LEMON Manuals: Even more car manuals for everyone

Diagnostic Test

  1. 1) MTV PWM FEEDBACK 

    Start the engine and allow it to reach normal operating temperature.

    WARNING: When the engine is operating, do not stand in direct line with the fan. Do not put your hands near the pulleys, belts, or fan. Do not wear loose clothing. Failure to follow these instructions can result in personal injury or death.
    NOTE: Diagnose and repair any system voltage or sensor supply voltage DTCs before continuing with this test.

    With the scan tool, read the MTV PWM Feedback.

    Is the MTV PWM Feedback greater than 97%? 

    Yes 

    1. Go To  2).

    No 

    1. Refer to the INTERMITTENT CONDITION Diagnostic Procedure.
  2. 2) MANIFOLD TUNE VALVE ASSEMBLY 
    Fig 1: Identifying Manifold Tune Valve Assembly Connector
    GC0049699Courtesy of CHRYSLER LLC

    Turn the ignition off.

    Disconnect the Manifold Tune Valve Assembly connector.

    Connect a jumper wire between the (K900) Sensor Ground circuit and the (K234) MTV Signal circuit in the Manifold Tune Valve Assembly harness connector.

    Turn the ignition on.

    With the scan tool, read the MTV PWM Feedback.

    NOTE: The MTV PWM Feedback should be less than 3% with the jumper wire in place.

    Is the MTV PWM Feedback less than 3%? 

    Yes 

    1. Verify that there is good pin to terminal contact in the Manifold Tune Valve Assembly and Powertrain Control Module connectors. If OK, replace the Manifold Tune Valve Solenoid Assembly in accordance with the Service Information.
    2. Perform POWERTRAIN VERIFICATION TEST .

    No 

    1. Go To  3).
  3. 3) (K857) 5 VOLT SUPPLY CIRCUIT SHORTED TO VOLTAGE 
    Fig 2: Measuring Voltage Of (K857) 5 Volt Supply Circuit In Manifold Tune Valve Assembly Harness Connector
    GC0049692Courtesy of CHRYSLER LLC

    Turn the ignition off.

    Disconnect the C1 and C2 PCM harness connectors.

    Turn the ignition on.

    Measure the voltage of the (K857) 5 Volt Supply circuit in the Manifold Tune Valve Assembly harness connector.

    Is there any voltage present? 

    Yes 

    1. Repair the short to voltage in the (K857) 5 Volt Supply circuit.
    2. Perform POWERTRAIN VERIFICATION TEST .

    No 

    1. Go To  4).
  4. 4) (K234) MTV SIGNAL CIRCUIT SHORTED TO VOLTAGE 
    Fig 3: Measuring Voltage Of (K234) MTV Signal Circuit In Manifold Tune Valve Assembly Harness Connector
    GC0049700Courtesy of CHRYSLER LLC

    Measure the voltage of the (K234) MTV Signal circuit in the Manifold Tune Valve Assembly harness connector.

    Is there any voltage present? 

    Yes 

    1. Repair the short to voltage in the (K234) MTV Signal circuit.
    2. Perform POWERTRAIN VERIFICATION TEST .

    No 

    1. Go To  5).
  5. 5) (K234) MTV SIGNAL CIRCUIT SHORTED TO THE (K857) 5 VOLT SUPPLY CIRCUIT 
    Fig 4: Measuring Resistance Between (K234) MTV Signal Circuit And (K857) 5 Volt Supply In Manifold Tune Valve Assembly Harness Connector
    GC0049701Courtesy of CHRYSLER LLC

    Measure the resistance between the (K234) MTV Signal circuit and the (K857) 5 Volt Supply in the Manifold Tune Valve Assembly harness connector.

    Is the resistance below 100 ohms? 

    Yes 

    1. Repair the short between the (K234) MTV Signal circuit and the (K857) 5 Volt Supply circuit.
    2. Perform POWERTRAIN VERIFICATION TEST .

    No 

    1. Go To  6).
  6. 6) (K234) MTV SIGNAL CIRCUIT OPEN 
    Fig 5: Measuring Resistance Of (K234) MTV Signal Between Manifold Tune Valve Assembly Harness Connector And Appropriate Terminal Of Special Tool #8815
    GC0049702Courtesy of CHRYSLER LLC
    CAUTION: Do not probe the PCM harness connectors. Probing the PCM harness connectors will damage the PCM terminals, resulting in poor terminal to pin connection. Install Miller Special Tool #8815 to perform diagnosis.

    Measure the resistance of the (K234) MTV Signal between the Manifold Tune Valve Assembly harness connector and the appropriate terminal of special tool #8815.

    Is the resistance below 5.0 ohms? 

    Yes 

    1. Go To  7).

    No 

    1. Repair the open in the (K234) MTV Signal circuit.
    2. Perform POWERTRAIN VERIFICATION TEST .
  7. 7) (K900) SENSOR GROUND CIRCUIT OPEN 
    Fig 6: Measuring Resistance Of (K900) Sensor Ground Circuit Between Manifold Tune Valve Assembly Harness Connector And Appropriate Terminal Of Special Tool #8815
    GC0049698Courtesy of CHRYSLER LLC
    CAUTION: Do not probe the PCM harness connectors. Probing the PCM harness connectors will damage the PCM terminals, resulting in poor terminal to pin connection. Install Miller Special Tool #8815 to perform diagnosis.

    Measure the resistance of the (K900) Sensor Ground circuit between the Manifold Tune Valve Assembly harness connector and the appropriate terminal of special tool #8815.

    Is the resistance below 5.0 ohms? 

    Yes 

    1. Go To  8).

    No 

    1. Repair the open in the (K900) Sensor Ground circuit.
    2. Perform POWERTRAIN VERIFICATION TEST .
  8. 8) POWERTRAIN CONTROL MODULE (PCM) 

    Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between the Manifold Tune Valve Assembly and the Powertrain Control Module (PCM).

    Look for any chafed, pierced, pinched, or partially broken wires.

    Look for broken, bent, pushed out or corroded terminals. Verify that there is good pin to terminal contact in the Manifold Tune Valve Assembly and Powertrain Control Module connectors.

    Refer to any Technical Service Bulletins that may apply.

    Were any problems found? 

    Yes 

    1. Repair as necessary.
    2. Perform POWERTRAIN VERIFICATION TEST .

    No 

    1. Replace and program the Powertrain Control Module (PCM) in accordance with the Service Information.
    2. Perform POWERTRAIN VERIFICATION TEST .