LEMON Manuals: Even more car manuals for everyone

Diagnostic Aids

Perform this test only when directed by QUICK TEST. This test is intended to diagnose only the following circuits or systems:

4.0L SPFI-MA TEST PIN WIRE COLOR I.D.

Pin No. Ckt. No. (Ckt. Title) Wire Color
Pin 30
A/T 199 (NDS) Light Blue/Yellow
M/T 199 (CIS) Light Blue/Yellow
Pin 40 60 (PWR GND) Black/Light Green
Pin 46 359 (SIG RTN) Gray/Red
Pin 48 100 (STI) White/Red
Pin 60 60 (PWR GND) Black/Light Green
4.0L SPFI-MA TEST PIN WIRE COLOR I.D. (RANGER & EXPLORER, NAVAJO)

Pin No. Ckt. No. (Ckt. Title) Wire Color
Pin 30
A/T 199 (NDS) Light Blue/Yellow
M/T 199 (CIS) Light Blue/Yellow
Pin 40 570 (PWR GND) Black/Light Green
Pin 46 359 (SIG RTN) Gray/Red
Pin 48 209 (STI) White/Purple
Pin 60 570 (PWR GND) Black/Light Green

1) Code 67/522, 525, 527, 528 Or 634 System Identification  Code 67/522, 525, 527, 528 Or 634 is a result of voltage being high at either pin No. 10 (A/C input) or pin No. 30 (neutral drive) while cranking engine or during KOEO SELF-TEST. Possible causes for these faults are as follows:

Fig 1: Neutral Gear/Clutch Input Circuit
G91G09230
Fig 2: Checking Clutch Engage Switch
G91I09231
NOTE: There is a break in the step numbering sequence at this point, skipping from step 1) to step 8). Break is due to previous chart references to these testing procedures. No test procedures have been omitted.

8) Check Neutral Drive Input  Turn ignition off and wait 10 seconds. Ensure heater control is in OFF position (if equipped). Ensure transmission is in NEUTRAL or PARK position. Disconnect ECA 60-pin connector. Inspect connector for damaged pins, corrosion, or loose wires; repair as necessary. Install breakout box and connect ECA to breakout box. Set DVOM to 20-volt scale. With KOEO, measure voltage between test pin No. 30 and chassis ground. If voltage is less than one volt, go to TEST KM, step 40) (vehicles with A/C), or replace ECA, remove breakout box and rerun QUICK TEST (all others). If voltage is greater than one volt, go to next step.

Fig 3: Checking Neutral Drive Switch
G91A09232

9) Check Neutral Drive Switch  Turn ignition off and wait 10 seconds. Install breakout box, leaving ECA disconnected. Set DVOM to 200-ohm scale. Disconnect vehicle harness from neutral drive switch and measure resistance across switch. If resistance is less than 5 ohms, repair open circuit in vehicle harness Neutral Drive circuit. Remove breakout box, reconnect all components and rerun QUICK TEST. If resistance is greater than 5 ohms, replace neutral drive switch. Remove breakout box, reconnect all components and rerun QUICK TEST.

10) Check Neutral Drive Input  Turn ignition off and wait 10 seconds. Ensure transmission is in NEUTRAL or PARK position. Disconnect ECA 60-pin connector. Inspect connector for damaged pins, corrosion, or loose wires; repair as necessary. Install breakout box and connect ECA to breakout box. Set DVOM to 20-volt scale. Disconnect 4EAT module 16-pin connector. With KOEO, measure voltage between test pin No. 30 and chassis ground. If voltage is less than one volt, replace ECA. Remove breakout box, reconnect all components and rerun QUICK TEST. If voltage is greater than one volt, go to next step.

Fig 4: Checking Neutral Drive Input
G91C09233

11) Check NDS Circuit Continuity Between ECA And 4EAT Module  Turn ignition off and wait 10 seconds. Install breakout box and leave ECA disconnected. Disconnect 4EAT 16-pin connector. Set DVOM to 200-ohm scale. Measure resistance between test pin No. 30 and NDS pin at 4EAT module vehicle harness connector. If resistance is less than 5 ohms, diagnose 4EAT system; remove breakout box, reconnect all components and rerun QUICK TEST. If resistance is greater than 5 ohms, repair open circuit; remove breakout box, reconnect all components and rerun QUICK TEST.

Fig 5: Checking NDS Continuity
G91E09234

12) Check NDS Circuit For Short To Ground Or Closed Neutral Drive Switch  Turn ignition off and wait 10 seconds. Disconnect ECA 60-pin connector. Inspect connector for damaged pins, corrosion, or loose wires; repair as necessary. Install breakout box and leave ECA disconnected. Set DVOM to 200-k/ohm scale. Place transmission in DRIVE position. Measure resistance between test pins No. 30 and 40/60. If resistance is greater than 10 k/ohms, NDS circuit okay. Diagnose other possible causes. If resistance is less than 10 k/ohms, repair closed neutral drive switch or short circuit. Remove breakout box, reconnect all components and rerun QUICK TEST.