LEMON Manuals: Even more car manuals for everyone

Flash: Powertrain Control Module (Pcm) Updates (18-032-19)

Publication date: 2019-03-14
Reference number: 18-032-19
Supersedes refnos: 18-027-17

FLASH: POWERTRAIN CONTROL MODULE (PCM) UPDATES

FLASH: POWERTRAIN CONTROL MODULE (PCM) UPDATES

TECHNICAL SERVICE BULLETIN

Reference Number(s): 18-032-19, Date of Issue:  March 14, 2019
CHRYSLER: 2017 Dodge Challenger (LA), Dodge Charger (LD), Chrysler 300 (LX)
GROUP: 18 - Vehicle Performance
Superceded Bulletin(s): 18-027-17, Date of Issue:  March 07, 2017
NOTE: THIS BULLETIN SUPERSEDES SERVICE BULLETIN 18-027-17, DATED MARCH 07, 2017, WHICH SHOULD BE REMOVED FROM YOUR FILES. ALL REVISIONS ARE HIGHLIGHTED WITH **ASTERISKS** AND INCLUDES ADDITIONAL SYMPTOM/CONDITION FOR LD VEHICLES WITH (SALES CODES ERB WITH AHB OR AHV) AND LOP.

OVERVIEW

This bulletin involves reprogramming the PCM with the latest available software.

MODELS

MODELS CHART

2017 (LA) Dodge Challenger
2017 (LD) Dodge Charger
2017 (LX) Chrysler 300
NOTE: This bulletin applies to vehicles within the following markets/countries: NAFTA, APAC, EMEA and LATAM.
NOTE: This bulletin applies to vehicles equipped with 3.6L V6 24V VVT Engine (Sales Code ERB) or 3.0L V6 24V VVT Engine (Sales Code EHD) and 8-SPD Auto 845RE Transmission (Sales Code DFL) or 5-Speed Auto W5A580 Transmission (Sales Code DGJ).

SYMPTOM/CONDITION

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) set in the PCM memory:

In addition to the above DTC, this software release also includes:

DIAGNOSIS

Using a Scan Tool (wiTECH) with the appropriate Diagnostic Procedures available in DealerCONNECT/Service Library, verify all related systems are functioning as designed. If DTCs or symptom conditions, other than the ones listed above are present, record the issues on the repair order and repair as necessary before proceeding further with this bulletin.

If the customer describes the symptom/condition listed above or if the technician finds the DTC, perform the Repair Procedure.

REPAIR PROCEDURE

NOTE: The Transmission Control Module (TCM) must be updated to the latest available software at the conclusion of this repair procedure. Refer to all applicable published service bulletins for detailed repair procedures and labor times regarding updating the TCM software.
NOTE: Install a battery charger to ensure battery voltage does not drop below 13.2 volts. Do not allow the charging voltage to climb above 13.5 volts during the flash process.
NOTE: If this flash process is interrupted/aborted, the flash should be restarted.
  1. Reprogram the PCM with the latest software. Detailed instructions for flashing control modules using the wiTECH Diagnostic Application are available by selecting the application's "HELP" tab.
  2. Clear any DTCs that may have been set in any modules due to reprogramming. The wiTECH application will automatically present all DTCs after the flash and allow them to be cleared.
  3. Verify the TCM is programmed with the latest available software. Refer to all applicable published service bulletins for detailed repair procedures and labor times regarding updating the TCM software.

POLICY

Reimbursable within the provisions of the warranty.

TIME ALLOWANCE

TIME ALLOWANCE CHART

Labor Operation No: Description Skill Category Amount
**18-19-06-YV Module, Powertrain Control (PCM) - Reprogram
(0 - Introduction)
1 - Engine Repair and Performance 0.2 Hrs.**
NOTE: The expected completion time for the flash download portion of this procedure is approximately 5 minutes. Actual flash download times may be affected by vehicle connection and network capabilities.

FAILURE CODE

The dealer must use failure code CC with this Service Bulletin. 

FAILURE CODE CHART

CC Customer Concern