LEMON Manuals: Even more car manuals for everyone

Installation - Engine Assembly

WARNING: This page is about a different variant/trim than selected.
CAUTION: While slowly lowering the body to the cradle assembly, constantly check to assure proper positioning and no damage occurs to other components until union is made.
  1. Position engine and transmission assembly under vehicle. Slowly lower the vehicle down over the engine and transmission until the cradle is aligned.
  2. Install the cradle supporting bolts and tighten to 163 N.m (120 ft.lbs.). See Figure.
  3. Install the right engine mount. tighten the bolts to the timing cover to 54 N.m (40 ft.lbs.), tighten the bolts to the right rail to 68 N.m (50 ft.lbs.). See Fig 1.
    Fig 1: Right Engine Mount to Engine
    GC0002022Courtesy of DAIMLERCHRYSLER CORP.
    1 - BOLT
    2 - MOUNT BRACKET
    3 - ENGINE RIGHT MOUNT ASSEMBLY
  4. Slowly raise the vehicle off of the cradle support.
    Fig 2: Powertrain Torque Strut
    GC0000561Courtesy of DAIMLERCHRYSLER CORP.
    1 - STRUT
    2 - BRACKET
  5. Install the rear transmission torque strut and tighten bolts to 54 N.m (40 ft. lbs.). See Fig 2.
  6. Install the engine wiring harness ground strap to transmission case.
  7. Connect the left front strut to steering knuckle. Tighten bolts to 81 N.m (60 ft. lbs.) plus 90 degrees.
  8. Connect the left stabilizer link. Tighten to 88N.m (65 ft.lbs.).
    Fig 3: Wheel Speed Sensor Mounting to Strut
    GC0000552Courtesy of DAIMLERCHRYSLER CORP.
    1 - STRUT ASSEMBLY
    2 - SCREW
    3 - WHEEL SPEED SENSOR ROUTING BRACKET
  9. Connect the left wheel speed sensor and harness push pin. See Fig 3.
    Fig 4: Steering Column Coupling
    GC0001792Courtesy of DAIMLERCHRYSLER CORP.
    1 - LOWER STEERING COLUMN COUPLING ASSEMBLY
    2 - INTERMEDIATE SHAFT TO STEERING GEAR
    3 - PIN
    4 - STEERING GEAR
    5 - EXTENSION TO SHAFT BOLT
  10. Reconnect the steering column intermediate shaft to the steering gear. See Fig 4.
  11. Connect the right front strut to steering knuckle. Tighten bolts to 81 N.m (60 ft. lbs.) plus 90 degrees. See Figure
  12. Connect the right stabilizer link. Tighten to 88N.m (65 ft.lbs.). See Figure.
  13. Connect the right wheel speed sensor and harness push pin. See Fig 3.
  14. Install wheels.
  15. Connect the in block heater (if equipped).
  16. Connect the knock sensor electrical connector.
  17. Install the exhaust system and connect the O2 sensor.
  18. Install the torque converter bolts. Tighten the bolts to 88N.m (65 ft.lbs.).
  19. Install the flex plate inspection cover.
  20. Connect the starter wiring, route harness and secure with push pin.
  21. Install the front fascia.
  22. Connect the coolant hose at the engine oil cooler.
  23. Connect the oil pressure sending unit (OPS) wiring harness connector.
  24. Lower the vehicle.
  25. Connect the A/C lines and compressor electrical connector (Refer to HEATING & AIR CONDITIONING/PLUMBING/A/C COMPRESSOR - INSTALLATION) .
  26. Route the engine harness to the left cylinder head and attach the purge solenoid.
  27. Connect the engine sensor wiring harness connectors.
  28. Connect the engine vacuum harnesses.
  29. Connect the fuel line to the fuel rail.
  30. Connect the generator electrical connectors (Refer to ELECTRICAL/CHARGING/GENERATOR - INSTALLATION) .
    Fig 5: Transmission Connectors
    GC0000554Courtesy of DAIMLERCHRYSLER CORP.
    1 - SOLENOID PACK CONNECTOR
    2 - INPUT SPEED SENSOR CONNECTOR
    3 - OUTPUT SPEED SENSOR CONNECTOR
    4 - TRANSMISSION RANGE SENSOR CONNECTOR
  31. Connect the transmission controller, sensor electrical connectors and fluid lines. See Fig 5.
  32. Connect the radiator, coolant reservoir and heater hoses.
    Fig 6: Throttle Body
    GC0001794Courtesy of DAIMLERCHRYSLER CORP.
    1 - THROTTLE BODY
    2 - SPEED CONTROL CABLE ACCESS
    3 - THROTTLE CABLE
  33. Connect the throttle and cruise control cables. See Fig 6.
  34. Install the air cleaner housing and connect the CCV hose to the left cylinder head cover (Refer to ENGINE/AIR INTAKE SYSTEM/AIR CLEANER ELEMENT - INSTALLATION)  .
  35. Fill the cooling system (Refer to COOLING - STANDARD PROCEDURE) .
  36. Evacuate and recharge A/C system (Refer to REFRIGERANT SYSTEM EVACUATE ).
  37. Install new oil filter. Fill engine crankcase with proper oil to correct level (Refer to LUBRICATION & MAINTENANCE/FLUID TYPES - SPECIFICATIONS) .
  38. Connect negative cable to battery.
  39. Fill the cooling system (Refer to COOLING - STANDARD PROCEDURE) .
  40. Bleed the braking system (Refer to BRAKES - STANDARD PROCEDURE) - BASE or (Refer to BRAKES - STANDARD PROCEDURE) - ABS .
  41. Start engine and run until operating temperature is reached.