LEMON Manuals: Even more car manuals for everyone

Removal And Installation: Installation

CAUTION:

The Thermostat and housing is serviced as an assembly. Do not remove the thermostat from the housing, damage to the thermostat may occur.

Fig 1: Thermostat Housing Gasket
GC0163135Courtesy of CHRYSLER GROUP, LLC
  1. Clean the mating surfaces on the engine block and thermostat housing.
  2. Install a new thermostat housing gasket (1).
    Fig 2: Thermostat Housing, Engine Coolant Temperature Sensor & Bolts
    GC0171104Courtesy of CHRYSLER GROUP, LLC
  3. Pull the intake manifold upper support bracket slightly away from the engine and install the thermostat housing (1) with two bolts (2) hand tight.
  4. If removed, install the Engine Coolant Temperature (ECT) sensor (3) to the thermostat housing (1) and tighten to the proper specification. Refer to SPECIFICATIONS .
    Fig 3: Loop Clamp & Bolt
    GC0171106Courtesy of CHRYSLER GROUP, LLC
  5. Position the loop clamp (1) and install the thermostat housing bolt (2) hand tight.
    Fig 4: Intake Manifold Upper Support Bracket, Bolts, Nuts, Hose & Connector
    GC0171601Courtesy of CHRYSLER GROUP, LLC
  6. Install the two bolts (2) to the intake manifold upper support bracket (1) hand tight.
  7. Tighten the intake manifold upper support bracket nuts (3) to the proper specification. Refer to TORQUE SPECIFICATIONS .
  8. Tighten the intake manifold upper support bracket bolts (2) and the three other previously installed thermostat housing bolts in a criss-cross pattern to the proper specification. Refer to TORQUE SPECIFICATIONS .
  9. Connect and lock the Engine Coolant Temperature (ECT) sensor harness connector (4).
  10. Install the degas hose (5) to the thermostat housing and connect the quick-connect fitting.
    Fig 5: Coolant Tube To Thermostat Housing Lock Tab & Bolt
    GC0165638Courtesy of CHRYSLER GROUP, LLC
  11. Bend the loop clamp end tab (1a) to secure the thermostat housing bolt (1b).
    Fig 6: Heater Hoses
    GC0172072Courtesy of CHRYSLER GROUP, LLC
  12. Install the heater core outlet hose (2) to the coolant return pipe with the CLIC E®  type clamp using (special tool #10288, Pliers, Hose Clamp).
  13. Install the heater core inlet hose (1) to the thermostat housing and engage the quick-connect coupling.
    Fig 7: Vacuum Pump & Mounting Bolts
    GC0162217Courtesy of CHRYSLER GROUP, LLC
  14. Clean the mating surfaces of the cylinder head and the vacuum pump (2).
  15. Install a new vacuum pump gasket.
  16. Align the pump drive tab with the pump drive slot located on the cam shaft and install the vacuum pump with three bolts tightened to the proper specification. Refer to TORQUE SPECIFICATIONS .
    Fig 8: Vacuum Hose Quick-Connect Coupling
    GC0172053Courtesy of CHRYSLER GROUP, LLC
  17. Install the vacuum hose (1) to the vacuum pump and engage the quick-connect coupling (1).
    Fig 9: Block Heater Power Cord & Radiator Hoses
    GC0171629Courtesy of CHRYSLER GROUP, LLC
  18. Install the upper radiator inlet hose (2) to the thermostat housing with the CLIC E®  type clamp using (special tool #10288, Pliers, Hose Clamp).
    Fig 10: Wire Harness Retainer
    GC0171271Courtesy of CHRYSLER GROUP, LLC
  19. Engage the wire harness retainer (1) to the upper radiator inlet hose at the thermostat housing.
  20. Install the battery tray and battery. Refer to TRAY, BATTERY, REMOVAL AND INSTALLATION .
    Fig 11: Quick-Connect Coupling
    GC0172014Courtesy of CHRYSLER GROUP, LLC
  21. Install the lower radiator hose (1) and fill the cooling system. Refer to STANDARD PROCEDURE .
  22. Connect the negative battery cable. If equipped with an Intelligent Battery Sensor (IBS), connect the IBS connector to the negative battery cable.
  23. Run the engine until it reaches normal operating temperature. Check the cooling system for leaks and correct fluid level. Refer to STANDARD PROCEDURE .
  24. Install the engine cover. Refer to COVER, ENGINE, REMOVAL AND INSTALLATION .
  25. Remove the support and lower the vehicle.