Anti-Theft VIN Identification Labels (88-7-2)
Publication date: 1988-07-20Reference number: 88-7-2
Supersedes refnos: 88-15-4
ANTI-THEFT VIN IDENTIFICATION LABELS
TECHNICAL SERVICE BULLETIN
Superceded Bulletin(s): 88-7-2, Date of Issue: March 30, 1988
CONDITIONS
SHEET METAL - THEFT PREVENTION STANDARD - PARTS IDENTIFICATION NUMBER
ENGINE - THEFT PREVENTION STANDARD - PARTS IDENTIFICATION NUMBER
TRANSMISSION - THEFT PREVENTION STANDARD - PARTS IDENTIFICATION NUMBER
APPLICATION
Model(s): FORD: 1989 PROBE, MUSTANG, THUNDERBIRD
LINCOLN-MERCURY: 1989 COUGAR, MARK VII, CONTINENTAL, LINCOLN TOWN CAR
MERKUR: 1989 XR4Ti, SCORPIO
Date: July 20, 1988
Bulletin No: 88-15-4
SERVICE INFORMATION
This bulletin supersedes service bulletin 88-7-2 dated March 30, 1988.
ISSUE
The U.S. Motor Vehicle Theft Law Enforcement Act of 1984 requires identification of certain high theft vehicles to reduce the National Auto Theft Rate. This federal law requires Ford Motor Company to affix the vehicle identification number (VIN) on specific parts. These "body parts" are the bumpers, fenders, hood, front and rear doors, quarter panels and luggage compartment door. The other affected components are engines and transmissions. In addition, the service replacement parts must also be identified as "service" parts.
The production car parts are identified by an adhesive-backed white label on which the vehicle "VIN" number is printed. The appropriate service parts are identified by a similar label on which is printed a letter "R", an oval "FORD" logo and the letters "D.O.T." (Department of Transportation). The "production" label is about 2-3/16" long and 5/8" wide, white in color with a small blue Ford logo printed on it. The "service" label is also white and is about 2-3/4" long and 5/8" wide with gray lettering.
The labels, both "production" and "service", are purposely made very fragile. Any attempt to remove, alter, obliterate or tamper with the label will be very evident. Consequently, if repairs are made in the vicinity of a label, the label must be protected. Any sort of adhesive covering material, (masking tape, etc.) placed directly on the label will cause damage, therefore, it is suggested that a double thickness of heavy paper (grocery bag, etc.) be cut to cover the label. This protective cover can then be held in place with masking tape. An alternate protective covering is reusable magnetic tape available from 3M distributors (part number 80-000-0329-S). If paint is involved, the area around the label that was covered by the masking tape or magnetic tape can then be "touched up" with a brush when the label protection is removed.
The replacement part (service) label comes with a protective mask. As the new service part requires painting, undercoating or rustproofing, the label cover should be left on until all repairs are completed .
ACTION
In the event of collision damage not requiring part replacement or drivetrain service, the persons making the repairs should take care not to damage or remove the labels, unless such ACTION is reasonably necessary in performing the repair.
The areas selected for the location of the "production" and "service" labels are unlikely to be affected during normal servicing and non-collision repairs.
The following information indicates federal penalties for violations of the theft prevention standard.
FEDERAL CIVIL PENALTY
Violators of these requirements may be subject to a civil penalty of up to $1,000 per violation by NHTSA.
FEDERAL CRIMINAL LAW
Federal criminal law provides that whoever knowingly removes, obliterates, tampers with or alters an identification number for a motor vehicle or motor vehicle part shall be fined not more than S10,000 or imprisoned not more than five (5) years, or both. This provision does not apply to the removal, obliteration, tampering or alteration by a person who repairs such a vehicle or part, if the removal, obliteration, tampering or alteration is reasonably necessary for the repair, unless that person knows that the vehicle or part involved is stolen (United States Code, Title 18, Section 511 ).