Diagnostic Aids
Perform this test only when instructed by QUICK TEST or if directed by other test procedure. This test is intended to diagnose the following:
- HO2S sensor.
- HO2S connections.
- Vacuum systems.
- Fuel injector and/or fuel injector circuitry.
- Powertrain Control Module (PCM).
- Harness circuits: HO2S, HO2SH, INJ 1-4 and VPWR.
To prevent replacement of good components, be aware the following non-EEC areas may be cause of driveability concerns:
- Ignition system.
- Faulty evaporative emission system.
- EGR and/or PCV system.
- Air intake system.
- Engine oil contamination.
- Fuel system.
- Exhaust system leaks or restriction.
| Circuit | Breakout Box Pin No. | PCM Pin | Wire Color |
|---|---|---|---|
| HO2S12 | 26 | C2-10 | Orange/White |
| O2S11 | 78 | C2-2 | White |
| SIG RTN | 49 | C2-8 | Yellow/Green |
| INJ1 | 68 | C3-11 | Green/Yellow |
| INJ2 | 69 | C3-24 | Green/Black |
| INJ3 | 70 | C3-12 | Green/Red |
| INJ4 | 71 | C3-25 | Green/Black |
| VPWR | 51 | C3-14 | Yellow/White |
- 1) DTC P0130
This trouble code indicates an irrational value in upstream O2S circuit. Possible causes for fault are as follows:
- Damaged upstream O2S.
- Fault in intake air system.
- Fuel system malfunction.
- Ignition system malfunction
Turn ignition off. Connect NGS scan tool to OBD-II DLC. Start engine and run until engine is at normal operating temperature. Access O2S PID. Run engine at different speeds while observing O2S PID. If O2S PID is not constantly varying between 0.4-1.0 volt, go to step 40). If O2S PID is 0.4-1.0 volt and constantly varying, O2S is okay at this time. Go to CIRCUIT TEST Z or TESTS W/O CODES article for intermittent diagnostic procedure.
NOTE: A break in step numbering sequence occurs at this point. Procedure skips from step 1) to step 10). No test procedures have been omitted. - 10) DTC P0134 & DTC P1170
DTC P0134 indicates that upstream O2S signal does not exceed 0.5 volt for more than 2 minutes with engine running at more than 1500 RPM. DTC P1170 indicates upstream O2S signal remains unchanged for 20 seconds after closed loop operation began. Possible causes for fault are as follows:
- Faulty or damaged O2S.
- Poor harness connections.
If harness connections are okay and no apparent damage to O2S exists, go to next step. If connection is faulty or O2S damage is apparent, replace or repair as necessary.
- 11) Check O2S Output Voltage Warm engine to normal operating temperature. Turn ignition off. Connect NGS scan tool to OBD-II DLC. Access O2S PID. Start engine and run at 2000 RPM while observing O2S PID. If O2S reaches 0.5 volt or greater, go to step 14). If O2S never reaches 0.5 volt or greater, go to next step.
- 12) Check O2S Circuit Continuity Turn ignition off. Disconnect upstream O2S connector. Disconnect PCM connector. Inspect connector for damaged pins and repair if necessary. Install breakout box (leave PCM disconnected). Measure resistance between suspect O2S harness connector and O2S11 test pin at breakout box. See Fig 1. If resistance is less than 5 ohms, go to next step. If resistance is greater than 5 ohms, repair open O2S circuit. Repeat QUICK TEST .
- 13) Check O2S Signal Short To Ground Measure resistance between breakout box test pin O2S11 and ground. If resistance is less than 10 k/ohms repair short to ground in O2S circuit. Repeat QUICK TEST. If resistance is greater than 10 k/ohms, go to step 40). If all systems are okay, go to step 15).
- 14) Check For Short To Power Turn ignition off. Disconnect upstream O2S sensor. Install breakout box (leave PCM disconnected). Turn ignition on. Measure voltage between breakout box test pin O2S11 and ground. If one volt or more is present, repair short to power in O2S circuit. If less than one volt is present, go to step 40). If all systems are okay, go to step 15).
- 15) Erase DTCs
Erase DTCs from memory. See CLEARING CODES. Run engine at 1500-2000 RPM for at least 3 minutes. Repeat QUICK TEST. If DTC P0134 or P1170 does not return, fault may be intermittent. Go to CIRCUIT TEST Z or TESTS W/O CODES
article. If DTC P0134 or P1170 return, replace O2S. If either DTC is still present, replace PCM.NOTE: A break in step numbering sequence occurs at this point. Procedure skips from step 15) to step 30). No test procedures have been omitted.
- 30) DTC P0140
This trouble code indicates that downstream HO2S signal does not exceed 0.5 volt for more than 2 minutes with engine running at more than 1500 RPM. Possible causes for fault are as follows:
- Faulty or damaged HO2S.
- Poor harness connections.
If harness connections are okay and no apparent damage to HO2S exists, go to next step. If connection is faulty or HO2S damage is apparent, replace or repair as necessary.
- 31) Check HO2S Output Voltage Warm engine to normal operating temperature. Turn ignition off. Connect NGS scan tool to OBD-II DLC. Access HO2S PID. Start engine and run at 2000 RPM while observing HO2S PID. If HO2S reaches 0.5 volt or greater, go to step 37). If HO2S never reaches 0.5 volt or greater, go to next step.
- 32) Check VPWR Circuit Continuity Turn ignition off. Disconnect downstream HO2S sensor. Turn ignition on. Measure voltage between VPWR terminal at HO2S harness connector and ground. If voltage is greater than 10.5 volts, go to next step. If voltage is less than 10.5 volts, repair open VPWR circuit. Repeat QUICK TEST .
- 33) Check Heater Ground Circuit Continuity Turn ignition off. Measure resistance between HTR GND terminal at harness connector and chassis ground. If resistance is less than 5 ohms, go to next step. If resistance is greater than 5 ohms, repair open heater ground circuit. Restore electrical connections repeat QUICK TEST.
- 34) Check HO2S Heater Measure resistance between VPWR terminal and HTR GND terminal (component side). If resistance is approximately 6 ohms, go to next step. If resistance is not approximately 6 ohms, replace HO2S. Restore electrical connections and repeat QUICK TEST.
- 35) Check HO2S Circuit Continuity Disconnect PCM connector. Inspect connector for damaged pins and repair if necessary. Install breakout box (leave PCM disconnected). Measure resistance of HO2S circuit between HO2S harness connector and breakout box test pin HO2S12. If resistance is less than 5 ohms, go to next step. If resistance is greater than 5 ohms, repair open HO2S circuit. Repeat QUICK TEST.
- 36) Check HO2S Signal Short To Ground Measure resistance between breakout box test pins HO2S12 and GND, and test pins HO2S12 and SIG RTN. If resistance is less than 10 k/ohms, repair short to ground in HO2S circuit. Repeat QUICK TEST . If resistance is greater than 10 k/ohms, go to next step.
- 37) Check For Short To Power Measure resistance between breakout box test pins HO2S12 and VPWR, and test pins HO2S12 and VREF. If resistance is greater than 10 k/ohms, go to next step. If resistance is less than 10 k/ohms, repair short to power in HO2S circuit. Restore electrical connections and repeat QUICK TEST.
- 38) Erase DTCs
Erase DTCs from memory See CLEARING CODES. Run engine at 1500-2000 RPM for at least 3 minutes. Repeat QUICK TEST. If DTC P0140 returns, replace HO2S.NOTE: A break in step numbering sequence occurs at this point. Procedure skips from step 38) to step 40). No test procedures have been omitted.
- 40) DTC P0170
This trouble code indicates air/fuel ratio too lean or rich. Possible causes for fault are as follows:
- Excessive fuel pressure.
- Leaking fuel injector.
- Leaking fuel pressure regulator.
- Low fuel pressure.
- Restricted fuel injectors.
- Faulty O2S or circuit.
- Induction system air leaks.
- Restricted air filter.
- Faulty PCV system.
- Engine mechanical problem.
- Ignition system malfunction.
If any of the above areas are faulty, repair as necessary. If all of the above areas are okay, go to next step.
- 41) Fuel Pressure Check Connect fuel pressure gauge to fuel rail or fuel filter. Locate diagnostic connector next to battery. Jump FP terminal in diagnostic connector to ground. See Fig 2. Turn ignition on and observe fuel pressure. For fuel pressure specifications, see FUEL PRESSURE SPECIFICATIONS article. If fuel pressure is within specification, go to next step. If fuel pressure is not within specification, go to CIRCUIT TEST HC.
- 42) Check Fuel Pressure Leak-Down
With fuel pressure gauge installed, turn ignition switch on and off several times. Turn ignition off and observe fuel pressure gauge. If fuel pressure drops less than 5 psi in one minute, go to step 44). If fuel pressure drops 5 psi or more in one minute, check for external leaks. If no external leakage is found, check fuel injectors, fuel pressure regulator and fuel pump check valve for internal leakage. See CIRCUIT TEST HC.NOTE: A break in step numbering sequence occurs at this point. Procedure skips from step 42) to step 44). No test procedures have been omitted.
- 44) Check Injector Circuit Resistance
Turn ignition off. Disconnect PCM and inspect connector for corroded or pushed out pins etc. Repair as necessary. Install breakout box (leave PCM disconnected). Measure resistance between breakout box test pin No. 51 (VPWR) and fuel injector test pins. See FUEL INJECTOR TEST PINS table. See Fig 3. If resistance is 12-16 ohms, circuit is okay, go to step 47). If resistance is not 12-16 ohms, go to step 45).FUEL INJECTOR TEST PINS
Cyl. No. Pin No. 1 68 2 69 3 70 4 71 - 45) Check Injector Harness Disconnect injector harness connectors. With breakout box installed and PCM disconnected, measure resistance between breakout box test pin VPWR and VPWR terminal at each injector harness connector. Measure resistance between injector signal terminal at injector harness and appropriate breakout box test pin. See FUEL INJECTOR TEST PINS table. If resistance is less than 5 ohms, go to next step. If resistance is greater than 5 ohms, repair open harness circuit as necessary. Restore electrical connections and repeat QUICK TEST.
- 46) Check Injector Harness For Short To Power Or Ground Measure resistance between breakout box test pins VPWR, GND and SIG RTN. Measure resistance between injector test pin at breakout box and chassis ground. See FUEL INJECTOR TEST PINS table. If all resistance measurements are 10 k/ohms or greater, go to next step. If any resistance measurement is less than 10 k/ohms, repair shorted harness circuit as necessary. Restore electrical connections and repeat QUICK TEST.
- 47) Check Injector Driver Connect PCM to breakout box. Connect a standard non-powered test light between breakout box test pin VPWR and each injector test pin. See FUEL INJECTOR TEST PINS table. Crank engine. If test light dimly glows while cranking, remove breakout box and reconnect PCM. Go to next step. If test light does not glow or glows brightly, replace PCM. Restore electrical connections and repeat QUICK TEST .
- 48) Check Injector Flow Using Rotunda Fuel Injector Tester Cleaner (164-R3750), flow test injectors according to tester instructions. Replace any injector that is not within leakage and flow specification. If all injectors are within leakage and flow specifications, fault is intermittent. See CIRCUIT TEST Z or TESTS W/O CODES article.