LEMON Manuals: Even more car manuals for everyone

Diagnostic Procedures

  1. Perform diagnostic system check - engine controls. See DIAGNOSTIC SYSTEM CHECK - ENGINE CONTROLS  under SELF-DIAGNOSTIC SYSTEM. After performing diagnostic system check - engine controls, go to next step.
  2. Is DTC P0403 also set? If yes, go to DTC P0403: EGR SOLENOID CONTROL CIRCUIT  . If no, go to next step.
  3. Install a scan tool. Perform the scan tool Clear DTC Information function. Start engine. Using scan tool, gradually command EGR valve OPEN to 100 percent. Does the engine run rough or stall? If yes, go to step  9 . If no, go to next step.
  4. Start engine. Backprobe EGR coil control circuits PCM harness connector terminals C4-4 and C4-17 with a test light connected to ground. The test light should illuminate on both circuits. Continue to backprobe both EGR control circuits with the test light. Observe the test light on each circuit while commanding EGR valve OPEN to 5% with scan tool. The test light should illuminate and then turn OFF when the EGR valve is commanded OPEN. Does the EGR valve pass both tests? If yes, go to next step. If no, go to step  6 .
  5. Start engine. Backprobe EGR coil control circuits at PCM harness connector terminals C4-5 and C4-16 with a test light connected to ground. The test light should NOT illuminate on either circuit. Continue to backprobe both EGR control circuits with the test light. Observe the test light on each circuit while commanding the EGR valve OPEN to 5% with the scan tool. The test light should illuminate when the EGR valve is commanded OPEN. Does the EGR valve pass both tests? If yes, go to step  7 . If no, go to next step.
  6. Turn ignition off. Disconnect the EGR valve electrical connector. Use a DVOM to measure the following EGR valve coil windings for the specified value of resistance. Check between EGR valve terminals No. 1 and 2, between terminals No. 2 and 3, between terminals No. 5 and 6, and between terminals No. 4 and 5. Resistance should be 20-24 ohms at 68°F (20°C). Measure the resistance between terminals No. 2 and 5 and EGR assembly body. Resistance should be infinite. Does the EGR valve pass all resistance tests? If yes, go to step  8 . If no, go to step  15 .
  7. Remove EGR valve. Inspect all EGR passages for any obstruction or blockage. Inspect EGR valve for physical damage or carbon deposits. Repair as necessary. Was a repair necessary? If yes, go to step  12 . If no, go to step  15 .
  8. Disconnect the EGR valve electrical connector. Turn ignition on, with engine off. Connect a test light between the harness side of terminal No. 2 and ground. Connect a test light between the harness side of terminal No. 5 and ground. Did the test light illuminate for both circuits? If yes, go to step  14 . If no, go to step  13 .
  9. Inspect the vehicle for any condition that can affect the accuracy of the Manifold Absolute Pressure (MAP) sensor: A malfunctioning or incorrectly calibrated MAP sensor, a faulty manifold vacuum supply to the MAP sensor, or an engine performance concern that can affect the engine manifold vacuum readings. Repair as necessary. Was a repair necessary? If yes, go to step  12 . If no, go to next step.
  10. Inspect the exhaust gas passages of the EGR system for the following conditions: Carbon deposits and restrictions in the EGR pipe. Carbon deposits and restrictions in the EGR passages of the exhaust manifold. Carbon deposits and restrictions in the EGR passages of the intake collector. Clean or repair any deposits and restrictions as necessary. Did you find and correct Condition? If yes, go to step  18 . If no, go to next step.
  11. Remove the EGR valve. Inspect the EGR valve for carbon or coking deposits and restrictions, leaks in the EGR valve or gasket, or a binding or incorrectly seated EGR valve plunger. Repair or replace as necessary. Did you find and correct a condition? If yes, go to step  18 . If no, go to next step.
  12. Turn ignition off. Remove DOME fuse for 30 seconds. Install DOME fuse. Reset radio clock time. Start engine. Operate the vehicle within the Conditions for Running the DTC or until the DTC P0401 diagnostic test has run. See CONDITIONS FOR RUNNING DTC  . Does the DTC run and pass? If yes, go to step  15 . If no, go to DIAGNOSTIC AIDS  .
  13. Repair the ignition positive voltage supply to the EGR valve. After repairs, go to step  18 .
  14. Inspect for an open or a short in the EGR coil control circuits that did not illuminate On and Off in step  3 or step  4 . Repair as necessary. Did you find and correct a condition? If yes, go to step  18 . If no, go to step  16 .
  15. Replace EGR valve. After repairs, go to step  18 .
  16. Inspect PCM and EGR sensor electrical connectors for poor connections. Repair as necessary. Did you find and correct Condition? If yes, go to step  18 . If no, go to next step.
  17. Replace PCM. Perform PCM relearn procedure. See POWERTRAIN CONTROL MODULE  under PROGRAMMING. After replacing PCM, go to next step.
  18. Turn ignition off. Remove DOME fuse for 30 seconds. Install DOME fuse. Reset radio clock time. Start engine. Operate the vehicle within the Conditions for Running the DTC or until the DTC P0401 diagnostic test has run. See CONDITIONS FOR RUNNING DTC  . Does the DTC run and pass? If yes, go to next step. If no, go to step  2 .
  19. With a scan tool, observe the stored information, Capture Info. Does the scan tool display any DTCs that you have not diagnosed? If yes, see DIAGNOSTIC TROUBLE CODE DEFINITIONS  . If no, system is okay.