST A .
P0748 EPC  solenoid EPC  solenoid circuit failure Voltage through EPC  solenoid is checked. An error will be noted if tolerance is exceeded. Short circuit results in minimum EPC  pressure (minimum capacity) and limits engine torque (alternate firm). Not all gears present.
Open circuit: maximum Pressure Control Solenoid A (PCA) pressure, harsh engagements and shifts.
Go to PINPOINT TEST D .
P0750 SSA  , wiring, PCM SSA  solenoid circuit failure SSA  circuit failed to provide voltage drop across solenoid. Circuit open or shorted or PCM driver failure during OBD  test. Incorrect gear selection depending on condition mode and manual lever position. See the appropriate Solenoid Operational Chart. Go to PINPOINT TEST A .
P0753 SSA  , wiring, PCM SSA  electrical failure SSA  circuit fails to provide voltage drop across solenoid. Circuit open or shorted or PCM driver failure during OBD  test. Incorrect gear depending on condition mode and manual lever position. See the appropriate Solenoid Operational Chart. May flash TCIL  . Go to PINPOINT TEST A .
P0755 SSB  , wiring, PCM SSB  solenoid circuit failure SSB  circuit fails to provide voltage drop across solenoid. Circuit open or shorted or PCM driver failure during OBD  test. Incorrect gear selection depending on condition mode and manual lever position. See the appropriate Solenoid Operation Chart. Go to PINPOINT TEST A .
P0758 SSB  , wiring, PCM SSB  electrical circuit failure SSB  circuit fails to provide voltage drop across solenoid. Circuit open or shorted or PCM driver failure during OBD  test. Incorrect gear depending on condition mode and manual lever position. See the appropriate Solenoid Operation Chart. May flash TCIL  . Go to PINPOINT TEST A .
P0781 SSA  or internal parts 1-2 shift error Engine rpm drop not detected when 1-2 shift was commanded by PCM. Incorrect gear selection depending on failure or mode and manual lever position. Shift errors may also be due to other internal transmission concerns (stuck valves, damaged friction material). Refer to SOLENOID OPERATION CHART , then Go to PINPOINT TEST A .
P0782 SSA  , SSB  or internal parts 2-3 shift error Engine rpm drop not detected when 2-3 shift was commanded by PCM. Incorrect gear selection depending on failure or mode and manual lever position. Shift errors may also be due to other internal transmission concerns (stuck valves, damaged friction material). Refer to SOLENOID OPERATION CHART , then Go to PINPOINT TEST A .
P0783 SSA  , SSB  or internal parts 3-4 shift error Engine rpm drop not detected when 3-4 shift was commanded by PCM. Incorrect gear selection depending on failure or mode and manual lever position. Shift errors may also be due to other internal transmission concerns (stuck valves, damaged friction material). Refer to SOLENOID OPERATION CHART , then Go to PINPOINT TEST A .
P0963 EPC  solenoid EPC  solenoid short to power circuit failure Voltage through EPC  solenoid is checked. An error will be noted if tolerance is exceeded. Maximum EPC  pressure, harsh engagements and shifts. Go to PINPOINT TEST D .
P1116 ECT  ECT  out of OBD  range ECT  temperature higher or lower than expected during KOEO  and KOER  . Rerun OBD  test at normal operating temperature. Refer to the INTRODUCTION .
P1124 TP  TP  voltage high/low for OBD test TP  was not in the correct position for OBD  test. Rerun OBD  at appropriate TP  per application. Refer to the INTRODUCTION .
P1460 A/C A/C clutch cycling pressure switch error A/C or defrost on condition may result from A/C clutch being on during OBD  test. DTC set during OBD  test, repeat with A/C off. Failed on, EPC  pressure slightly low with A/C off. Refer to the INTRODUCTION .
P1636 PCM PCM detected internal error - - Refer to the INTRODUCTION .
P1702 TR  Intermittent DTC P0705 or P0708 Refer to DTC P0705 or P0708 in DTC CHART . Refer to DTC P0705 or P0708 in DTC CHART . Go to PINPOINT TEST C .
P1703 Brake Pedal Position (BPP) BPP  switch circuit failed Brake ON/OFF circuit failure. Failed on or not connected - TCC  will not engage at less than one-third throttle. Failed off or not connected - TCC  will not disengage when brake is applied. Refer to the INTRODUCTION .
P1703 BPP  Brake not actuated during OBD  test Brake not cycled during KOER  . Failed off or not connected - TCC  will not engage at less than one-third throttle. Failed off or not connected - TCC  will not disengage when brake is applied. Refer to the INTRODUCTION .
P1704 TR  TR  circuit reading in between gear position during KOEO  and KOER  TR  sensor or selector lever cable incorrectly adjusted; or TR  circuit failure. Wrong commanded EPC  pressure. TR  reading the wrong gear position. Go to PINPOINT TEST C .
P1705 TR  TR OBD  test was not carried out in PARK or NEUTRAL Vehicle not in PARK or NEUTRAL during OBD  test. Rerun OBD  test in PARK or NEUTRAL. Go to PINPOINT TEST C .
P1711 TFT  TFT  out of OBD  test range Transmission not at operating temperature during OBD  test. Warm vehicle to normal operating temperature. Go to PINPOINT TEST B .
P1713 TFT  wiring PCM TFT  continually reading cold TFT  sensor in range low failure. Firm shift feel. Substitute ECT  for TFT  . Go to PINPOINT TEST B .
P1714 SSA  , internal components SSA  malfunction Mechanical failure of the solenoid detected. Incorrect gear selection depending on condition, mode and manual lever position. See SOLENOID OPERATION CHART . Go to PINPOINT TEST G .
P1715 SSB  SSB  malfunction Mechanical failure of the solenoid detected. Incorrect gear selection depending on condition, mode and manual lever position. See SOLENOID OPERATION CHART . Go to PINPOINT TEST G .
P1718 TFT  , wiring, PCM TFT  continually reading hot TFT  sensor in range high failure. Firm shift feel. Substitute ECT  for TFT  . Go to PINPOINT TEST B .
P1728 Transmission Transmission slip error The PCM has detected an excessive amount of slippage during normal operation. Transmission slippage erratic or no TCC  operation. Refer to DIAGNOSIS BY SYMPTOM in this information.
P1740 TCC  TCC  malfunction Mechanical failure of the solenoid detected. Failed on - engine stalls in 2nd ((D), Manual 2 ranges) at low idle speeds with brake applied. Failed off - TCC  never applies. Go to PINPOINT TEST G .
P1741 TCC  , internal components Excessive TCC  engagement error Excessive variations in slip (engine speed surge) across the TCC  . Engine rpm oscillation is present in 3rd gear. Go to PINPOINT TEST A .
P1742 TCC  , internal components TCC  solenoid failed on TCC  solenoid has failed on by electric, mechanical or hydraulic concern. Harsh shifts. Go to PINPOINT TEST A .
P1743 TCC  , internal components TCC  solenoid failed on TCC  solenoid has failed on by electric, mechanical or hydraulic concern. Harsh shifts. Go to PINPOINT TEST A .
P1744 TCC  TCC  The PCM picked up an excessive amount of TCC  slippage during normal vehicle operation. TCC  slippage/erratic or no TCC  operation. Refer to DIAGNOSIS BY SYMPTOM in this information.
P1746
P0960
EPC  , wiring, PCM EPC  solenoid open circuit Voltage through EPC  solenoid is checked. An error will be noted if tolerance is exceeded. Open circuit causes maximum EPC  pressure, harsh engagements and shifts. Go to PINPOINT TEST D .
P1747
P0962
EPC  , wiring, PCM EPC  solenoid circuit failure, shorted circuit or output driver Voltage through EPC  solenoid is checked. An error will be noted if tolerance is exceeded. Short circuit causes minimum EPC  pressure (minimum capacity) and limits engine torque (alternate firm). Go to PINPOINT TEST D .
P1760 EPC  , wiring, PCM EPC  solenoid circuit failure, shorted circuit or output driver PCM detected a loss of EPC  during operation. Unexpected reduction in engine torque. Go to PINPOINT TEST D .
P1780 TCS  TCS  not changing states TCS  not cycled during OBD  test. TCS  circuit open or shorted. Rerun OBD  test and cycle switch. No O/D  cancel when TCS  is cycled. Refer to the INTRODUCTION .
P1783 TFT  Transmission over temperature condition indicated TFT  exceeded 135°C (275°F). - Go to PINPOINT TEST B .
U1039 PCM Data communication link error Insufficient VSS  input to IC  via SCP  link. No VSS  input to IC  . Refer to the INTRODUCTION .
- TCIL  TCIL  circuit failure TCIL  circuit open or shorted. Failed on, O/D  cancel mode on. No flashing TCIL  for EPC  failure or sensor. Failed off, O/D  cancel mode never indicated. No flashing TCIL  for EPC  sensor failure. Refer to the INTRODUCTION .