LEMON Manuals: Even more car manuals for everyone

Final Drive: Assembly

NOTE: The differential is serviced as an assembly. Differential service is limited to bearing cups and cones. Any other differential component failure must be remedied by differential assembly and transfer shaft replacement.
  1. Install side gear thrust washer to differential case. See Fig 1.
    Fig 1: Removing/Installing Thrust Washer
    GC0000750Courtesy of DAIMLERCHRYSLER CORP.
    1 - THRUST WASHER
  2. Install side gear to differential case. See Fig 2.
    Fig 2: Removing/Installing Side Gear
    GC0000749Courtesy of DAIMLERCHRYSLER CORP.
    1 - DIFFERENTIAL SIDE GEAR
  3. Install both pinion gears and washers to case, while orientating washer tabs to notch in case. See Fig 3.
    Fig 3: Removing/Installing Pinion Gear and Washer
    GC0000748Courtesy of DAIMLERCHRYSLER CORP.
    1 - PINION GEAR
    2 - TABBED WASHER
    3 - LOCATING TAB
    4 - NOTCH
  4. Install pinion shaft. See Fig 4.
    Fig 4: Removing/Installing Pinion Shaft
    GC0000732Courtesy of DAIMLERCHRYSLER CORP.
    1 - PINION SHAFT
  5. Install side gear to case. See Fig 5.
    Fig 5: Removing/Installing Side Gear
    GC0000733Courtesy of DAIMLERCHRYSLER CORP.
    1 - DIFFERENTIAL SIDE GEAR
  6. Install side gear thrust washer to case. See Fig 6.
    Fig 6: Removing/Installing Side Gear Thrust Washer
    GC0000734Courtesy of DAIMLERCHRYSLER CORP.
    1 - SIDE GEAR THRUST WASHER
  7. Install differential support into position, while aligning through-holes. See Fig 7.
    Fig 7: Removing/Installing Differential Support
    GC0000735Courtesy of DAIMLERCHRYSLER CORP.
    1 - DIFFERENTIAL SUPPORT
    2 - DIFFERENTIAL CASE
  8. Install differential ring gear to case. See Fig 8.
    Fig 8: Removing/Installing Ring Gear
    GC0000737Courtesy of DAIMLERCHRYSLER CORP.
    1 - DIFFERENTIAL CASE
    2 - RING GEAR
  9. Install ring gear-to-case bolts, with pinion shaft retainers, and torque bolts to 95 N.m (70 ft. lbs.). See Fig 9.
    Fig 9: Ring Gear-to-Case Bolts
    GC0000738Courtesy of DAIMLERCHRYSLER CORP.
    1 - DIFFERENTIAL CASE
    2 - PINION SHAFT RETAINER
    3 - RING GEAR
    4 - RING GEAR-TO-CASE BOLT
  10. Using Miller Special Tool L-4410, and C-4171, install differential bearing to differential (extension housing side). See Fig 10.
    Fig 10: Position Bearing Cone Onto Differential (Typical)
    GC0000751Courtesy of DAIMLERCHRYSLER CORP.
    1 - DIFFERENTIAL ASSEMBLY
    2 - DIFFERENTIAL BEARING
  11. Using Miller Special Tool 5052 and C-4171, install differential bearing to differential (bearing retainer side).
  12. Using Miller Special Tool 6061 and C-4171, install differential bearing race to bearing retainer. See Fig 11.
    Fig 11: Differential Bearing Retainer
    GC0000752Courtesy of DAIMLERCHRYSLER CORP.
    1 - DIFFERENTIAL BEARING CUP
    2 - DIFFERENTIAL BEARING RETAINER
  13. Using Miller Special Tool L-4520 and C-4171, install differential bearing to extension housing.
    NOTE: Use Mopar® Silicone Rubber Adhesive Sealant, or equivalent, on retainer and extension housing/adapter plate to seal to case.
  14. Install differential assembly into transaxle case. See Fig 12 Install differential bearing retainer and torque retainer-to-case bolts to 28 N.m (21 ft. lbs.). See Fig 13.
    Fig 12: Differential Bearing Retainer
    GC0000752Courtesy of DAIMLERCHRYSLER CORP.
    1 - DIFFERENTIAL BEARING CUP
    2 - DIFFERENTIAL BEARING RETAINER
    Fig 13: Differential Retainer Bolts
    GC0000741Courtesy of DAIMLERCHRYSLER CORP.
    1 - DIFFERENTIAL RETAINER BOLTS
  15. Apply a bead of Mopar® Silicone Rubber Adhesive Sealant to extension housing/adapter plate and install into position. Install and torque bolts to 28 N.m (21 ft. lbs.).
  16. Measure and adjust differential bearing preload. (Refer to TRANSMISSION/TRANSAXLE/AUTOMATIC - 41TE/FINAL DRIVE - ADJUSTMENTS) 
  17. Apply a bead of Mopar® Silicone Rubber Adhesive Sealant to differential cover and install to case. See Fig 14.
    Fig 14: Differential Cover Sealant Application
    GC0000740Courtesy of DAIMLERCHRYSLER CORP.
    1 - DIFFERENTIAL ASSEMBLY
    2 - DIFFERENTIAL COVER
  18. Install and torque cover-to-case bolts to 19 N.m (165 in. lbs.). See Fig 15.
Fig 15: Differential Cover Bolts
GC0000739Courtesy of DAIMLERCHRYSLER CORP.
1 - DIFFERENTIAL COVER BOLTS
2 - DIFFERENTIAL COVER