LEMON Manuals: Even more car manuals for everyone

Circuit/System Testing

WARNING: This page is about a different car, the 2010 Chevrolet Camaro. However, it is still accessible from the selected car via links, so may be relevant.

Dome Lamp Switch Malfunction

  1. Ignition OFF, disconnect the harness connector at the E37A dome/reading lamps.
  2. Scan tool OFF, doors CLOSED, interior lamps OFF, test for less than 5 Ω between the ground circuit terminal 6 and ground.
    • If greater than the specified range, test the ground circuit for an open/high resistance
  3. Ignition ON, verify the scan tool Interior/Courtesy Lighting Master Switch parameter is Inactive.
    • If not the specified value, test the signal circuit terminal 4 for a short to ground. If the circuit tests normal, replace the K9 BCM
  4. Verify the scan tool Dome Lamp Switch parameter is Inactive.
    • If not the specified value, test the signal circuit terminal 5 for a short to ground. If the circuit tests normal, replace the K9 BCM.
  5. Connect a 3 A fused jumper wire between the signal circuit terminal 4 and ground. Verify the scan tool Interior/Courtesy Lighting Master Switch parameter is Active.
    • If not the specified value, test the signal circuit terminal 4 for a short to B+ or an open/high resistance. If the circuit tests normal, replace the K9 BCM.
  6. Connect a 3 A fused jumper wire between the signal circuit terminal 5 and ground. Verify the scan tool Dome Lamp Switch parameter is Active.
    • If not the specified value, test the signal circuit terminal 5 for a short to voltage or an open/high resistance. If the circuit tests normal, replace the K9 BCM.
  7. If all circuits test normal, replace the E37A dome/reading lamps.

Dome Lamp Malfunction

  1. Ignition OFF, disconnect the harness connector at the E37A dome/reading lamps.
  2. Test for less than 5 Ω between the ground circuit terminal 6 and ground.
    • If greater than the specified range, test the ground circuit for an open/high resistance.
  3. Connect a test lamp between the control circuit terminal 2 and ground.
  4. Ignition ON, command the Courtesy Lamps Duty Cycle Command ON and OFF with a scan tool, the test lamp should turn ON and OFF while changing between the commanded states.
    • If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the K9 BCM.
    • If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K9 BCM.
  5. If all circuits test normal, test or replace the E37A dome/reading lamps.

Accent Lamp Malfunction

  1. Ignition OFF, disconnect the harness connector at the appropriate E1 accent lamp.
  2. Test for less than 5 Ω between the ground circuit terminal A and ground.
    • If greater than the specified range, test the ground circuit for an open/high resistance.
  3. Connect a test lamp between the control circuit terminal B and ground.
  4. Ignition ON, command the 1st Row Interior/Courtesy Lamps Command ON and OFF with a scan tool, the test lamp should turn ON and OFF while changing between the commanded states.
    • If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the K9 BCM.
    • If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K9 BCM.
  5. If all circuits test normal, test or replace the E1 accent lamp.

Rear Compartment Courtesy Lamp Malfunction

  1. Ignition OFF, disconnect the harness connector at the E8S rear compartment courtesy lamp.
  2. Test for less than 5 Ω between the ground circuit terminal 2 and ground.
    • If greater than the specified range, test the ground circuit for an open/high resistance.
  3. Connect a test lamp between the control circuit terminal 1 and ground.
  4. Ignition ON, command the Trunk Lamp Command ON and OFF with a scan tool, the test lamp should turn ON and OFF while changing between the commanded states.
    • If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the K9 BCM.
    • If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K9 BCM.
  5. If all circuits test normal, test or replace the E8S rear compartment courtesy lamp.