Diagnostic Procedures
- Perform diagnostic system check - engine controls. See DIAGNOSTIC SYSTEM CHECK - ENGINE CONTROLS under SELF-DIAGNOSTIC SYSTEM. After performing diagnostic system check - engine controls, go to next step.
- Start engine and observe for a misfire at idle. If a misfire is present, go to step 4 . If a misfire is not present, go to next step.
- Install a scan tool. Turn ignition on, with engine off. Perform the scan tool Clear DTC Information function. Operate the vehicle within the Freeze Frame data as specified or until the DTC P0300 diagnostic test has run. Is a DTC P0300 set? If yes, go to next step. If no, see DIAGNOSTIC AIDS .
- Turn ignition off. Visually and physically check the following items:
- Improperly operating or leaking PCV valve.
- Incorrect PCV valve.
- Vacuum leak at intake manifold or gasket.
- Vacuum leak at a cracked, split or worn vacuum hose.
Repair as necessary. Was repair necessary? If yes, go to step 18 . If no, go to next step.
- Disconnect fuel injector harness connectors. Remove No. 1 ignition coil. Install a Spark Tester (J-26792) to No. 1 ignition coil spark plug boot. Crank engine while observing spark tester. Repeat procedure on all ignition coils. Did the test of each ignition coil indicate a crisp blue spark while cranking the engine? If yes, go to step 9 . If no, go to next step.
- Check ignition coils and spark plug wires for cracks, terminal corrosion, carbon tracking and moisture. Repair as necessary. Was a repair necessary? If yes, go to step 18 . If no, go to next step.
- Turn ignition off. Swap ignition coils. Replace the suspected faulty ignition coil with a functioning ignition coil. Install spark tester and test for spark, as performed in step 4 . If test indicates a crisp Blue spark while cranking engine, go to next step. Did the test indicate a crisp Blue spark while cranking engine? If yes, go to next step. If no, diagnose electronic ignition system. See ELECTRONIC IGNITION SYSTEM under IGNITION SYSTEMS in BASIC DIAGNOSTIC PROCEDURES - 2.0L & 2.5L TRACKER article.
- Replace faulty ignition coil. After repairs, go to step 18 .
- Remove spark plugs. Visually and physically inspect each spark plugs for correct performance and condition. Replace as necessary. Did any spark plugs need replacement? If yes, go to step 12 . If no, go to next step.
- Turn ignition off. Disconnect fuel injector harness connectors. Install Injector Test Light (J-34730-2B) into each of the fuel injector harness connectors one at time. Observe injector test light for each injector while cranking engine. Did the fuel injector test light flash for each fuel injector while cranking the engine? If yes, go to next step. If no, diagnose fuel injector circuit. See FUEL INJECTOR CIRCUIT DIAGNOSIS under FUEL SYSTEMS in SYSTEM & COMPONENT TESTING - 2.0L & 2.5L TACKER article.
- Check fuel injectors for proper operation. See FUEL INJECTOR BALANCE TEST under FUEL SYSTEMS in SYSTEM & COMPONENT TESTING - 2.0L & 2.5L TRACKER article. Was a faulty fuel injector found and replaced? If yes, go to step 18 . If no, go to step 14 .
- Was a spark plug was replaced due to rich fueling condition or wet fuel fouling? If yes, diagnose fuel system. If no, go to next step.
- Was a spark plug is replaced because of fuel, oil or coolant fouling? If yes, go to step 15 . If no, go to step 18 .
- Check EGR valve for excessive flow or sticking open. Repair as necessary. Was a repair necessary? If yes, go to step 18 . If no, go to next step.
- Check engine for the following mechanical problems:
- Worn or faulty camshaft.
- Leaky or sticky valves.
- Excessive valve deposits.
- Broken or leaky piston rings.
- Weak valve springs.
- Incorrect valve timing.
- Intake (vacuum) leaks.
- Leaking head gasket.
- Loose or broken motor mounts.
Repair as necessary. Was a basic engine mechanical concern found and repaired? If yes, go to step 18 . If no, go to next step.
- Remove CMP sensor (sensor is located on rear of cylinder head). Check CMP sensor for damage, foreign material on sensor (magnet) surface, and water or corrosion at connector terminals. Was repair necessary? If yes, go to step 18 . If no, go to next step.
- Check CMP sensor signal rotor in CMP sensor housing for damaged teeth, foreign material, and correct installation. Repair as necessary. Was a repair necessary? If yes, go to step 18 . If no, see DIAGNOSTIC AIDS .
- Turn ignition off. Remove DOME fuse for 30 seconds. Install DOME fuse. Reset radio clock time. Start engine. Operate the vehicle within the Conditions for Running the DTC or until the DTC P0300 diagnostic test has run. Does the DTC run and pass? If yes, go to next step. If no, go to step 2 .
- Turn ignition on, with engine off. Using scan tool, observe the stored information and Capture Info. Does the scan tool display any DTCs that you have not diagnosed? If yes, see DIAGNOSTIC TROUBLE CODE DEFINITIONS . If no, system is okay.