Test TC-10A - Auto Shutdown Relay Control Circuit
NOTE:
For connector terminal identification, see CONNECTOR IDENTIFICATION in SELF-DIAGNOSTICS section in this article. For wiring diagram, see WIRING DIAGRAMS - 3.2L
article.
- Using scan tool, actuate Auto Shutdown (ASD) relay. Listen for clicking sound at ASD relay. ASD relay is located in Power Distribution Center (PDC) in engine compartment. If ASD relay is clicking, go to next step. If ASD relay is not clicking, go to step 5).
- Condition to set trouble code is not present at this time. AUTO SHUTDOWN RELAY CONTROL CIRCUIT DTC sets if an open or shorted condition is detected in ASD relay control circuit. Possible causes are: ASD relay coil open or shorted, fused ignition switch circuit open, ASD relay control circuit open or shorted, inoperative driver in Powertrain Control Module (PCM), PCM failure, faulty connections or wiring. Go to next step.
- Inspect all related wiring and connectors and repair as necessary. If no problems were found with wiring and connectors, go to next step. If related wiring and connectors were repaired, perform TEST VER-2A.
- Start engine. Wiggle wiring harness from ASD relay to PCM. If engine stalled, repair wiring harness as necessary. Perform TEST VER-2A. If engine did not stall, see INACTIVE TROUBLE CODE CONDITION in SELF-DIAGNOSTICS section in this article. Test is complete. Perform TEST VER-2A.
- Disconnect ASD relay. Using a voltmeter, check voltage of both ASD relay connector fused B+ circuits. See ASD RELAY CONNECTOR WIRE IDENTIFICATION table. When checking fused B+ circuit, ensure circuit is tested at both terminals (one at a time) of ASD relay connector. ASD relay is located in underhood Power Distribution Center (PDC). If voltage is more than 10 volts, go to next step. If voltage is 10 volts or less, repair open fused B+ circuit. See ASD RELAY CONNECTOR WIRE IDENTIFICATION table. Perform TEST VER-2A.
- Using an ohmmeter, check resistance between ASD relay terminals No. 85 and 86. See Fig 1 . If resistance is less than 100 ohms, go to next step. If resistance is 100 ohms or more, replace ASD relay. Perform TEST VER-2A.
- Turn ignition off. Disconnect Powertrain Control Module (PCM) connector. Using an ohmmeter, check resistance of ASD relay control circuit at ASD relay connector. See ASD RELAY CONNECTOR WIRE IDENTIFICATION table for wire identification. If resistance is 5 ohms or more, go to next step. If resistance is less than 5 ohms, repair short to ground in ASD relay control circuit. Perform TEST VER-2A.
- Using an ohmmeter, measure resistance of ASD relay control circuit between ASD relay connector and PCM connector. See ASD RELAY CONNECTOR WIRE IDENTIFICATION table and PCM CONNECTOR WIRE IDENTIFICATION table for wire identification. If resistance is less than 5 ohms, replace PCM. Perform TEST VER-2A. If resistance is 5 ohms or more, repair open ASD relay control circuit. Perform TEST VER-2A.
ASD RELAY CONNECTOR WIRE IDENTIFICATION
| Application | Wire Color |
|---|---|
| ASD Relay B+ Circuit Terminals A & B | Red/White |
| ASD Relay Control Circuit Terminal C | Dark Blue/Yellow |
| ASD Relay Output Circuit Terminals D | Dark Green/Orange |
PCM CONNECTOR WIRE IDENTIFICATION
| Application | Wire Color | ||
|---|---|---|---|
| PCM Terminal No. 1 Ignition Coil No. 4 Driver Circuit | Tan/Light Green | ||
| PCM Terminal No. 2 Ignition Coil No. 3 Driver Circuit | Tan/Orange | ||
| PCM Terminal No. 3 Ignition Coil No. 2 Driver Circuit | Tan/Pink | ||
| PCM Terminal No. 4 Ignition Coil No. 6 Driver Circuit | Tan/Light Blue | ||
| PCM Terminal No. 5 Speed Control Power Supply Circuit | Yellow/Red | ||
| PCM Terminal No. 6 ASD Relay Output Circuit | Dark Green/Orange | ||
| PCM Terminal No. 7 Injector No. 3 Driver Circuit | Yellow/White | ||
| PCM Ground Circuit PCM Terminal No. 10 | Black/Tan | ||
| PCM Terminal No. 11 Ignition Coil No. 1 Driver Circuit | Tan/Red | ||
| PCM Terminal No. 13 Injector No. 1 Driver Circuit | White/Dark Blue | ||
| PCM Terminal No. 14 Injector No. 6 Driver Circuit | Brown/Black | ||
| PCM Terminal No. 15 Injector No. 5 Driver Circuit | Gray | ||
| PCM Terminal No. 16 Injector No. 4 Driver Circuit | Light Blue/Brown | ||
| PCM Terminal No. 17 Injector No. 2 Driver Circuit | Tan | ||
| PCM Terminal No. 18 SRV Solenoid Control Circuit | Gray/Pink | ||
| PCM Fused Ignition Switch Output Circuit PCM Terminal No. 20 | Dark Blue/White | ||
| PCM Terminal No. 21 Ignition Coil No. 5 Driver Circuit | Tan/Dark Green | ||
| PCM Terminal No. 24 Knock Sensor Signal Circuit | Dark Blue/Light Green | ||
| PCM Terminal No. 25 Knock Sensor Ground Circuit | Black/Violet | ||
| PCM Terminal No. 26 ECT Sensor Signal Circuit | Tan/Black | ||
| PCM Terminal No. 29 O2S 2/1 Sensor Signal Circuit | Light Green/Red | ||
| Starter Relay Control Circuit PCM Terminal No. 31 | Tan/White | ||
| PCM Terminal No. 32 CKP Sensor Signal Circuit | Gray/Black | ||
| PCM Terminal No. 34 EGR Sensor Signal Circuit | Light Green/Pink | ||
| PCM Terminal No. 36 MAP Sensor Signal Circuit | Dark Green/Red | ||
| PCM Terminal No. 37 IAT Sensor Signal Circuit | Black/Red | ||
| PCM Terminal No. 40 EGR Solenoid Control Circuit | Gray/Yellow | ||
| PCM Terminal No. 41 Speed Control Switch Signal Circuit | Red/Light Green | ||
| PCM Terminal No. 42 A/C Pressure Sensor Signal Circuit | Dark Blue | ||
| PCM Terminal No. 43 A/C Pressure Sensor Ground Circuit | Black/Light Blue | ||
| PCM Terminal No. 45 Power Steering Pressure Switch Sense Circuit | Dark Blue/Light Green | ||
| PCM Fused B+ Circuit PCM Terminal No. 46 | Red/White | ||
| PCM Ground Circuit PCM Terminal No. 47 | Black/White | ||
| PCM Terminal No. 48 IAC Driver No. 3 Circuit | Brown/White | ||
| PCM Terminal No. 49 IAC Driver No. 2 Circuit | Yellow/Black | ||
| PCM Terminal No. 50 Ground | Black/Tan | ||
| PCM Terminal No. 51 O2S 1/2 Signal Circuit | Tan/White | ||
| PCM Terminal No. 53 O2S 2/2 Signal Circuit | Pink/White | ||
| PCM Terminal No. 55 Low Speed Radiator Fan Relay Control Circuit | Dark Blue/Pink | ||
| PCM Terminal No. 56 Speed Control Vacuum Solenoid Control Circuit | Tan/Red | ||
| PCM Terminal No. 57 IAC Driver No. 1 Circuit | Gray/Red | ||
| PCM Terminal No. 58 IAC Driver No. 4 Circuit | Violet/Black | ||
| PCM Terminal No. 61 MAP Sensor 5-Volt Supply Circuit | Violet/White | ||
| PCM Terminal No. 62 Brake Switch Sense Circuit | White/Pink | ||
| SCI Transmit Circuit PCM Terminal No. 65 | Dark Blue | ||
| PCM Terminal No. 67 ASD Relay Control Circuit | Dark Blue/Yellow | ||
| PCM Terminal No. 69 High Speed Radiator Fan Relay Control Circuit | Dark Blue/Light Green | ||
| PCM Terminal No. 72 LDP Switch Sense Circuit | (1) Orange | ||
| PCM Terminal No. 74 Fuel Pump Relay Control Circuit | Brown | ||
| SCI Receive Circuit PCM Terminal No. 75 | Light Green | ||
| PCM Terminal No. 76 Park/Neutral Switch Sense Circuit | Black/Yellow | ||
| PCM Terminal No. 77 LDP Solenoid Control Circuit | White/Dark Green | ||
| PCM Terminal No. 80 Speed Control Vent Solenoid Control Circuit | Light Green/Red | ||
|
|||