Safety Recall M25 / NHTSA 12V-391 Occupant Restraint Control Module (M25)
Reference number: M25
SAFETY RECALL M25 / NHTSA 12V-391 OCCUPANT RESTRAINT CONTROL MODULE
SERVICE CAMPAIGN BULLETIN
| DAIMLER CHRYSLER: | 2013 (WD) Dodge Durango |
MODELS
2013 (WD) Dodge Durango
SUBJECT
The Occupant Restraint Control (ORC) module on about 1,400 of the above vehicles may have reduced performance in the event of a side impact rearward of the second row seats. This could cause a third row seat passenger to have an increased risk of injury during certain crash conditions.
REPAIR
The Occupant Restraint Control module must be replaced.
PARTS INFORMATION
| Part Number | Description |
|---|---|
| 68025610AH | Module, Occupant Restraint Control |
Due to the small number of involved vehicles, no parts will be distributed initially. Dealers should order an ORC module for each vehicle at the time the appointment is scheduled to assure that the module is available when the customer arrives.
SPECIAL TOOLS
The following special tools are required to perform this repair:
- NPN wiTECH VCI Pod Kit
- NPN Laptop Computer
- NPN wiTECH Software
SERVICE PROCEDURE
- Apply the park brake and place the gear shift in the "Neutral" position.
- Move both front seats to the full forward position.
- Using a plastic trim stick, carefully remove and save the console right and left side rear retaining bolt access covers (Figure 1).
- Remove and save the console right and left side rear retaining bolts.
- Move the driver's seat to the full rearward position.
- Lift the battery access panel located under the passenger seat and loosen, but do not disconnect, the negative battery cable at the battery post (Figure 2).
- Move the passenger seat to the full rearward position.
- Reach under the passenger seat, lift the battery access panel and disconnect the negative battery cable from the battery post.WARNING: Make sure to isolate the negative battery cable from the negative battery post to prevent accidental airbag deployment.WARNING: Failure to disconnect and isolate the negative battery cable from the negative battery post could cause an unintended airbag deployment during the repair.WARNING: DO NOT ATTEMPT TO PERFORM THIS SERVICE PROCEDURE WITH THE BATTERY CONNECTED.
- Use the following procedure to remove the gear shift knob from the gear shift stalk:
- Remove the console top cover (Figure 5).NOTE: There are no fasteners that secure the top cover into position. This is a snap fit component.
- Carefully remove the right and left console side covers (Figure 6).
- Disconnect the gear shift electrical connectors (Figure 7).
- Remove and save the three gear shift retaining bolts (Figure 7).
- Lift the gear shift assembly up and carefully set the assembly aside.NOTE: Do not disconnect the gear shift cables from the gear shift assembly.
- Remove and save the two console lower fasteners located on the side of the console body.
- Remove and save the two console upper fasteners (Figure 8).
- Disconnect the two right side console electrical connectors.
- Unclip the wiring harness from the console.
- Disconnect the left side console electrical connectors.
- Carefully lift the console from the vehicle and remove.
- Disconnect the two Occupant Restraint Control (ORC) module yellow electrical connectors (Figure 9).
- Remove and save the three ORC module retaining nuts (Figure 9).
- Remove and discard the original ORC module.
- Install the new ORC module into position. Tighten the three ORC module retaining nuts to 80 in. lbs. (9 N.m).NOTE: When the ORC module is correctly positioned, the orientation arrow on the ORC module label will point forward in the vehicle.
- Connect the two yellow ORC module electrical connectors (Figure 9).NOTE: The yellow electrical connectors are keyed differently to prevent incorrect installation. Also make sure that the electrical connector locks are fully engaged.
- Install the console assembly into position in the vehicle.
- Install the console upper and lower fasteners.
- Connect the left and right side console electrical connectors and clip the wire harness into position.
- Move the gear shift assembly into position and install the three retaining bolts. Tighten the gear shift retaining bolts to 62 in. lbs. (7 N.m) (Figure 7).
- Install the right and left console side covers (Figure 6).
- Install the console top cover (Figure 5).
- Install the gear shift knob, retaining pin and chrome shift knob trim ring (Figures 3 and 4).
- Connect wiTECH to the vehicle.
- With no one else in the vehicle, carefully reach under the passenger seat, open the battery access panel, and connect the negative battery cable.
- Move both front seats to the full forward position.
- Open the battery access panel and tighten the negative battery cable at the battery post.
- Install the console right and left side rear retaining bolts.
- Install the console right and left side rear retaining bolt access covers.
- Move the both front seats rearward to a normal driving position.
- Carefully remove and save the "Push-to-Start" cap from the starter button and insert the key Frequency Operated Button (FOB).
- Turn the ignition key FOB to the run position and erase all Diagnostic Trouble
- Turn the key FOB to the "OFF" position.
- Wait 15 seconds and then turn the key FOB to the "RUN" position.
- Watch the instrument panel airbag warning light. It should stay on for approximately 6 to 8 seconds and then turn off.
- Turn the key FOB to the "OFF" position and remove wiTECH from the vehicle.
- Remove the key FOB from the ignition and install the "Push-to-Start" switch cap.
COMPLETION REPORTING AND REIMBURSEMENT
Claims for vehicles that have been serviced must be submitted on the DealerCONNECT Claim Entry Screen located on the Service tab. Claims submitted will be used by Chrysler to record recall service completions and provide dealer payments.
Use the following labor operation number and time allowance:
| Labor Operation Number | Time Allowance | |
|---|---|---|
| Replace Occupant Restraint Control (ORC) Module | 08-M2-51-82 | 0.7 hours |
Add the cost of the recall parts package plus applicable dealer allowance to your claim.
DEALER NOTIFICATION
To view this notification on DealerCONNECT, select "Global Recall System" on the Service tab, then click on the description of this notification.
OWNER NOTIFICATION AND SERVICE SCHEDULING
All involved vehicle owners known to Chrysler are being notified of the service requirement by first class mail. They are requested to schedule appointments for this service with their dealers. A generic copy of the owner letter is attached.
Enclosed with each owner letter is an Owner Notification postcard to allow owners to update our records if applicable.
VEHICLE LISTS, GLOBAL RECALL SYSTEM, VIP AND DEALER FOLLOW UP
All involved vehicles have been entered into the DealerCONNECT Global Recall System (GRS) and Vehicle Information Plus (VIP) for dealer inquiry as needed.
GRS provides involved dealers with an updated VIN list of their incomplete vehicles. The owner's name, address and phone number are listed if known. Completed vehicles are removed from GRS within several days of repair claim submission.
To use this system, click on the "Service" tab and then click on "Global Recall System." Your dealer's VIN list for each recall displayed can be sorted by: those vehicles that were unsold at recall launch, those with a phone number, city, zip code, or VIN sequence.
Dealers must perform this repair on all unsold vehicles before retail delivery. Dealers should also use the VIN list to follow up with all owners to schedule appointments for this repair.
Recall VIN lists may contain confidential, restricted owner name and address information that was obtained from the Department of Motor Vehicles of various states. Use of this information is permitted for this recall only and is strictly prohibited from all other use.
ADDITIONAL INFORMATION
If you have any questions or need assistance in completing this action, please contact your Service and Parts District Manager.
Customer Services / Field Operations
Chrysler Group LLC
SAFETY RECALL M25 / NHTSA 12V-391 OCCUPANT RESTRAINT CONTROL MODULE
Dear: (Name)
This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act.
Chrysler has decided that a defect, which relates to motor vehicle safety, exists in some 2013 model year Dodge Durango vehicles equipped with third row seating.
The problem is... The Occupant Restraint Control (ORC) module on your vehicle (VIN: xxxxxxxxxxxxxxxxx) may have reduced performance in the event of a side impact rearward of the second row seats. This could cause a third row seat passenger to have an increased risk of injury during certain crash conditions.
What your dealer will do... Chrysler will repair your vehicle free of charge (parts and labor). To do this, your dealer will replace the ORC module. The work will take about one hour to complete. However, additional time may be necessary depending on service schedules.
What you must do to ensure your safety... Simply contact your Chrysler, Jeep, or Dodge dealer right away to schedule a service appointment. Ask the dealer to hold the part for your vehicle or to order it before your appointment. Please bring this letter with you to your dealer.
If you need help... If you have questions or concerns which your dealer is unable to resolve, please contact the Chrysler Group Recall Assistance Center at 1-800-853-1403.
Please help us update our records by filling out the attached prepaid postcard, if any of the conditions listed on the card apply to you or your vehicle. You may also update this information on the web at www.dodge.com/ownersreg
If you have already experienced this condition and have paid to have it repaired, please send your original receipts and/or other adequate proof of payment to the following address for reimbursement: Chrysler Customer Assistance, P.O. Box 21-8007, Auburn Hills, MI 48321-8007, Attention: Reimbursement. Once we receive and verify the required documents, reimbursement will be sent to you within 60 days.
If your dealer fails or is unable to remedy this defect without charge and within a reasonable time, you may submit a written complaint to the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Ave., S.E., Washington, DC 20590, or call the toll-free Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to http://www.safercar.gov.
We're sorry for any inconvenience, but we are sincerely concerned about your safety. Thank you for your attention to this important matter.
Customer Services / Field Operations
Chrysler Group LLC
Notification Code M25
Note to lessors receiving this recall: Federal regulation requires that you forward this recall notice to the lessee within 10 days.