LEMON Manuals: Even more car manuals for everyone

Diagnostic Procedures

  1. Perform diagnostic system check - engine controls. See DIAGNOSTIC SYSTEM CHECK - ENGINE CONTROLS  under SELF-DIAGNOSTIC SYSTEM. After performing diagnostic system check - engine controls, go to next step.
  2. Start and operate engine at a normal operating temperature. Does the engine run rough, or is the idle unstable? If yes, go to step  8 . If no, go to next step.
  3. Install a scan tool. Perform the scan tool Clear DTC Information function. Start engine. Using the scan tool, gradually command the EGR valve OPEN to 50 percent and then back to zero percent. Did the engine run rough when commanded to 50 percent and then idle smoothly when commanded to zero percent? If yes, go to step  6 . If no, go to next step.
  4. Start engine. Backprobe EGR coil control circuits at PCM harness connector terminals C4-4 and C4-17 with a test light connected to ground. Test light should illuminate on both circuits. Continue to backprobe both EGR control circuits with test light. Observe test light on each circuit while commanding EGR valve OPEN to 5%. Test light should illuminate and then turn OFF when EGR valve is commanded OPEN. Does EGR valve pass both tests? If yes, go to next step. If no, go to step  11 .
  5. Start engine. Backprobe EGR coil control circuits at PCM harness connector terminals C4-5 and C4-16 with a test light connected to ground. Test light should NOT illuminate on either circuit. Continue to backprobe both EGR control circuits with test light. Observe test light on each circuit while commanding EGR valve OPEN to 5%. Test light should illuminate when EGR valve is commanded OPEN. Does EGR valve pass both tests? If yes, go to step  13 . If no, go to step  11 .
  6. Inspect the vehicle for any condition that can affect the accuracy of the Manifold Absolute Pressure (MAP) sensor: A malfunctioning or incorrectly calibrated MAP sensor, faulty manifold vacuum supply to the MAP sensor, or an engine performance concern that can affect the engine manifold vacuum readings. Repair as necessary. Did you find and correct Condition? If yes, go to step  15 . If no, go to next step.
  7. The fault is not present. Are there any DTCs stored that have not been diagnosed? If yes, see DIAGNOSTIC TROUBLE CODE DEFINITIONS  . If no, DIAGNOSTIC AIDS  .
  8. With the engine running, disconnect the EGR valve electrical connector. Does the engine performance improve when the EGR valve is disconnected? If yes, go to step  10 . If no, go to next step.
  9. Remove the EGR valve. Inspect the EGR valve for sticking open. Inspect EGR valve and gasket for leaks. Repair Condition or replace the EGR valve. After repairs, go to step  15 .
  10. Inspect the EGR coil control circuits for an open or a short to ground. Repair as necessary. Did you find and correct Condition? If yes, go to step  15 . If no, go to step  14 .
  11. Turn ignition off. Disconnect EGR valve electrical connector. Use DVOM to measure resistance between EGR valve terminals No. 1 and 2, between terminals No. 2 and 3, between terminals No. 5 and 6, between terminals No. 4 and 5. Resistance should be 20-24 ohms at 68°F (20°C). Measure resistance between terminals No. 2 and 5 and EGR assembly body. Resistance should be infinite. Does EGR valve pass all resistance tests? If yes, go to next step. If no, go to step  13 .
  12. Inspect for an open or a short in the EGR coil control circuits that did not illuminate On and Off in step  4 or step  5 . Repair as necessary. Did you find and correct Condition? If yes, go to step  15 . If no, go to step  14 .
  13. Replace EGR valve. After repairs, go to step  15 .
  14. Replace PCM. Perform PCM relearn procedure. See POWERTRAIN CONTROL MODULE  under PROGRAMMING. After replacing PCM, go to next step.
  15. Turn ignition off. Remove DOME fuse for 30 seconds. Install DOME fuse. Reset radio clock time. Start engine. Operate the vehicle within the Conditions for Running the DTC or until the DTC P0402 diagnostic test has run. See CONDITIONS FOR RUNNING DTC  . Does the DTC run and pass? If yes, go to next step. If no, go to step  2 .
  16. Using scan tool, observe stored information and Capture Info. Does the scan tool display any DTCs that you have not diagnosed? If yes, see DIAGNOSTIC TROUBLE CODE DEFINITIONS  . If no, system is okay.