LEMON Manuals: Even more car manuals for everyone

Diagnostic Aids

DTC P0223

Step Action Values Yes No
Schematic Reference: Engine Controls Schematics
Connector End View Reference: Engine Controls Connector End Views or Engine Control Module (ECM) Connector End Views
1 Did you perform the Diagnostic System Check - Vehicle? - Go to Step 2  Go to Diagnostic System Check - Vehicle
2
  1. Turn ON the ignition, with the engine OFF.
  2. Observe the TP sensor 2 voltage parameter with a scan tool.
Is the voltage more than the specified value?
4.6 V Go to Step 4  Go to Step 3 
3
  1. Observe the Freeze Frame/Failure Records for this DTC.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Did the DTC fail this ignition?
- Go to Step 4  Go to Diagnostic Aids
4
  1. Turn OFF the ignition.
  2. Disconnect the throttle body harness connector.
  3. Turn ON the ignition, with the engine OFF.
  4. Measure the voltage from the TP sensor 2 5-volt reference circuit to a good ground with a DMM.
Does the DMM indicate voltage within the specified range?
4.8-5.2 V Go to Step 5  Go to Step 10 
5 Probe the TP sensor signal circuit with a test lamp connected to ground.
Does the test lamp illuminate?
- Go to Step 8  Go to Step 6 
6 Observe the TP Sensor 2 parameter with a test lamp still connected to the TP sensor signal circuit.
Does the scan tool indicate voltage at the specified value?
0 V Go to Step 9  Go to Step 7 
7 Test the TP sensor 2 signal circuit for an open or for high resistance. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
- Go to Step 16  Go to Step 13 
8 Test the signal 2 circuit of the TP sensor for a short to voltage. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
- Go to Step 16  Go to Step 12 
9 Test the TP sensor 2 low reference circuit for an open or for high resistance. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
- Go to Step 16  Go to Step 12 
10 Test the TP sensor 2 5-volt reference circuit for a short to voltage. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
- Go to Step 16  Go to Step 11 
11 Test for shorted terminals and for poor connections at the ECM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
- Go to Step 16  Go to Step 15 
12 Test for an intermittent and for a poor connection at the throttle body harness connector. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
- Go to Step 16  Go to Step 14 
13 Test for an intermittent and for a poor connection at the ECM harness connector. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
- Go to Step 16  Go to Step 15 
14 Replace the throttle body assembly. Refer to Throttle Body Removal .
Did you complete the replacement?
- Go to Step 16  -
15 Replace the ECM. Refer to Control Module References for replacement, setup, and programming.
Did you complete the replacement?
- Go to Step 16  -
16
  1. Clear the DTCs with a scan tool.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Did the DTC fail this ignition?
- Go to Step 2  Go to Step 17 
17 Observe the Capture Info with a scan tool.
Are there any DTCs that have not been diagnosed?
- Go to Diagnostic Trouble Code (DTC) List - Vehicle System OK