LEMON Manuals: Even more car manuals for everyone

Test NTC-7: Checking Fuel Delivery (3.0L)

    WARNING: Fuel system is under high pressure and fuel pressure must be released before opening fuel system.
  1. Release fuel pressure. See FUEL SYSTEM PRESSURE RELEASE  . Connect Fuel Pressure Adapter (6433) and fuel pressure gauge at fuel supply line, located at front of fuel rail, near air intake plenum.
  2. Turn ignition on with engine off. Using scan tool, actuate ASD fuel system test and note fuel pressure. Fuel pressure should be 43-53 psi (3.0-3.7 kg/cm2 ). Record fuel pressure. If fuel pressure is within specification, go to next step. If fuel pressure exceeds specification, go step  10 . If fuel pressure is less than specified, go to step  12 .
  3. Turn ignition off. Apply parking brake. Place shift lever in Neutral. Start engine. While monitoring fuel pressure, momentarily fully open throttle until engine speed is more than 3000 RPM. If fuel pressure does not decrease to less than 35 psi, (2.5 kg/cm2 ) at any time, go to next step. If fuel pressure decreases to less than 35 psi, (2.5 kg/cm2 ) at any time, go to  7 .
  4. Turn ignition off. Release fuel pressure. Remove fuel pressure gauge. Reinstall fuel supply line if fuel pump volume is not being checked. If necessary to check fuel pump volume, connect Fuel Line Adapter (6539 for 5/16" fuel line or 6631 for 3/8" fuel line) to disconnected fuel supply line. Place other end of fuel line adapter in graduated cylinder.
  5. Turn ignition on with engine off. Using scan tool, actuate ASD fuel system test to operate fuel pump for no more than 7 seconds and note fuel pump volume. DO NOT operate fuel pump for more than 7 seconds or fuel pump may be damaged. Stop ASD fuel system test.
  6. Fuel pump volume should be at least .52 pint (.25 liter) in 7 seconds. If fuel pump volume is within specification, remove fuel line adapter, reconnect fuel supply line. Test is complete. If fuel pump volume is not within specification, remove fuel line adapter and reconnect fuel supply line. Check for restricted chassis fuel supply line between fuel rail and fuel pump module on top of fuel tank. See Figure . Fuel pump module may also be referred to as fuel tank module. If no kinks or restrictions exist on chassis fuel supply line, improper fuel pump volume may be caused by defective fuel pressure regulator, defective fuel pump or restricted fuel pump inlet strainer on end of fuel pump.
  7. Shut engine off. Inspect chassis fuel supply line from fuel pump module on top of fuel tank to fuel rail for kinks or restrictions. See Figure . If no kinks or restrictions exist on chassis fuel supply line, go to next step. If kink or restriction exist in chassis fuel supply line, release fuel pressure and repair or replace chassis fuel supply line as necessary. Perform TEST VER-2A  .
  8. Ensure ignition is off. Release fuel pressure. Remove fuel pressure gauge. Reinstall fuel supply line. Remove fuel filter. Fuel filter is located on top of fuel tank, near fuel pump module. See Figure . Fuel lines are permanently attached to fuel filter. When removing fuel filter, disconnect fuel lines at fuel pump module and fuel supply line.
  9. Using shop air, apply 40 psi (2.8 kg/cm2 ) air pressure to fuel inlet passage on fuel filter while checking fuel filter for restrictions. If fuel filter is restricted, replace fuel filter. Perform TEST VER-2A  . If fuel filter is not restricted, replace fuel pump and fuel pressure regulator. Fuel pressure regulator is mounted on bottom of fuel pump module located on top of fuel tank. Perform TEST VER-2A  .
  10. Turn ignition off. Release fuel pressure. Remove fuel pressure gauge. Reinstall fuel supply line. Remove fuel return line between fuel pump module and fuel filter. See Figure .
  11. Using shop air, apply 40 psi (2.8 kg/cm2 ) air pressure to fuel return line while checking fuel return line for restrictions. If fuel return line is restricted, replace fuel return line. Perform TEST VER-2A  . If fuel return line is not restricted, replace fuel pressure regulator. Fuel pressure regulator is mounted on bottom of fuel pump module located on top of fuel tank. Perform TEST VER-2A  .
  12. Turn ignition off. Inspect chassis fuel supply line from fuel pump module on top of fuel tank to fuel rail for kinks or restrictions. See Figure . If no kinks or restrictions exist on chassis fuel supply line, go to next step. If kinks or restrictions exist in chassis fuel supply line, release fuel pressure and repair or replace chassis fuel supply line as necessary. Perform TEST VER-2A  .
  13. Ensure ignition is off. Release fuel pressure. Install fuel pressure adapter and fuel pressure gauge on fuel supply line between fuel tank module and fuel filter. Fuel filter is located on top of fuel tank, near fuel pump module. See Figure .
  14. Turn ignition on with engine off. Using scan tool, actuate ASD fuel system test. Note fuel pressure. If fuel pressure is at least 5 psi (.35 kg/cm2 ) more than that recorded in step 2)  , stop actuation of ASD fuel system test. Release fuel pressure. Replace fuel filter. Perform TEST VER-2A  . If fuel pressure is not at least 5 psi (.35 kg/cm2 ) more than that recorded in step 2)  , stop actuation of ASD fuel system test. Release fuel pressure. Replace fuel pump and fuel pressure regulator. Fuel pressure regulator is mounted on bottom of fuel pump module located on top of fuel tank. Perform TEST VER-2A  .